Manuals / Clarity / TV and Video / CRT Television

Clarity WN-5040-720 manual Regulatory Certifications, FCC Regulations

Models: WN-5040-720

1 152

Download 152 pages 9.83 Kb

Page 144

7.7 Regulatory Certifications

Declaration of Conformity
Manufacturer's Name:	Clarity Visual Systems
Manufacturer's Address:	27350 SW 95th Avenue, Suite 3038
	Wilsonville, OR 97070-7708
declares that the products
Model Numbers:	WN-5040-720 (DLP™ projector)
Product Options:	All

conforms to the following EU Directives and the standards stated:

Safety:

UL60950 - Safety of IT Equipment

Electromagnetic Compatibility Directive 89/336/EEC and amendments

EN 55022/CISPR 22 – Radiate and Conducted Emissions from IT Equipment

EN 50082-1/EN61000-4 – Generic Immunity Standard

Including: EN61000-4-2Electrostatic Discharge

EN61000-4-3Radiated Susceptibility

EN61000-4-4Electrical Fast Transient Burst

EN61000-4-5Surge

EN61000-4-6Conducted Susceptibility

EN610004-11Voltage Dips & Interrupts

FCC Regulations

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interfer- ence in an installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate receiving antenna.

•Increase separation between equipment and receiver.

•Connect equipment to an outlet on a circuit different from that to which the receiver is connected.

•Consult your dealer or an experienced radio/TV technician.

Note: Any changes or modifications to the display not expressly approved by Clarity Visual could void the user's authority to operate this equipment. Use of a shielded interface cable is required to comply with the Class A lim- its of Part 15 of FCC rules.

Other Certifications

UL, CUL, FCC/CISPR 22/85, CE

134

Image 144

Clarity WN-5040-720 manual Regulatory Certifications, FCC Regulations

Contents

User Guide Page User Guide Margay Display Wall UnitPage Iii Page Feedback About Manuals Page Contents Troubleshooting … Basic Information About Margay Accessories For Margay Check what you received with the Margays Short side-to-side bolt DVI cable VGA cable Remote Control Your Safety and Margay’s Safety Page Page Installing Installation ConfigurationWhat You Will Do Page Installing the VIM Video Input Module One of 4 screws Installing the Big Picture Key Page Why is straight so important? Building the Wall, First RowLaying the first row Page Building the Wall, Second Row and Up Continuing to build the wall Safety with high or tilted walls Screens when inverted Building a Banner, Upside DownInverting the picture and menus Page Connections Page Digital Out connector carries the selected input Connections, Analog & Digital SourcesLimits of loop-thru Out Video is a option installed in the field Connections, Video SourcesComposite video VideoPage Connections, Power AC loop-thru means you won’t need as many mains sockets AC power in and out Connections, Control RS232 & RS485 Connect to the computerPage Installing and Removing Screens About no-mullion screensAvoiding damage to the screens Avoiding gaps between screens Dont do this Installing the Screens Final adjustmentFirst ThenPage Opening or Removing a Screen HintsSteps to remove a single screen from a Margay wall Then this edge Opening a Screen Temporarily for Work Margay screen props open for work from the front Aligning and Adjusting Adjusting Margay’s Engine Important Step Aligning the optical engineWhat if you CAN’T move the image enough? Loosen these two nuts Page Alignment Dashes Adjusting Each Margay To Its Source How does Input Level relate to Color BalanceSelecting the source What does Input Level do?Page Adjusting to Computers, Analog RGB Best way to adjust levels is the semi-automatic methodPage Adjusting Input Levels Manually Adjusting levels manuallyPage Adjusting to Computer Sources, Digital Page Adjusting to Video Sources Adjusting the pictureAdjusting with any picture Adjusting with color bars Saturation Match Color Balancing a Wall of Margays Color Balancing can be done before or after Input LevelsColor Balancing Set White Boost to Off Set Test Pattern to White Brightness Using an external processor Using Clarity’s Big PictureSpreading One Picture Over a Wall Scale Mode, Justify and Border Color…Page Scaling and Cropping No Big Picture key Zoom and Position Page Viewport Adjustment Viewport menus adjust the image on the DMDWhat is the DMD? What is Viewport?Page How to recall a memory slot Saving Your Work & Recalling a MemoryHow automatic save works Manually saving to memory slots Enter Memory What Is Saved? And Where? Switching modesMemory Switching input connectors Possible issue with Input specific memoryGlobal parameters Memory slotsPage Operating Selecting a Source Page Normal Start Up Start up sequenceShut down sequence Page Remote control Controlling Margay with RemoteBeeper If the remote doesn’t workPage Controlling Margay with RS232/RS485 Connect the RS232 In to the computer. Loop thru with RS485Page Asset Tag and Display Status Display Status menu information Troubleshooting Troubleshooting Tips Margay has several troubleshooting aidsPage Reading the On Screen Code Turning on the On Screen codeAutomatic On Screen code display Margay On-Screen Codes Reading the LEDs To see LEDs LEDs in Margay Page Maintenance for Margay When should I change the lamp? How to change the lamp from the frontChanging a Lamp You can change the lamp from the front or the rear Resetting lamp hours How to maintain lamp lifeRemoving the lamp from the rear Replacing the lamp Clean, cool air is essential for proper Margay operation When should I change the air filter?Changing the Air Filter Removing the air filter from the front Removing the air filter from the rear Cleaning the Screen and Mirrors Reference Section Menu Trees … Menu Trees Picture Picture Source Select Input Levels Analog Sources Input Levels Digital Sources Input Levels Video Sources Size & Position Size & Position Aspect Ratio & Wall Memory Memory Recall Memory Save Diagnostics Display Status Diagnostics RS232 & RS485 Status Diagnostics Test Patterns Diagnostics Setup Summary Diagnostics Hours Advanced Options Color Balance Advanced Options Miscellaneous Options Advanced Options Lamp Settings Advanced Options Serial Port Settings Advanced Options Auto Setup Options Advanced Options Engine Alignment Advanced Options Menu Options Program Information Remote Control Buttons Page Page Page All dimensions are in inches Drawings 121 122 123 Connector Diagrams RS232 adapter DB15 standard VGA connector Video connector DVI-I connector Glossary of Terms Term Meaning See also YPbPr VIM 129 Specifications for Margay Mechanical Specification Maximum Minimum Typical Optical Specification Maximum Minimum Typical Environmental Specification Maximum Minimum Typical 133 Regulatory Certifications FCC Regulations Index 136 137 138 C D 140 Describe the problem My Clarity Reseller isBut first Un-helpful language