Chaparral FS2620R - page 63

Displaying Router Information

3-33

FC Speed 1G

2G

Auto

GBIC

receive

status

Signal present—FC is up and

running

No signal—FC is not up and

running

Node

WWN

FC World Wide Name for

node.

Port WWN FC World Wide Name for

port.

Loop ID, if

the

topology is

LOOP.

SOFT or a specific number

as set in the Router

Administrator software.

Current

Loop

ID/Loop

Inactive

Currently

assigned value if

the topology is

LOOP, or

Inactive if the

FC link is not

active.

FC Addr 24-bit FC address or None if

the FC link is not active.

AL_PA, if

the

topology is

LOOP.

Currently

assigned value

or None if the

FC link is not

active.

Router

LUN

SOFT, NONE, or specific

number as set in the Router

Administrator software.

Current Currently

assigned value

or Inactive if the

Router LUN is

set to NONE.

CHAN 0-5 Initiator ID SCSI ID of router on each

channel as set in the Router

Administrator software.

Bus Speed Hardware runs

as Ultra3 160

MB/sec

Domain

Validation

Enabled or Disabled

ROUTER Alarm ENABLED or DISABLED

as set in the Router

Administrator software.

Scan Delay Number of

seconds the

router waits to

the scan the bus

as set in the

Router

Administrator

software.

Table 3-5. Configuration information (Continued)

Group Field What displays Field What displays

Contents

Main Page Copyright Trademarks Changes Technical Support Federal Communications Commission Radio Frequency Interference Statement Canadian Compliance Statement EMC (Electromagnetic Compatibility) Immunity Safety Laser Safety Page Contents 1 Introduction 2 Installing the Router 3 Configuring the Router 4 Troubleshooting A Address and Device Mapping B Configuring the Router for TCP/IP Page Page Introduction About this Guide Conventions ! Chaparral FS2620R Router Benefits and Features Page About Serverless Backup and Restore Specifications ! Installing the Router 1 2 3 4 Unpacking the Router 1 2 3 4 Installing the Router Installing on a Desktop 1 2 Installing in a Rack Connecting the Router Connecting to the SCSI Channels ! Connecting to the Fibre Channel Port Connecting to the RS-232 Port 1 2 3 Connecting to the Ethernet Port Powering Up All Devices ! 1 2 Understanding the LED Status Lights Page Router Default Settings Installation Configuration Examples Page Page Page Configuring the Router Accessing the Router Administrator Software Accessing the Router Administrator Using the RS- 232 Serial Port 1 Page Accessing the Router Administrator Using the Ethernet Port 1 2 3 4 1 2 3 4 5 Configuring the Routers Network Settings Page SNMP Configuration Screen Page Accessing the Network Management System 1 2 Navigating the Router Administrator Software Page Changing the Screen Display Changing Router Configuration Configuring the FC Host Channels 1 2 Page 5 6 7 8 Changing the SCSI ID Assigned to Each Router Channel Page Setting the Date and Time Page Changing the Scan Delay Enabling and Disabling the Alarm 1 2 4 3 Restoring the Default Settings Rebooting the Router Changing and Displaying Device Information Changing the Mapping Mode (AUTO or FIXED) 1 2 3 Changing Device Addresses (FC LUNs) Page Changing Addressing Method 1 2 3 Displaying the Devices Connected to the Router Displaying the FC-to-SCSI Address Map 1 2 3 Displaying Router Information Displaying the Event Log 1 2 Capturing the Event Log File 1 2 3 4 5 6 7 Displaying Hardware and Configuration Information Page 1 2 3 Page Displaying the Routers FC LUN Upgrading Firmware Upgrading the Controllers Firmware 1 2 3 ! Upgrading LAN Firmware Page Page Troubleshooting Chaparral Technical Support Problems During Bootup ! 1 2 3 Restoring the Default Configuration Through the Flash Utility Page Terminal Emulator and COM Port Problems Device SCSI Channel Problems Router is Not Responding 1 2 3 Setting Up Debug Logging Using the Loader Diagnostics Menu Using the Loader Utility Menu Voltage and Temperature Errors and Warnings Page A Address and Device Mapping FS2620R Rack Model Users Guide A-2 Figure A-1. FS2620R device address mapping Loop ID to AL_PA Mapping Page Page B Configuring the Router for TCP/IP Using Address Resolution Protocol 1 2 Dynamic Host Configuration Protocol Configuration 1 2 Simple Network Management Protocol Configuration Page C Reference Documents Standards Books Glossary Page Page Page Index A C D E F G H I L M R S T