4-25
Layer 3 Switching Software Feature and Configuration Guide
78-6235-04, Cisco IOS Release 12.0(10)W5(18)
Chapter4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst8540)
The following example shows output for the show controllers pos command with the detail option:Router# show controller pos 2/0/0 detail
Interface POS2/0/0
Hardware is Packet Over SONET, One-port OC12, Single Mode Intermediate Reach
POS2/0/0
SECTION
LOF = 1 LOS = 0 BIP(B1) = 96
LINE
AIS = 0 RDI = 1 FEBE = 265 BIP(B2) = 1170
PATH
AIS = 0 RDI = 1 FEBE = 78 BIP(B3) = 51
LOP = 1
PLM-P = 1 UNEQ-P = 0
Active Alarms: None
Active Defects:None
Alarm reporting enabled for:SF SLOS SLOF B1-TCA B2-TCA PLOP B3-TCA
Framing:SONET
APS
COAPS = 25 PSBF = 1
State:PSBF_state = False
Rx(K1/K2):00/00 Tx(K1/K2):00/00
S1S0 = 00, C2 = 0x16
PATH TRACE BUFFER:STABLE
Remote hostname :acl-traffic
Remote interface:POS9/0/0
Remote IP addr :0.0.0.0
Remote Rx(K1/K2):00/00 Tx(K1/K2):00/00
61 63 6C 2D 74 72 61 66 66 69 63 00 00 00 00 00 acl-traffic.....
00 00 2F 30 00 00 00 00 50 4F 53 39 2F 30 2F 30 ../0....POS9/0/0
00 00 00 00 00 00 30 2E 30 2E 30 2E 30 00 00 00 ......0.0.0.0...
00 00 00 00 00 00 30 30 30 30 30 30 30 30 0D 0A ......00000000..
BER thresholds: SF = 10e-3 SD = 10e-6
TCA thresholds: B1 = 10e-6 B2 = 10e-6 B3 = 10e-6
Clock source: Configured:line Current:line
Last valid pointer from H1-H2: 0x20A
B1:set 564, clr 124, ber 0, err 0, lk<1eps 0/0, lk_eps 95, dly 0, set 1, clr
10
, A 0, Rd 0, R 1, D 1
B2:set 564, clr 124, ber 0, err 0, lk<1eps 0/0, lk_eps 0, dly 0, set 1, clr
10,
A 0, Rd 0, R 1, D 1
B3:set 564, clr 124, ber 0, err 0, lk<1eps 0/0, lk_eps 50, dly 0, set 1, clr
10
, A 0, Rd 0, R 1, D 1
Total number of port interrupts = 33
----- POS module IO registers -----
Starting address @0xBC280000
FPGA Revision = 0x0001
Reset Register = 0x0003
Tx/Rx LED Register = 0x0000
Alarm LED Register = 0x0000
CD LED Register = 0x0000
PLL Control Register = 0x0003
Tx Clock Config Register = 0x0000