Chapter | Datamax DGL instruction

Chapter 2

F(1): EAN-13

G(1): EAN-8

H(1): Health Industry Barcode (HBIC) (Code 39 barcode with a modulo 43 checksum)

I(1): Codabar

J(1): Interleaved 2 of 5 with a modulo 10 checksum

K(1): Plessey (See Partially Supported Commands)

L(1): Interleaved 2 of 5 with a modulo 10 checksum and shipping bearer bars

M(1): 2-digit UPC addendum

N(1): 5-digit UPC addendum

O(1): Code 93

P: Postnet

Q(1): UCC/EAN Code 128 (See Partially Supported Commands)

R(1): UCC/EAN Code128 K-MART NON EDI barcode. (See Partially Supported Commands)

S(1): UCC/EAN Code 128 Random Weight (See Partially Supported Commands)

T(1): Telepen

u: UPS MaxiCode (Modes 2&3) (See Partially Supported Commands)

U:UPS MaxiCode (Modes 2&3) with Byte Count Specifier (See Partially Supported Commands)

v: FIM

Z: PDF-417

Z:PDF-417 with Byte Count Specifier W1c: DataMatrix

W1C: DataMatrix with Byte Count Specifier

W1f: Aztec

W1f: Aztec with Byte Count

W1g and W1G: USD-8 (Code 11)

W1k: RSS (six types) (See Partially Supported Commands)

W1R(1): UCC/EAN Code 128 K-Mart NON EDI barcode (alternate type) (See Partially Supported Commands)

(1)These barcodes print human readable interpretation when uppercase ID is specified. Lowercase prints barcode without HR.

26

Image 26

Datamax DGL manual Chapter

Contents

Printer Protocol Interpreter PPI DGL Page Page Trademark Acknowledgments Copyright 2006 PRINTRONIX, INC Table of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup Menu Character Set PPI/DGL Setup SubmenuActive Control Codes Default ModuleEuro Character Feedback Chars Column Offset Error HandlingRow Offset Format Attrib Soft Switch Vertical DPI AdjustCommand Ignore Menus Length Cmd STXc STX B Get Printer Time and Date Information STX a Enable Feedback CharactersSTX a Set Time and Date STX c Set Continuous Paper Length STX F Form Feed STX K Extended-System CommandsSTX L Enter Label-Formatting Command STX G Print Last Label Format STX n Set Printer to Imperial Inches STX U Label Format Field ReplacementSTX m Set Printer To Metric STX o Cycle Cutter STX y Select Font Symbol Set STX V Software SettingsSTX X Set Default Module STX v Print Firmware Version Information Set Count by Amount + Make Last Field Entered Increment Numeric AlphanumericMake Last Field Entered Decrement Numeric Alphanumeric Set Format Attribute Advanced Font Attributes Terminate Label Formatting Mode and Print LabelSet Dot Size Width and Height FSn Points Set Inch Mode Imperial Enter Heat SettingSet Metric Mode Set Print Speed Set Slew Rate Terminate Label-Formatting ModeSelect Font Symbol Set Store Label Format In Module ESC *c###D Assign Font ID Number STX S Recall Global Data And Place In FieldSTX T Print Time and Date ESC s###W Font Descriptor Chapter SOH C Stop/Cancel SOH # ResetSOH *- Reset SOH a Send Ascii Status String STX Kc Configuration Set SOH U Update System Database with Current DatabaseSTX KC Get Configuration STX Kd Set File as Factory Default STX Kq Query Memory Configuration new format STX KF Select Factory DefaultsSTX KQ Query Memory Configuration STX Kr Resettable Counter Reset STX KM Configure Internal Memory Module Size STX Kb Backfeed Time DelaySTX KD Database Configuration STX KR Reset Memory Configuration STX T Printhead Dot Pattern Test Label STX P Character HEX Dump Mode STX p Controlled PauseSTX R Ribbon Saver On/Off STX t Test RAM Memory Module STX d Set Printer to double buffer mode STX b Set Cutter signal timeSTX D Memory Dump Test Mode Only STX g Internal Batch Software Mode Wait mode Prodigy only Select Mirror ModeSet Label Backup Speed Zip Mode Prodigy only Fonts DPI Internal Bitmapped Non-Proportional fonts Slash Zero ISmooth, Scalable and Downloaded fonts Valid Ascii Characters for bitmap fonts CodepagesResident Bitmap Fonts Scalable Fonts Barcode Symbologies PostNet UCC/EAN CodePlessey MaxiCode Flash / Ram Module compatibility ImagesGraphics Supported graphics objects Image Formats Module Operations Cutter CommandsBi-Directional Communications Ignored Commands Printer ConfigurationCommand Reference Emulations Workaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description ENABLED, *DISABLED TRANSPARENT, *XOR Opaque Imaging ModePause Mode Peel Mode Host Settings ENABLED, *DISABLED Menu LanguageFault Handling Level Host Timeout Description PTX Setting Communications Menu Datamax Setting Description PTX SettingDiagnostics Menu Contact Information Corporate Offices Appendix B Corporate OfficesPage 250103-001