Dell 610 manual Qvwdoolqjdq,+Duglvnulyh, Ulyh$Gguhvvlqj, Vxuidfh

,QVWDOOLQJ￿DQ￿(,'(￿+DUG￿'LVN￿'ULYH

This section includes information on installing, partitioning, and formatting EIDE hard- disk drives. For instructions on installing, partitioning, and formatting SCSI hard-disk drives, see “Installing SCSI Devices” found later in this chapter.

Up to four 1-inch or up to two 1-inch and two 1.6-inch EIDE drives can be installed in the internal hard-disk drive cage below the externally accessible 5.25-inch drive bays.

(,'(￿'ULYH￿$GGUHVVLQJ

All EIDE devices should be configured for the cable select jumper position, which assigns master and slave status to devices by their position on the EIDE cable. When two EIDE devices are connected to a single EIDE cable and are configured for the cable select jumper position, the device attached to the last connector on the inter- face cable is the master or boot device (drive 0) and the device attached to the middle connector on the interface cable is the slave device (drive 1). Refer to the drive docu- mentation in your upgrade kit for information on setting devices to the cable select jumper position.

With the two EIDE interface connectors on the system board, your system can sup-

GPDJHEHWKHGULYH￿,QV	VHWWKHGULYH	VXUIDFH￿	DVDIRDP
port up to four EIDE devices. EI	hard-disk drives should be connected to the EIDE

interface connector labeled “IDE1.” (EIDE tape drives and CD-ROM drives should be connected to the EIDE interface connector labeled “IDE2.”)

,QV DOOLQJ￿DQ￿(,'(￿+DU 'LVN￿'ULYH￿LQ￿WKH￿,QWHUQ O￿ +DUG￿'LVN￿'ULY ￿& JH

￿￿￿￿InstallWKLV:KHQRQ&,I\RXNHHS3UHSDUH$an87,216WKHSURFHGXUHEI￿DUH\RXEDFNWKHVXUHWRhardUHSODFLQJXQSDFN￿*URXQGRIGULYH-disk￿WKHPDNHdriveIRUWKHFRPSXW\RXVHOILQVWDODWLRQKDUGGULYinHDGtheEDFNXSFXVKLRQ￿￿U￿GLVNhardGRE\WRXFKLQJQRW-diskGULYHRI\RXU￿VHWdriveWKDWLWILOHVDQRQbracketFRQWDLQVXQSDLQWHGEHIRUHKDUGas follows:VXUIDHGDWD\RXVXFKPHWDOFRQWLQXHZLWK\RXZDQW￿ZKLFKVXUIDFHPD\WR

SDG￿WKDWZLOOVXIILFLHQO\ LW￿

Check the documentation that accompanied the drive to verify that it is config-

￿￿&LQVWUXFWLRQV5HPRYHured$RYHUµ87,21for yourWKH￿&KDSWHU6HHcomputerDWWKHIURQWFRPSXWHU¥3RWHFWLQJ￿￿systemFRYHURIWKLV$.JDLQVWDVJXLGHLQVWUXFWHG(OHFWURVWDWLF￿ LQ¥5HPRYLQJ'LVFKDUJHµWKHLQWKH&RPSXWHUVDIHW\

Installing Drives 10-11