Datamax Setting Description PTX Setting | Datamax DGL specs

Appendix A

Table 3. Printer Options Menu

Datamax Setting	Description	PTX Setting

CUTTER	Used to cut media into	MEDIA CONTROL → Media
	separate labels.	HandlingCut
	ENABLED, *DISABLED, NOT
	INSTALLED
SCANNER	Used to check the bar codes	VALIDATOR menu
	on the labels.
GPIO PORT	Model dependant option used	GPIO CONTROL menu and
	to interface the printer to an	GPIO Manager
	external controlling device.

	Table 4. System Settings Menu

Datamax Setting	Description	PTX Setting

CONFIGURATION FILE	Options for storage and recall
	of printer configuration files.
RESTORE AS CURRENT	Provides a list of available	CONFIG CONTROL → Load
	configuration files. Selecting a	Config
	file from the list causes a
	printer reset; afterward, the
	printer is configured
	according to the activated file.
SAVE SETTING AS	Saves the entire effective	CONFIG CONTROL → Save
	configuration of the printer to	Config
	a file.
DELETE FILE	Provides a list of available	CONFIG CONTROL →
	configuration files to delete.	Delete Config
FACTORY SETTING FILE	The selected file will be	CONFIG CONTROL →
	restored whenever a Level 1	Power-Up Config
	reset is performed.
INTERNAL MODULE	Sets the number of 1K blocks	N/A
	allocated for the internal RAM
	‘D’ module.
	*1024 KB
DEFAULT MODULE	Sets the default module used	PPI/DGL SETUP → Default
	to store files when no other	Module
	module is specified.*D	*RAM, Flash

48

Image 48

Datamax DGL manual Datamax Setting Description PTX Setting

Contents

Printer Protocol Interpreter PPI DGL Page Page Trademark Acknowledgments Copyright 2006 PRINTRONIX, INC Table of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup Menu PPI/DGL Setup Submenu ActiveCharacter Set Default Module Euro CharacterControl Codes Feedback Chars Error Handling Row OffsetColumn Offset Format Attrib Vertical DPI Adjust Command Ignore MenusSoft Switch Length Cmd STXc STX a Enable Feedback Characters STX a Set Time and DateSTX B Get Printer Time and Date Information STX c Set Continuous Paper Length STX K Extended-System Commands STX L Enter Label-Formatting CommandSTX F Form Feed STX G Print Last Label Format STX U Label Format Field Replacement STX m Set Printer To MetricSTX n Set Printer to Imperial Inches STX o Cycle Cutter STX V Software Settings STX X Set Default ModuleSTX y Select Font Symbol Set STX v Print Firmware Version Information + Make Last Field Entered Increment Numeric Alphanumeric Make Last Field Entered Decrement Numeric AlphanumericSet Count by Amount Set Format Attribute Terminate Label Formatting Mode and Print Label Set Dot Size Width and HeightAdvanced Font Attributes FSn Points Enter Heat Setting Set Metric ModeSet Inch Mode Imperial Set Print Speed Terminate Label-Formatting Mode Select Font Symbol SetSet Slew Rate Store Label Format In Module STX S Recall Global Data And Place In Field STX T Print Time and DateESC *c###D Assign Font ID Number ESC s###W Font Descriptor Chapter SOH # Reset SOH *- ResetSOH C Stop/Cancel SOH a Send Ascii Status String SOH U Update System Database with Current Database STX KC Get ConfigurationSTX Kc Configuration Set STX Kd Set File as Factory Default STX KF Select Factory Defaults STX KQ Query Memory ConfigurationSTX Kq Query Memory Configuration new format STX Kr Resettable Counter Reset STX Kb Backfeed Time Delay STX KD Database ConfigurationSTX KM Configure Internal Memory Module Size STX KR Reset Memory Configuration STX P Character HEX Dump Mode STX p Controlled Pause STX R Ribbon Saver On/OffSTX T Printhead Dot Pattern Test Label STX t Test RAM Memory Module STX b Set Cutter signal time STX D Memory Dump Test Mode OnlySTX d Set Printer to double buffer mode STX g Internal Batch Software Mode Select Mirror Mode Set Label Backup SpeedWait mode Prodigy only Zip Mode Prodigy only Fonts DPI Internal Bitmapped Non-Proportional fonts Slash Zero ISmooth, Scalable and Downloaded fonts Codepages Resident Bitmap FontsValid Ascii Characters for bitmap fonts Scalable Fonts Barcode Symbologies UCC/EAN Code PlesseyPostNet MaxiCode Images Graphics Supported graphics objectsFlash / Ram Module compatibility Image Formats Cutter Commands Bi-Directional CommunicationsModule Operations Printer Configuration Command ReferenceIgnored Commands Emulations Workaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description TRANSPARENT, *XOR Opaque Imaging Mode Pause ModeENABLED, *DISABLED Peel Mode ENABLED, *DISABLED Menu Language Fault Handling LevelHost Settings Host Timeout Communications Menu Datamax Setting Description PTX Setting Diagnostics MenuDescription PTX Setting Contact Information Corporate Offices Appendix B Corporate OfficesPage 250103-001