This parameter is set to 1Hz | Cypress CY4672 manual

Bridge

5.3.2.1Global Configuration

The following is a description of the Global Resources that are configured for the PRoC LP CYRF69213. Be very careful when modifying these values as they affect the User Modules dis- cussed below.

CPU Clock

This parameter is set to Internal (24 MHz). In order to run the CPU at 12 MHz CPU Clock/N needs to be set to ‘2’. This operating frequency provides for faster code execution.

CPU Clock / N

This parameter is set to ‘2’ to provide a 12 MHz clock.

Timer Clock

This parameter is set to FreeRun Timer.

Timer Clock /N

This parameter is set to ‘4’.

Sleep Timer

This parameter is set to 1_Hz.

FreeRun Timer

This parameter is set to Low Power (32 kHz).

FreeRun Timer /N

This parameter is set to ‘6’.

Capture Edge

This parameter is set to Latest.

8 Bit Capture Prescaler

This parameter is set to ‘1’.

USB Clock

This parameter is set to Internal (24 MHz).

USB Clock /2

This parameter is set to Enable.

CLKOUT Source

This parameter is set to Internal (24 MHz).

Low V Detect

This parameter is set to 4.44 – 4.53 V.

V Reset

This parameter is set to 3.3V.

80	CY4672 Reference Design Guide, Document # 001-16968 Revision **

[+] Feedback

Image 80

Cypress CY4672 manual This parameter is set to 1Hz, This parameter is set to 4.44 4.53

Contents

CY4672 Reference Design Guide Copyrights Disclaimer Contents 2.3 Programmable Interval Timer User Module 2.4 2.12.2 4.1 9.3 9.19.2 2.4 1 Millisecond Interval Timer User Module 2.5 6.166.17 6.18 1.1 1.21.3 100 105 107108 109 Introduction ScopeChapter Overviews Support Acronyms ConventionsDefinitions Rssi Introduction WirelessUSB Protocol General OverviewRadio Channel Management Pseudo Noise Codes Chip Error Correction Automatic Acknowledgment AutoACKNetwork ID Manufacturing ID Protocol Modes Channel Selection Algorithm Ping Mode Bridge Only Idle ModeBind Mode Reconnect KISSBind Mode Button Bind Mode Idle Mode HID onlyReconnect Mode HID only Enhanced KISSBind Slave Back Channel Data Support Data ModeUnbind Back Channel Transaction Sequence Dynamic Data Rate and Dynamic PA Dynamic Data Rate Packet Structures Bind/KISSBind Request Packet HID Bind Response Packet Bridge Connect Request HIDConnect Response Packet Bridge Device Type Data Byte 0-N This is byte-aligned application data Ping Packet BridgeData Packet/Back Channel Data Packet Bridge and HID Bind and Reconnect Timing Bind Timing Diagram Signature Byte Device TEA Encryption TEA Key Management over WirelessUSBEncryption AES Encryption TEA Encryption Key Management Encryption and Power Consumption Trade Off AES Key Management WirelessUSB Protocol Design Features RDK Mouse AssemblyMouse Introduction Bottom View Bind Button and On-Off Switch Hardware Block Diagram Schematics PRoC LP Device Configuration Firmware ArchitectureHardware Considerations 1 ROM/RAM Usage CYRF69103 Device Architecture Global Configuration SPI Master User Module Flash Security Programmable Interval Timer User ModuleModel Common Code Generated Library CodeDebounce Module SPI Module Timer Module Radio DriverProtocol Module Flash Module Mouse Module Application CodeISR Module Optical Module Testmode Module Wheel Module Buttons ModuleMfgtest Module Configuration Options Battery Module Platformh MOUSE800NOT400CPIMfgtestcode Mfgtxmodes Wireless Protocol Data Payload Platform and Architecture PortabilityInitialization Kissbind Interrupt usage and timing Packet Format9.2 Packet Format Byte Tools Development EnvironmentCode Performance Analysis Watchdog Timer Tips and TricksCritical Test Points 2.1 M8C Sleep Keyboard RDK Keyboard Assembly Keyboard Plastic Radio and PSoC Board PDC-9265 Schematic Bind Button Keyboard Matrix Row Build Option ROM Usage RAM Usage Bytes EnCoRe II Device ConfigurationTotal ROM Total RAM Bytes Microcontroller Device Architecture This parameter is set to Enable This parameter is set to DisableThis parameter is set to Tcap This parameter is set to ‘1’ Reset Application TimerIsr Keyboard Module Test Module Keyboardkeepalivetimeout Encrypt Module Encryptaes TimercalEncrypttea Mouseemulationmode Keyboard Application Report Formats Byte Name 0xFCModifier Reserved Scan Code Keys 0x00 0x04 Modifier Reserved Scan Code Keys 0x00 Application Report Power Key Scan Ghost Key Detection Interrupt Usage / Timing Code Performance Analysis Modifying the Keyboard Matrix or Adding New Keys Modifying the Keyboard MatrixAdding New Keys Build the firmware, the new key ‘My Computer’ will work RDK Keyboard with POD Installed 10. RDK Keyboard Test Points Bridge Bridge Photographs In-System Programming Schematics LED Usage RDK Bridge with USB Adapter and PSoC MiniProg Total ROM Bytes Total RAM Bytes Build Option ROM Usage Bytes RAM Usage Bytes CYRF69213 Device Architecture This parameter is set to 1Hz This parameter is set to 4.44 4.53 2.4 1 Millisecond Interval Timer User Module USB Device User Module PSoC Generated Library Code Modules consist of the common code logical grouping Timer FlashMaster Protocol Bridge Module USB Module Mfgtestcode Powerbind Dalenable Suspend and Remote Wakeup Interrupt Usage/TimingPolling method is used for the Bind button Parameter Icc Units USB Interface USB Descriptors Device/Config Descriptors Keyboard HID Report Descriptor Mouse/Keyboard HID Report Descriptor Keyboard HID Report Descriptor Endpoint Bridge Keyboard power keys use Report ID Keyboard Report Format Keyboard Endpoint EP1 Reserved Standard Key Wheel Battery Level and Link Quality Reports Mouse Report FormatMouse Endpoint EP2 Report ID Unused Usage ID Usage Name Requesting a New Battery Reading Obtaining the RadioParams Report Example USB Bus Analyzer Catc Traces 17. Example keyboard Catc Trace Standard and MM Keys 18. Example Mouse Catc Trace 19. Example Keyboard Catc Trace Power Key Key Up Development and Debug Environment Few of ways for working with the kit are the following MTK Serial Protocol MTK Block DiagramManufacturing Test Support, MTK Serial Response Protocol Serial Command ProtocolCommand Command Description Accessing MTK in the DUT Serial Port Parameter SettingsMTK RF Protocol MTK DUT Source Code Porting Manufacturing Test Support, MTK Regulatory Testing Results Test Parameter FCC Limit Measured Value Margin Regulatory Testing Results Power Considerations Operation Mode Icc mA with Average Icc Supply Voltage =RDK Keyboard Usage Model RDK Mouse Battery Life CalculationsMode Hrs/day Days Average Icc mA Charge mAh Active mode-Move the mouse in a circle on white Paper Power Considerations USB HID API module Software GuideSoftware Code Modules Method Type Description CHidDevice Class MethodsCHidDeviceClass Methods CHidManager Class Methods CHidManagerClass Methods CCySysTray Methods System Tray ModuleCCySysTray Class Methods WirelessUSB System Tray Application Module CWirelessUSBTrayApp Class Methods OnStopTimer Public This method stops the timer OnTimer CMainFrame Class Methods CWirelessUSBStatusPropertyPage Class Methods CWirelessUSBStatusPropertySheet Class Methods CHidTrayDevice Class Methods CHidTrayManager Class Methods Appendix A. References + Feedback Index Numerics LED Pseudo noise codes 13, 14 PSoC Designer generated files Index Revision History + Feedback