Cisco Systems 100/200/300/400 - page 60

4-8

Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide

OL-13478-03

Chapter 4 Installing the Internet Streamer CDS Software and Initially Configuring a CDE

Running the BIOS Setup Utility

Figure 4-10 Exit Options Screen

Step 15 Ensure that the CD with the CDS image is in the internal CD-ROM drive and press Enter to confirm and

reboot the system. Your configuration is saved, you exit the BIOS Setup menu, and the system reboots.

The system boots from the image on the CD. This requires a terminal server to be hooked up to the serial

port of the CDE100. All communication is done through the serial port (see the “Before You Begin”

section on page 4-1 for terminal server settings).

Once the CD starts booting, it displays a spinning “|” symbol for approximately five minutes. Allow the

booting to proceed and monitor the sequence from a remote terminal provided by the terminal server.

The CD boot menu is displayed at the conclusion of this boot sequence:

Welcome to the installer. The installer enables installation of a new software image onto

your system, or recovers a previous image in the event that the hardware was changed.

MODEL: CDE100

FLASH: found, directory validated

COOKIE: valid

IMAGE: DEVELOPMENT[jbohach-lnx02:/data/jbohach/ws/ipvideo/refact-dev-1

FLASHDEV: /dev/hdX

Installer Main Menu:

1. Configure Network

2. Manufacture flash

3. Install flash cookie

4. Install flash image from network

5. Install flash image from cdrom

6. Install flash image from disk

7. Wipe out disks and install.bin image

8. Exit (and reboot)

9. Force manufacturing flash

Choice [0]:

Step 16 Confirm that the FLASHDEV: line near the top of the menu displays something similar to “/dev/hdX”,

where “X” can be any letter.

a. If no flash device is found, choose Option 8 to exit and reboot, and enter the BIOS Setup menu

again. Confirm that the BIOS detected the flash device.

b. If the BIOS detects the CD-ROM drive but the CD installation menu is not displayed, this is an

abnormal condition. Contact Cisco Technical Support at the following URL:

www.cisco.com/techsupport

Contents

Main Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide Page CONTENTS Page Page Page Preface Document Revision History Document Organization Objectives Audience Related Documentation Conventions Safety Information Referral Warning Warning Definition x xi xii xiii Page Obtaining Documentation and Submitting a Service Request Page Overview of the Content Delivery Engines Cisco Internet Streamer CDS Overview Cisco TV CDS Overview OnDemand Application Video Accelerator Software Hardware Features 1-4 Figure 1-4 CDE200 Rear View Figure 1-5 CDE300 Front View Figure 1-6 CDE300 Rear View Page Control Buttons Page LED Indicators Page Page Input/Output Ports and Connectors 3 6 7 4 5 3 4 5 6 7 2 3 4 5 5 5 76 Page Page Preparing to Install the Content Delivery Engines Site Requirements Preventing Electrostatic Discharge Damage Environmental, Physical, and Power Specifications 2-3 For information on the power requirements of the CDEs, see these sections: Safety Warnings 2-4 2-5 AC Power Option Warnings DC Power Option Warnings Safety Guidelines General Precautions Protecting Against Electrostatic Discharge Safety Information Emissions Disclaimer Intended Uses If AC Power Supplies Are Installed If DC Power Supplies Are Installed Temperature and Ventilation Installing the Content Delivery Engines Server Types Tools and Parts Required Unpacking the Box Verifying Contents Inspecting for Damage Installing the CDEs Reviewing Rack Installation Safety Guidelines Preparing the CDEs for Rack Installation Installing CDEs in the Rack Making Physical Connections Connecting Power Cords 4 5 3 6 7 3 4 5 6 7 Page Connecting Network Cables SE and SR System Vault and Streamer System 54 6 7 ISV System Installing or Removing Disk Drives sdd sdc sdb sda Page Page Page Installing the Internet Streamer CDS Software and Initially Configuring a CDE Before You Begin Installation and Configuration Order Running the BIOS Setup Utility Running the BIOS Setup Utility for the CDE100 Page Page Page Page Page Running the BIOS Setup Utility for the CDE200 Page Page Page Installing the Software Initially Configuring a CDE Assigning the Primary Interface Running the Setup Utility Verifying the CDSM Page Page Page Hardware Troubleshooting Troubleshooting Ethernet Adapters Troubleshooting SATA Drives A Technical Specifications Specifications CDE100 CDE200 CDE300 CDE400 Management B Connector Pin Assignments Serial Console Interface Connector Pin Assignments Serial Port Connector Ethernet Connector Pin Assignments Ethernet Port Connector B-4 Figure 2-2 shows the pin number assignments for the Ethernet RJ-45 port. Cable Pin Assignments B-5 Figure B-4 Pin Assignments and Wiring for an RJ-45 Straight-Through Cable Figure B-5 Pin Assignments and Wiring for an RJ-45 Crossover Cable Page C CDEs with Serverworks Chipset Specifications CDE100 CDE200 CDE200 (IBM) CDE300 CDE400 Connector Pin Assignments 431 5 6 17 24 5 6 8 43 6 87 51 2 7 4 5 6 Page Page D Connecting DC Power DC Power Overview Connecting DC Power to a CDE200 3 4 56 9 7 Page Disconnecting Power and Replacing a PM on a CDE200 Connecting DC Power to a CDE300 Page Disconnecting Power and Replacing a PM on a CDE300 Connecting DC Power to a CDE400 Page Page Disconnecting Power and Replacing a PM on a CDE400 DC Power Cable Connector and Pinouts Page INDEX Numerics A B Page D E F G H I L M P R S T U V