Cisco Systems 100/200/300/400

4-6

Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide

OL-13478-03

Chapter 4 Installing the Internet Streamer CDS Software and Initially Configuring a CDE

Running the BIOS Setup Utility

Figure 4-6 Advanced Settings Menu

Step 11 Choose IDE Configuration and press Enter. The IDE Configuration screen appears (see Figure 4-7).

Figure 4-7 IDE Configuration Screen

a. Set the IDE Configuration option to P-ATA Only.

b. Set the S-ATA Running Enhanced Mode option to No.

c. Set the P-ATA Channel Selection option to Both.

Note On the CDE100, the Primary IDE Slave is connected to the internal CD-ROM drive, the

Secondary IDE Master is connected to a 128-MB compact flash drive.

Step 12 Press Esc to return to the Advanced menu. Choose Super I/O Configuration and press Enter. The

Configure Super I/O Chipset screen appears (see Figure 4-8).

Contents

Main Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide Page CONTENTS Page Page Page Preface Document Revision History Document Organization Objectives Audience Related Documentation Conventions Safety Information Referral Warning Warning Definition x xi xii xiii Page Obtaining Documentation and Submitting a Service Request Page Overview of the Content Delivery Engines Cisco Internet Streamer CDS Overview Cisco TV CDS Overview OnDemand Application Video Accelerator Software Hardware Features 1-4 Figure 1-4 CDE200 Rear View Figure 1-5 CDE300 Front View Figure 1-6 CDE300 Rear View Page Control Buttons Page LED Indicators Page Page Input/Output Ports and Connectors 3 6 7 4 5 3 4 5 6 7 2 3 4 5 5 5 76 Page Page Preparing to Install the Content Delivery Engines Site Requirements Preventing Electrostatic Discharge Damage Environmental, Physical, and Power Specifications 2-3 For information on the power requirements of the CDEs, see these sections: Safety Warnings 2-4 2-5 AC Power Option Warnings DC Power Option Warnings Safety Guidelines General Precautions Protecting Against Electrostatic Discharge Safety Information Emissions Disclaimer Intended Uses If AC Power Supplies Are Installed If DC Power Supplies Are Installed Temperature and Ventilation Installing the Content Delivery Engines Server Types Tools and Parts Required Unpacking the Box Verifying Contents Inspecting for Damage Installing the CDEs Reviewing Rack Installation Safety Guidelines Preparing the CDEs for Rack Installation Installing CDEs in the Rack Making Physical Connections Connecting Power Cords 4 5 3 6 7 3 4 5 6 7 Page Connecting Network Cables SE and SR System Vault and Streamer System 54 6 7 ISV System Installing or Removing Disk Drives sdd sdc sdb sda Page Page Page Installing the Internet Streamer CDS Software and Initially Configuring a CDE Before You Begin Installation and Configuration Order Running the BIOS Setup Utility Running the BIOS Setup Utility for the CDE100 Page Page Page Page Page Running the BIOS Setup Utility for the CDE200 Page Page Page Installing the Software Initially Configuring a CDE Assigning the Primary Interface Running the Setup Utility Verifying the CDSM Page Page Page Hardware Troubleshooting Troubleshooting Ethernet Adapters Troubleshooting SATA Drives A Technical Specifications Specifications CDE100 CDE200 CDE300 CDE400 Management B Connector Pin Assignments Serial Console Interface Connector Pin Assignments Serial Port Connector Ethernet Connector Pin Assignments Ethernet Port Connector B-4 Figure 2-2 shows the pin number assignments for the Ethernet RJ-45 port. Cable Pin Assignments B-5 Figure B-4 Pin Assignments and Wiring for an RJ-45 Straight-Through Cable Figure B-5 Pin Assignments and Wiring for an RJ-45 Crossover Cable Page C CDEs with Serverworks Chipset Specifications CDE100 CDE200 CDE200 (IBM) CDE300 CDE400 Connector Pin Assignments 431 5 6 17 24 5 6 8 43 6 87 51 2 7 4 5 6 Page Page D Connecting DC Power DC Power Overview Connecting DC Power to a CDE200 3 4 56 9 7 Page Disconnecting Power and Replacing a PM on a CDE200 Connecting DC Power to a CDE300 Page Disconnecting Power and Replacing a PM on a CDE300 Connecting DC Power to a CDE400 Page Page Disconnecting Power and Replacing a PM on a CDE400 DC Power Cable Connector and Pinouts Page INDEX Numerics A B Page D E F G H I L M P R S T U V