Configuration Overview | Cisco Systems 6000 manual

Configuring the Content Switching Module

If the Multilayer Switch Function Card (MSFC) is used on the next hop router on either the client or the server side VLAN, then the corresponding Layer 3 VLAN interface must be configured.

Caution The MSFC cannot be used simultaneously as the router for both the client and the server side. Do not configure the Layer 3 VLAN interface for both the client and the server side.

This example shows how to configure the Layer 3 VLAN interface:

Router>

Router> enable

Router# config

Router(config)# interface vlan 130

Router(config-if)#ip address 10.10.1.10 255.255.255.0

Router(config-if)# no shutdown

Router(vlan)# exit

Figure 7 shows an overview of the configuration process. Required and optional operations are shown.

Note Configuring policies is not necessary for basic Layer 4 load balancing.

Figure 7 Configuration Overview

Configure VLANs (required)

Configure server farm (required)

Configure real servers (required)

Configure policies (optional)

Configure virtual servers (required)

Configure other optional

parameters

	Save and restore	47529
	configurations	47529
	configurations

	Catalyst 6000 Family Content Switching Module Installation and Configuration Note
20	78-11631-02 Rev. A0

Image 20

Cisco Systems 6000 manual Configuration Overview

Contents

Contents Overview These sections describe the CSM FeaturesDescribes the features of the CSM Status LED CSM front panel features are shown in FigureFront Panel Description Off Red Orange Green Green to Orange Operation ModeRJ-45 Connector Content Switching Module and Servers Client-to-Content Switching Module-to-Server Traffic Flow Client-to-CSM-to-Server Traffic Flow Safety Overview Memory Requirements CSM memory is not configurableSystem Requirements Power Requirements Hardware SupportedEnvironmental Requirements 72-876-01 Console Cable Not applicable Installing the Content Switching Module Preparing to Install the CSMRequired Tools Software Requirements Installing the CSM Power supply Installing Modules in the Catalyst 6000 Family Switch Verifying the Installation Verifying the Installation Upgrading to a New Software Release Using the Command-Line InterfaceAccessing Online Help Upgrading from the Supervisor Engine Bootflash Set up a session between the supervisor engine and the CSMCSM upgrade 127.0.0.zz c6slb-apc.revision-num.bin Routerconfig# power cycle module slot-number Routerconfig# tftp-server slotxc6slb-apc.revision-num.bin CSM upgrade slot0 c6slb-apc.revision-num.binRouter config# power cycle module slot-number Upgrading from a Pcmcia Card Configuring the Content Switching Module SwitchportSwitchport access vlan Router# vlan database Configuration Overview Configuring VLANs Configure the required parameters in the following sections Configuring VLANs See for the following notes Configuring Client-Side VLANs Configuring Server-Side VLANs Configuring Server Farms Configuring Real Servers Configuring Policies Configuring Maps Configure multiple cookies into a cookie map Configure multiple cookies Configuring Sticky Groups Configuring Virtual Servers Configuring TCP Parameters Configuring Dynamic Feedback Protocol Configuring Redirect Virtual Servers Configuring Client NAT Pools Writing and Restoring Configurations Configuring Server NAT Configuration Examples Single Subnet Bridge Mode Configuration Enter the Vlan mode Configure a client-side VlanConfigure a server-side Vlan Exit to have the configuration take effect Create the client-side Vlan 2 and enter the SLB Secure Router Mode ConfigurationVlan mode Fault-Tolerant Configuration Routerconfig# ip slb vlan 3 serverCreate the server-side Vlan 3 and enter the SLB Exit the submode Router# configure terminal Routerconfig# mac access-list extended VenusRouterconfig# int GigabitEthernet 2/1 Routerconfig-if#service-policy input Venus Fault-tolerant configuration, the following rules apply Configuration Parameter On Both Content Switching Modules Create the client-side Vlan 2 and enter the SLB Vlan mode Assign the Content Switching IP address onRouter B Hsrp address 192.158.38.10 Assign the default route for Vlan Define Vlan 9 as a fault-tolerant VlanCreate the Content Switching primary Configure a client-side VLAN2 Configuring Hsrp Hsrp Configuration Overview Configure Switch 2-FT2 Hsrp secondary as follows CSG Vlan Configuring CSM VLANs Configure VLANs on Hsrp FT2 as follows Add ports to the EtherChannel as follows Configuring Probes for Health MonitoringConfigure EtherChannel on both switches as follows Probe-name is the name of the probe being configured it has Http creates an Http probe with a default configurationIcmp creates an Icmp probe with a default configuration Telnet creates a Telnet probe with a default configuration Commands Available to all Probe Configurations Http Probe Icmp Probe DNS Probe Submode TCP ProbeFTP, SMTP, and Telnet Probe RHI Overview Configuring Route Health InjectionUnderstanding RHI Routing to VIP Addresses Without RHI Routing to VIP Addresses With RHI Configuring RHI for Virtual Servers Routerconfig# ip slb vserver vserver1Understanding How the CSM Determines VIP Availability Understanding Propagation of VIP Availability Information Regulatory Standards Compliance Translated Safety WarningsSafety Information Referral Warning Wrist Strap Warning Blank Faceplate Installation Requirement Warning Translated Safety Warnings Release Notes for Catalyst 6000 Family IOS Software Related DocumentationQualified Personnel Warning Obtaining Documentation World Wide WebDocumentation CD-ROM Ordering Documentation Contacting TAC by Using the Cisco TAC Website To access Cisco.com, go to the following websiteObtaining Technical Assistance Cisco.com Contacting TAC by Telephone Obtaining Technical Assistance