Dont do this | Clarity WN-5040-720 instruction

When Margays are installed in a row, the screens are very close together.

Pulling a screen from the outside of the row causes it to bind with its neighbor.

View fromabove a row of Margays


	Top of Margay 1			Top of Margay 2			Top of Margay 3

	Screen 1			Screen 2			Screen 3

Top of Margay 1

Top of Margay 2

Top of Margay 3

Screen 1

Screen 2

Pulling a screen

from the outside edge. ouch

DON'T DO THIS!

The proper way is to make the first pull on the neighboring edge of an outside row.


	Top of Margay 1			Top of Margay 2

	Screen 1			Screen 2

Top of Margay 3

Screen 3

Pull the inside edge of the column first, but just a little.

Then pull the outer edge to release all the spring latches.


	Top of Margay 1			Top of Margay 2


	Screen 1			Screen 2

Top of Margay 3

Screen 3

Then pull the outer edge.

31

Image 41

Clarity WN-5040-720 manual Dont do this

Contents

User Guide Page Margay Display Wall Unit User GuidePage Iii Page Feedback About Manuals Page Contents Troubleshooting … Basic Information About Margay Check what you received with the Margays Accessories For Margay Short side-to-side bolt DVI cable VGA cable Remote Control Your Safety and Margay’s Safety Page Page Installing What You Will Do InstallationConfiguration Page Installing the VIM Video Input Module One of 4 screws Installing the Big Picture Key Page Laying the first row Why is straight so important?Building the Wall, First Row Page Continuing to build the wall Building the Wall, Second Row and Up Safety with high or tilted walls Inverting the picture and menus Screens when invertedBuilding a Banner, Upside Down Page Connections Page Limits of loop-thru Digital Out connector carries the selected inputConnections, Analog & Digital Sources Out Connections, Video Sources Video is a option installed in the fieldComposite video VideoPage AC loop-thru means you won’t need as many mains sockets Connections, Power AC power in and out Connect to the computer Connections, Control RS232 & RS485Page About no-mullion screens Installing and Removing ScreensAvoiding damage to the screens Avoiding gaps between screens Dont do this Final adjustment Installing the ScreensFirst ThenPage Steps to remove a single screen from a Margay wall Opening or Removing a ScreenHints Then this edge Margay screen props open for work from the front Opening a Screen Temporarily for Work Aligning and Adjusting What if you CAN’T move the image enough? Adjusting Margay’s Engine Important StepAligning the optical engine Loosen these two nuts Page Alignment Dashes How does Input Level relate to Color Balance Adjusting Each Margay To Its SourceSelecting the source What does Input Level do?Page Best way to adjust levels is the semi-automatic method Adjusting to Computers, Analog RGBPage Adjusting levels manually Adjusting Input Levels ManuallyPage Adjusting to Computer Sources, Digital Page Adjusting the picture Adjusting to Video SourcesAdjusting with any picture Adjusting with color bars Saturation Match Color Balancing can be done before or after Input Levels Color Balancing a Wall of MargaysColor Balancing Set White Boost to Off Set Test Pattern to White Brightness Using Clarity’s Big Picture Using an external processorSpreading One Picture Over a Wall Scale Mode, Justify and Border Color…Page Scaling and Cropping No Big Picture key Zoom and Position Page Viewport menus adjust the image on the DMD Viewport AdjustmentWhat is the DMD? What is Viewport?Page Saving Your Work & Recalling a Memory How to recall a memory slotHow automatic save works Manually saving to memory slots Enter Memory Memory What Is Saved? And Where?Switching modes Possible issue with Input specific memory Switching input connectorsGlobal parameters Memory slotsPage Operating Selecting a Source Page Shut down sequence Normal Start UpStart up sequence Page Controlling Margay with Remote Remote controlBeeper If the remote doesn’t workPage Connect the RS232 In to the computer. Loop thru with RS485 Controlling Margay with RS232/RS485Page Display Status menu information Asset Tag and Display Status Troubleshooting Margay has several troubleshooting aids Troubleshooting TipsPage Automatic On Screen code display Reading the On Screen CodeTurning on the On Screen code Margay On-Screen Codes To see LEDs Reading the LEDs LEDs in Margay Page Maintenance for Margay How to change the lamp from the front When should I change the lamp?Changing a Lamp You can change the lamp from the front or the rear How to maintain lamp life Resetting lamp hoursRemoving the lamp from the rear Replacing the lamp When should I change the air filter? Clean, cool air is essential for proper Margay operationChanging the Air Filter Removing the air filter from the front Removing the air filter from the rear Cleaning the Screen and Mirrors Menu Trees … Reference Section Picture Menu Trees Picture Source Select Input Levels Analog Sources Input Levels Digital Sources Input Levels Video Sources Size & Position Size & Position Aspect Ratio & Wall Memory Memory Recall Memory Save Diagnostics Display Status Diagnostics RS232 & RS485 Status Diagnostics Test Patterns Diagnostics Setup Summary Diagnostics Hours Advanced Options Color Balance Advanced Options Miscellaneous Options Advanced Options Lamp Settings Advanced Options Serial Port Settings Advanced Options Auto Setup Options Advanced Options Engine Alignment Advanced Options Menu Options Program Information Remote Control Buttons Page Page Page Drawings All dimensions are in inches 121 122 123 RS232 adapter DB15 standard VGA connector Connector Diagrams DVI-I connector Video connector Term Meaning Glossary of Terms See also YPbPr VIM 129 Mechanical Specification Maximum Minimum Typical Specifications for Margay Optical Specification Maximum Minimum Typical Environmental Specification Maximum Minimum Typical 133 FCC Regulations Regulatory Certifications Index 136 137 138 C D 140 My Clarity Reseller is Describe the problemBut first Un-helpful language