Cabletron Systems SEHI100TX instruction

Installing the EPIM-100TX or the EPIM-100FX

4.6INSTALLING THE EPIM-100TX OR THE EPIM-100FX

This section contains procedures on how to install the EPIM-100TX or the EPIM-100FX to upgrade or change the capabilities of your SEHI. After installing a new EPIM, refer to the appropriate EPIM section in Appendix A to verify proper operation.

Observe all static precautions while handling an EPIM.

!

C AUT IO N

Install an EPIM-100TX or an EPIM-100FX as follows:

When removing an EPIM, pull the module straight out to

!prevent damage to the connector.

C AUT IO N

1.Remove the coverplate or the existing EPIM (whichever applies).

2.Slide the new EPIM into place, making sure that the connectors on the rear of the EPIM align correctly and firmly with the connector inside the SEHI. Refer to Figure 4-7.

3.Install the mounting screw.

EPIM 1

LNK

EPIM-100TX

1511_09

Figure 4-7 Installing an EPIM-100TX/FX

SEHI100TX User’s Guide

4-9

Image 31

Cabletron Systems SEHI100TX Installing the EPIM-100TX or the EPIM-100FX, Install an EPIM-100TX or an EPIM-100FX as follows

Contents

Intelligent Stackable HUB USER’S Guide SEHI100TX User’s Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents SEHI100TX User’s Guide Vii Chapter Introduction Using this Manual Following conventions are used throughout this document Document Conventions Related Manuals Getting Help Sehi Overview Chapter Sehi Features and Options Sehi Features and Options Sehi Features Stackable Capabilities Remote Network Management Rack Mounting CapabilitiesOptional 100BASE-TX and 100BASE-FX EPIMs Cable Specifications Chapter Installation Requirements SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Speciﬁcations Multimode Speciﬁcations for the EPIM-100FX Network Cable Lengths COM Port Requirements Network Port Specifications Power Supply Requirements Operating SpecificationsEnvironmental Requirements Agency Approvals Physical Specifications Unpacking the Sehi Chapter Installation Nvram Switch Location PRE-INSTALLATION Checkout SEHI100TX-22 Tabletop or Shelf Installation Screws Strain-Relief Bracket Rackmount Installation Rackmount Installation Installing the Sehi in the Rack Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Install an EPIM-100TX or an EPIM-100FX as follows Installing the EPIM-100TX or the EPIM-100FX Connecting the Sehi to the Network Chapter Connecting to the NetworkConnecting to Network Ports Sehi Network Ports Connecting a UTP Segment to an EPIM-100TX Position X crossed over RX+ TX+ Position = Not crossed over EPIM-100FX Port Connecting a Fiber Segment to the EPIM-100FX Testing the Installation Installation Test Chapter Troubleshooting Using Lanview Using Lanview Epim 1 RCV LED Using the Reset Button Setting the Nvram Switch Chapter Local Management Keyboard Conventions Function Local Management Keyboard Conventions Management Terminal Setup Console Cable Conﬁguration Management Terminal Setup Parameters Sehi Local Management Accessing Local Management Feature Selection Screen Feature Selection Screen Community Name Table Screen Community Name Table Screen Editing the Community Name Field Configuration Configuration Screen Displays the IP address of the Sehi Setting the Subnet Mask Setting the IP Address Using the Port Enable Override Setting the Default Gateway Trap Table Screen Exiting the Conﬁguration Screen Exiting the Trap Table Screen 1 Conﬁguring the Trap Table Snmp Tools Screen Snmp Tools Screen Lets you retrieve MIB objects using Snmp protocol Getting Individual OIDs Setting an OIDGetting the Next OID Walking Through OIDs Viewing Multiple OIDs Cycling Through OIDs Stepping Through OIDsExiting the Snmp Tools Screen Device Statistics Screen Device Statistics Screen Displays the number of errors due to misaligned packets Module Number Sequence Selecting the Appropriate Module/Port Using the Disable Port Command Using the Enable Port CommandExiting the Device Statistics Screen Epim Specifications Appendix a Epim SpecificationsEPIM-100TX EPIM-100FX Appendix B Image File Download Using Oids Setting UP a Unix Workstation AS a Tftp Server Standard Local Download Table B-1 OIDs and Settings Numerics Index Index-2 Power Supply Cord