Cisco Systems 6000 - page 62

62

Catalyst 6000 Family Content Switching Module Installation and Configuration Note

78-11631-02 Rev. A0

Obtaining Technical Assistance

This document is to be used in conjunction with the documents listed in the “Related Documentation” section.

AccessPath, AtmDirector, Browse with Me, CCIP, CCSI, CD-PAC, CiscoLink, the Cisco Powered Network logo, Cisco Systems Networking Academy, the Cisco Systems

Networking Academy logo, Cisco Unity, Fast Step, Follow Me Browsing, FormShare, FrameShare, IGX, Internet Quotient, IP/VC, iQ Breakthrough, iQ Expertise, iQ FastTrack,

the iQ Logo, iQ Net Readiness Scorecard, MGX, the Networkers logo, ScriptBuilder, ScriptShare, SMARTnet, TransPath, Voice LAN, Wavelength Router, and WebViewer are

trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and Discover All That’s Possible are service marks of Cisco Systems, Inc.; and Aironet,

ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems,

Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastSwitch, GigaStack, IOS, IP/TV,

LightStream, MICA, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, SlideCast, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO

are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.

All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0110R)

Copyright © 2001, Cisco Systems, Inc.

All rights reserved. Printed in USA.

Contents

Main Catalyst 6000 Family Content Switching Module Installation and Configuration Note Contents Overview Features Front Panel Description Status LED RJ-45 Connector Operation Mode Page Client-to-CSM-to-Server Traffic Flow Safety Overview System Requirements Memory Requirements Hardware Supported Environmental Requirements Power Requirements Software Requirements Required Tools Installing the Content Switching Module Preparing to Install the CSM Installing the CSM Installing the Content Switching Module SUPERVISOR2 Figure 4 Slot Numbers on Catalyst 6000 Family Switches Warning directly to the supervisor engine or switching-module ports. Note If possible, place switching modules between empty slots that contain only switching-module filler plates (Cisco part number 800-00292-01). FAN STATUS Power supply 2 (redundant) switching module) to the desired slot. until the switching-module faceplate contacts the ejector levers. (See Figure6.) touch the printed circuit boards or connector pins. in the slot. (See Figure 5.) Figure 5 Installing Modules in the Catalyst 6000 Family Switch Verifying the Installation Using the Command-Line Interface Accessing Online Help Upgrading to a New Software Release Upgrading from the Supervisor Engine Bootflash Upgrading from a PCMCIA Card Upgrading Over the Network Configuring the Content Switching Module Page Configuring VLANs * ** Configuring Client-Side VLANs Configuring Server-Side VLANs Configuring Server Farms Configuring Real Servers Configuring Policies Configuring Maps Page Configuring Sticky Groups Configuring Virtual Servers Configuring TCP Parameters Configuring Dynamic Feedback Protocol Configuring Redirect Virtual Servers Configuring Client NAT Pools Configuring Server NAT Writing and Restoring Configurations Configuration Examples Single Subnet (Bridge) Mode Configuration Page Secure (Router) Mode Configuration Fault-Tolerant Configuration Page Page To configure the primary (A) CSM for fault tolerance, perform this task (see Figure12): Command Purpose mode. VLAN mode1. Assign the Content Switching IP address on VLAN 1. Page Configuring HSRP HSRP Configuration Overview Creating the HSRP Gateway Configuring CSM VLANs Note To allow tracking to work, preempt must be ON. Step 2 Configure VLANs on HSRP FT2 as follows: Configuring Probes for Health Monitoring Page Commands Available to all Probe Configurations HTTP Probe ICMP Probe TCP Probe FTP, SMTP, and Telnet Probe DNS Probe Submode Configuring Route Health Injection Understanding RHI RHI Overview Routing to VIP Addresses Without RHI Routing to VIP Addresses With RHI Understanding How the CSM Determines VIP Availability Understanding Propagation of VIP Availability Information Configuring RHI for Virtual Servers Regulatory Standards Compliance Translated Safety Warnings Safety Information Referral Warning Wrist Strap Warning Blank Faceplate Installation Requirement Warning Page Qualified Personnel Warning Related Documentation Obtaining Documentation World Wide Web Documentation CD-ROM Ordering Documentation Documentation Feedback Obtaining Technical Assistance Cisco.com Technical Assistance Center Contacting TAC by Using the Cisco TAC Website Contacting TAC by Telephone