Chaparral FS2620R manual

Simple Network Management Protocol Configuration

To discover which IP address was assigned to the router:

1Follow the steps above for ARP to bind the router MAC address to a temporary static IP address.

2Use the command arp –gto display your computer’s the IP-to-MAC address table. This table contains two entries corresponding to the router MAC address. One of the entries contains the temporary static IP address you just bound to the router MAC address, and the other entry is the DHCP-assigned IP address. You can use the DHCP assigned address to access the router from any computer on the network.

Simple Network Management Protocol Configuration

Remaining TCP/IP parameters, such as Simple Network Management Protocol (SNMP) traps, can be configured after the TCP/IP configuration is done. Ask your system administrator to configure these parameters according to the requirements of your LAN. For more information about SNMP implementation, contact Chaparral regarding SNMP, or visit our Web site at: www.chaparralnet.com.

❒

B-3

Image 85

Chaparral FS2620R manual Simple Network Management Protocol Configuration

Contents

User’s Guide Page Copyright Canadian Compliance Statement Safety Page Contents Address and Device Mapping Reference Documents FS2620R Rack User’s Guide Viii About this Guide Introduction Conventions Chaparral FS2620R Router Benefits and FeaturesBold Chaparral FS2620R Router Benefits and Features About Serverless Backup and Restore Physical Specifications Environmental To unpack the router Unpacking the Router Installing on a Desktop Installing the RouterInstalling in a Rack To install the FS2620R on a desktop To install the router in a rack Connecting the Router Rear panel components Connecting to the Scsi Channels To connect devices to the Scsi channels Connecting to the Fibre Channel PortTo connect to the Fibre Channel port To connect to the RS-232 port Connecting to the RS-232 Port Connecting to the Ethernet Port Powering Up All DevicesTo power up Scsi devices To connect to the Ethernet port To make the host FC connection Understanding the LED Status Lights Description Color Function Label Setting Default For more information, see Router Default Settings Simple loop configuration example Installation Configuration Examples Multiple servers on a SAN FC-AL Multiple SANs with fabric FC-SW Combination loop and switch configuration Accessing the Router Administrator Software Configuring the Router FS2620R Rack Model User’s Guide Accessing the Router Administrator Using the Ethernet Port FS2620R Rack Model User’s Guide Configuring the Router’s Network Settings System Configuration Screen Snmp Configuration Screen Restarting the Router To access the network management system Navigating the Router Administrator Software Menu Tree illustrates the main menu options and sub-options Changing the Screen Display Changing Router Configuration Configuring the FC Host Channels To configure an FC host channel Select Enabled or Disabled and press Enter Changing Router Configuration System confirms that you want to make the changes To change the Scsi ID assigned to a Scsi channel Changing the Scsi ID Assigned to Each Router Channel FS2620R Rack Model User’s Guide To set the router’s date Setting the Date and Time To set the router’s time Enabling and Disabling the Alarm Changing the Scan DelayTo change the scan delay Alarm threshold What to do when the alarm sounds To enable or disable the alarm Restoring the Default Settings Rebooting the RouterTo restore the default settings Select Restore Defaults and press Enter To change the mapping mode Changing the Mapping Mode Auto or FixedChanging and Displaying Device Information Changing Device Addresses FC LUNs Select Mapping Mode press Enter To change the device FC LUNs See Changing the Mapping Mode Auto or Fixed on Displaying the Devices Connected to the Router Changing Addressing MethodSelect Addressing Method and press Enter To display the devices connected to the router Displaying the FC-to-SCSI Address MapTo display the address map Displaying the Event Log Displaying Router Information Select View Event Log and press Enter To display one event at a time To display a full page of events Capturing the Event Log File To capture the event log file Displaying Hardware and Configuration Information Gbic To display hardware information only To display hardware and configuration information To display the router’s LUN Displaying the Router’s FC LUNSelect Display Address Map and press Enter Upgrading Firmware To upgrade the router’s firmwareUpgrading the Controller’s Firmware Upgrading LAN Firmware To upgrade the Ethernet card’s firmware Upgrading Firmware FS2620R Rack Model User’s Guide Chaparral Technical Support Problems During Bootup FS2620R Rack Model User’s Guide Select 2. Clear Configuration and press Enter To restore the default configuration Solution Terminal Emulator and COM Port Problems Router is Not Responding Device Scsi Channel Problems To set up debug logging Setting Up Debug Logging Using the Loader Utility Menu Using the Loader Diagnostics MenuVoltage and Temperature Errors and Warnings FS2620R Rack Model User’s Guide Address and Device Mapping Device Loop ID to Alpa Mapping ALP 114 115 116 117 118 119 120 121 122 100 123 101 124 102 125 Using Address Resolution Protocol Configuring the Router for TCP/IP To use ARP to resolve addresses in Windows Dynamic Host Configuration Protocol ConfigurationArp -s IP address 005013fx-xx-xx To discover which IP address was assigned to the router Simple Network Management Protocol Configuration FS2620R Rack Model User’s Guide Standards Reference Documents SBP Books Glossary G6322/G7324 User’s Guide Glossary G6322/G7324 User’s Guide Index Dhcp Page FS2620R Rack Model User’s Guide TCP/IP FS2620R Rack Model User’s Guide