Trademark Acknowledgments | Datamax DGL guide

Trademark Acknowledgments

DPL is a trademark and Datamax is a registered trademark of Datamax Technologies Corporation.

PPI is a trademark of Printronix, Inc.

Printronix and PSA are registered trademarks of Printronix, Inc.

COPYRIGHT © 2006 PRINTRONIX, INC.

All rights reserved.

Image 4

Datamax DGL manual Trademark Acknowledgments, Copyright 2006 PRINTRONIX, INC

Contents

Printer Protocol Interpreter PPI DGL Page Page Trademark Acknowledgments Copyright 2006 PRINTRONIX, INC Table of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup Menu Active PPI/DGL Setup SubmenuCharacter Set Default Module Euro CharacterControl Codes Feedback Chars Error Handling Row OffsetColumn Offset Format Attrib Vertical DPI Adjust Command Ignore MenusSoft Switch Length Cmd STXc STX a Enable Feedback Characters STX a Set Time and DateSTX B Get Printer Time and Date Information STX c Set Continuous Paper Length STX K Extended-System Commands STX L Enter Label-Formatting CommandSTX F Form Feed STX G Print Last Label Format STX U Label Format Field Replacement STX m Set Printer To MetricSTX n Set Printer to Imperial Inches STX o Cycle Cutter STX V Software Settings STX X Set Default ModuleSTX y Select Font Symbol Set STX v Print Firmware Version Information + Make Last Field Entered Increment Numeric Alphanumeric Make Last Field Entered Decrement Numeric AlphanumericSet Count by Amount Set Format Attribute Terminate Label Formatting Mode and Print Label Set Dot Size Width and HeightAdvanced Font Attributes FSn Points Enter Heat Setting Set Metric ModeSet Inch Mode Imperial Set Print Speed Terminate Label-Formatting Mode Select Font Symbol SetSet Slew Rate Store Label Format In Module STX S Recall Global Data And Place In Field STX T Print Time and DateESC *c###D Assign Font ID Number ESC s###W Font Descriptor Chapter SOH # Reset SOH *- ResetSOH C Stop/Cancel SOH a Send Ascii Status String SOH U Update System Database with Current Database STX KC Get ConfigurationSTX Kc Configuration Set STX Kd Set File as Factory Default STX KF Select Factory Defaults STX KQ Query Memory ConfigurationSTX Kq Query Memory Configuration new format STX Kr Resettable Counter Reset STX Kb Backfeed Time Delay STX KD Database ConfigurationSTX KM Configure Internal Memory Module Size STX KR Reset Memory Configuration STX P Character HEX Dump Mode STX p Controlled Pause STX R Ribbon Saver On/OffSTX T Printhead Dot Pattern Test Label STX t Test RAM Memory Module STX b Set Cutter signal time STX D Memory Dump Test Mode OnlySTX d Set Printer to double buffer mode STX g Internal Batch Software Mode Select Mirror Mode Set Label Backup SpeedWait mode Prodigy only Zip Mode Prodigy only Fonts DPI Internal Bitmapped Non-Proportional fonts Slash Zero ISmooth, Scalable and Downloaded fonts Codepages Resident Bitmap FontsValid Ascii Characters for bitmap fonts Scalable Fonts Barcode Symbologies UCC/EAN Code PlesseyPostNet MaxiCode Images Graphics Supported graphics objectsFlash / Ram Module compatibility Image Formats Bi-Directional Communications Cutter CommandsModule Operations Printer Configuration Command ReferenceIgnored Commands Emulations Workaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description TRANSPARENT, *XOR Opaque Imaging Mode Pause ModeENABLED, *DISABLED Peel Mode ENABLED, *DISABLED Menu Language Fault Handling LevelHost Settings Host Timeout Diagnostics Menu Communications Menu Datamax Setting Description PTX SettingDescription PTX Setting Contact Information Corporate Offices Appendix B Corporate OfficesPage 250103-001