Manuals / Brands / Computer Equipment / Switch / Cisco Systems / Computer Equipment / Switch

Cisco Systems 4500 Replacing Backplane Modules on a Catalyst 4507R or 4510R Switch

1 194

Download 194 pages, 7.41 Mb

Chapter 4 Removing and Replacing FRUs

Replacing Backplane Modules on a Catalyst 4507R or 4510R Switch

4-24

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Verifying the Installation

Note To check the operation of the fans, you need to power up the chassis.

Follow these steps to verify that the new fan assembly was installed correctly:

Step 1 Listen for the fans; you should immediately hear them operating. If you do not

hear them, ensure that the fan assembly is inserted completely in the chassis and

that the faceplate is flush with the switch back panel.

Step 2 The fan tray LED should light and be green.

Step 3 If after several attempts the fans do not operate, or if you experience trouble with

the installation (for instance, if the captive installation screws do not align with

the chassis holes), contact the Cisco TAC for assistance.

Replacing Backplane Modules on a Catalyst 4507R or 4510R Switch

There are 5 redundancy modules (also called mux buffers) and 1 clock module on

a Catalyst 4507R chassis backplane. A Catalyst 4510 has 8 redundancy modules

on its backplane. They are accessible from the front if the switching modules and

supervisor engines are removed. There are two types of redundancy modules, and

they are interchangeable.

The clock module replacement procedure is identical to the redundancy module

replacement procedure, the connectors are the same. These modules are not

hot-swappable, the switch must be taken out of service to replace them.

To replace the backplane modules:

Step 1 Make sure you are grounded with an ESD strap.

Step 2 Turn off the power to the chassis.

Contents

Main Catalyst 4500 Serie s Switches Installation Guide December 2005 Page Page Page CONTENTS Page Page Page Preface Audience Organization Related Documentation Conventions Page Warnings use the following conventions: Page Page Page Obtaining Documentation and Submitting a Service Request Page Product Overview Switch Features Catalyst 4503 Switch Features Page Page Page Catalyst 4506 Switch Features Page Page Page Switch Features 1-10 Catalyst 4507R Switch Features Figure 1-3 Catalyst 4507R Switch (Front View) Power supplies Page Page Page Page 1-15 Switch Features Catalyst 4510R Switch Features Figure 1-4 Catalyst 4510R Switch (Front View) Power supplies Page Page Page Page Supervisor Engines Page Page 1-23 1-24 1-25 Page LEDs Gigabit Ethernet Uplink Ports 10-Gigabit Ethernet Uplink Ports SFP Ports Ethernet Management Port CONSOLE Port RESET Button CompactFlash Port Fan Assembly 1-31 Figure 1-13 Catal yst 4503 Airflow Figure 1-14 Catal yst 4506 Airflow 1-32 Catalyst 4500 Series Switches Installation Guide Figure 1-15 Catal yst 4507R Airflow 23456789101112 17 1-33 Figure 1-16 Catal yst 4510R Airflow Power Supplies 1-35 configurations. All the inputs in a chassis must be the same voltage (110 or 220 V). Page Power Supply LEDs Power Supply Fan Load-Sharing Feature Environmental Monitoring Feature 1400 W DC Triple-input Power Supply Operational Modes Page Page Page System Architecture Power Flow Power over Ethernet PoE Over-subscription PoE Line Cards Deploying PoE on the Cisco Catalyst 4500 Series Cisco Catalyst 4500 Series Service Provider DC Power Supply Management Flow Switching Traffic Flow Over-subscription Supervisor Redundancy Page 2-1 Preparing for Installation Electrostatic Discharge Preventing Electrostatic Discharge Damage Site Power Requirements and Heat Dissipation Power Connection Guidelines for AC-Powered Systems Page Page Page Page Page Page Page Power Connection Guidelines for DC-Powered Systems Calculating DC Input Current Ventilation Calculating System Heat Dissipation Site-Planning Checklist Page 3-1 Installing the Switch in a Rack Page Checking the Shipping Container Contents Rack-Mounting the Switch Required Installation Tools Rack-Mounting Catalyst 4500 Series Switches Page 3-7 Figure 3-1 L Brackets on the Front Edge of the Catalyst 4503 Switch 3-8 Figure 3-2 L Brackets on the Front Edge of the Catalyst 4506 Switch 3-9 Figure 3-3 L Brackets on the Front Edge of the Catalyst 4507R Switch 23456789101112 17 3-10 Figure 3-4 L Brackets on the Front Edge of the Catalyst 4510R Switch c. Attach the cable guide, if needed, using the M3 screws provided in the cable 3-11 Figure 3-5 Attaching the Cable Guide to the Catalyst 4503 Switch 3-12 Figure 3-6 Attaching the Cable Guide to the Catalyst 4506 Switch 3-13 Figure 3-7 Attaching the Cable Guide to the Catalyst 4507R Switch 2345678910 1112 17 2345678910111217 2345678910 111217 3-14 Figure 3-8 Attaching the Cable Guide to the Catalyst 4510R Switch b. Align the mounting holes in the L bracket with the mounting holes in the equipment rack. 3-15 c. Secure the chassis using at least six (three per side) 12-24 x 3/4-inch screws through the elongated holes in the L bracket and into the threaded holes in the mounting post. d. Use a tape measure and level to ensure that the chassis is installed straight and level. 3-16 Figure 3-10 Installing a Catalyst 4506 Switch in the Rack 3-17 Figure 3-11 Installing a Catalyst 4507R Switch in the Rack 3-18 Figure 3-12 Installing a Catalyst 4510R Switch in the Rack Step 4 Make sure that the ejector levers are completely closed and the supervisor engine and switching modules are installed securely. Step 5 Tighten any loose captive installation screws on the supervisor engine and the System Ground Connection Guidelines 3-20 Figure 3-14 Catalyst 4506 Grounding Holes 3-21 Figure 3-15 Catalyst 4507R Grounding Holes STATUS WS-X4448-GB-RJ45 STATUS 3-22 Figure 3-16 Catalyst 4510R Grounding Holes Parts and Required Tools Connecting System Ground and Power 3-25 Figure 3-17 Connecting System Ground on the Switch pad Grounding lug Wire Screws (M4) Page 4-1 Removing and Replacing FRUs Removing and Replacing the Power Supply 4-3 4-4 Required Tools Removing an AC-Input Power Supply Page Page Installing an AC-Input Power Supply Page Page Removing a DC-Input Power Supply Required Tools Removal Procedure 4-12 4-13 wire last (see Figure 4-13 or Figure 4-14). Statement 1046 Page Page 4-16 Installing a DC-Input Power Supply This section describes how to install a DC-input power supply. Required Tools You will need the following tools to perform this procedure: Installation Procedure Page Removing and Replacing the Chassis Fan Assembly 4-19 Figure 4-17 Catalyst 4503 System Fan Assembly 4-20 Figure 4-18 Catalyst 4506 System Fan Assembly 4-21 Figure 4-19 Catalyst 4507R System Fan Assembly 2345678910 111217 4-22 Figure 4-20 Catalyst 4510R System Fan Assembly Required Tools You will need a Phillips screwdriver for the following two procedures. Removing the Fan Assembly Installing the Fan Assembly Verifying the Installation Replacing Backplane Modules on a Catalyst 4507R or 4510R Switch Page 4-26 Page Page Page Verify the New Modules Troubleshooting System Boot Verification Problem Solving to the System Component Level Using LEDs to Identify Startup Problems Page Troubleshooting the Power Supply Troubleshooting Power Problems using Cisco IOS Troubleshooting the Fan Assembly Troubleshooting Backplane Modules Troubleshooting Switching Modules Page Troubleshooting Switching Modules Using Cisco IOS Troubleshooting Supervisor Engines Troubleshooting Supervisor Engines Using Cisco IOS Page Contacting the Cisco Technical Assistance Center 5-17 Serial Numbers Figure 5-3 Catalyst 4503 Serial Number Location 5-18 Figure 5-4 Catalyst 4506 Serial Number Location 5-19 Figure 5-5 Catalyst 4507R Serial Number Location 5-20 Figure 5-6 Catalyst 4510R Serial Number Location 113784, 781-00251-01A0 APPENDIX A Specifications Catalyst 4503 Switch Specifications Catalyst 4506 Switch Specifications Page Catalyst 4507R Switch Specifications Page Catalyst 4510R Switch Specifications Page Catalyst 4500 Series Power Supplies Page Page Page Page Page Page Page Page Page Page Page APPENDIX B Repacking a Switch B-2 INDEX Numerics A B C D E F G H I L M O P R S T U V W