Chapter 4 Configuring Interfaces
Configuring the ATM Uplink Interface (Catalyst 8540)
Example
The following example shows sample output for the show interfaces atm command.
Router# show interfaces atm 0/0/0 ATM0/0/0 is down, line protocol is down
Hardware is epif_port_garfield, address is 0090.2157.c407 (bia 0090.2157.c407) MTU 4470 bytes, sub MTU 4470, BW 155000 Kbit, DLY 10 usec, rely 0/255, load 1/
255
Encapsulation ATM, loopback not set, keepalive not supported
ARP type: ARPA, ARP Timeout 04:00:00
Encapsulation(s): AAL5 AAL3/4, PVC mode
8191 maximum active VCs, 1024 VCs per VP, 0 current VCCs VC idle disconnect time: 300 seconds
Last input never, output never, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 8 packets output, 2736 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Example
The following example shows sample output for the show controllers atm command.
Router# show controllers atm 0/0/0 |
|
|
|
|
|
| |||||
slot: 0/0 | OC3 PM - 1 Port SM_IR |
|
|
| |||||||
0000 | chan0 | chan1 chan2 chan3 sstr 1200 |
|
|
|
|
| ||||
task0 | 11 |
| 11 | 11 | 11 |
|
|
|
|
|
|
task1 | 5CB |
| 5CB | 5CB | 5CB |
|
|
|
|
|
|
task2 | 11 |
| 11 | 11 | 11 |
|
|
|
|
|
|
task3 | 5CB |
| 5CB | 5CB | 5CB |
|
|
|
|
|
|
SMDR 0xFF78 | SSTR 0x1200 SSMR 0x4002 EVER 0x3001 |
|
|
| |||||||
SIMR 0x0000 | MBXW 0x0000 MBXR 0x0000 SPER 0xF000 |
|
|
| |||||||
TX SAR (Beta 2.1.2) is Operational; |
|
|
|
|
|
| |||||
RX SAR (Beta 2.1.2) is Operational; |
|
|
|
|
|
| |||||
SAR Counters: |
|
|
|
|
|
|
|
| |||
| tx_paks |
| 5, tx_abort_paks |
|
| 0, tx_idle_cells | 48482684 | ||||
| rx_paks |
| 5, rx_drop_paks |
|
| 0, rx_discard_cells |
| 0 | |||
Xpif Counters: |
|
|
|
|
|
|
|
| |||
| MR1 | 580 | MR2 | 0 | MR3 | 5 | MR4 | 0 | MR5 | 0 | |
| MR6 | 0 |
| MR7 | 0 | MR8 | 0 | MR9 | 0 | MR10 0 | |
| MR11 | 0 |
| MR12 | 0 | MR13 | 5 | MR14 0 | MR15 0 | ||
| MR16 | 0 |
| MR17 | 0 | MR18 | 0 | MR19 0 | MR20 0 | ||
| MR21 | 0 |
|
|
|
|
|
|
|
|
|
| SR1 | 2500 | SR2 | 598 | SR3 | 0 | SR4 | 0 | SR5 | 0 | |
| MT1 | 560 | MT2 | 0 | MT3 | 5 | MT4 | 0 | MT5 | 0 | |
| MT6 | 0 |
| MT7 | 0 | MT8 | 0 | MT9 | 0 |
|
|
| ST1 | 0 |
| ST2 | 0 |
|
|
|
|
|
|
| MRXS | 131188 | MTXS | 112 | SRXS 3 | STXS 0 |
|
| |||
|
| Layer 3 Switching Software Feature and Configuration Guide |
|
|
|
|
|
| |||
|
|
|
| ||
|
|
|
|
