Battery Cabinet Precautions | Emerson 250-400kVA specification

BATTERY CABINET PRECAUTIONS

The following warning applies to all battery cabinets supplied with UPS systems. Additional warn- ings and cautions applicable to battery cabinets may be found in Important Safety Instructions and 3.4 - Battery Maintenance.

! WARNING

Internal battery strapping must be verified by manufacturer prior to moving a battery cabinet (after initial installation).

•Battery cabinets contain non-spillable batteries.

•Keep units upright.

•Do not stack.

•Do not tilt.

Failure to heed this warning could result in smoke, fire or electric hazard. Call 1-800-LIEBERT before moving battery cabinets (after initial installation).

Contacting Liebert for Support

Contact Emerson Network Power Liebert Services for information or repair service in the United States at 1-800-LIEBERT (1-800-543-2378).

For repair or maintenance service outside the 48 contiguous United States, contact Liebert Services, if available in your area. For areas not covered by Liebert Services, the authorized distributor is responsible for providing qualified, factory-authorized service.

Have the following information available before calling Liebert Services:

Part Numbers: ________________________________________________________________

Serial Numbers: _______________________________________________________________

kVA Rating: __________________________________________________________________

Date Purchased: _______________________________________________________________

Date Installed: ________________________________________________________________

Location: _____________________________________________________________________

Input Voltage/Frequency: ______________________________________________________

Output Voltage/Frequency: _____________________________________________________

Battery Reserve Time: _________________________________________________________

Image 2

Emerson 250-400kVA manual Battery Cabinet Precautions, Contacting Liebert for Support

Contents

Liebert NXL Battery Cabinet Precautions Contacting Liebert for Support Table of Contents Specifications Figures Page Important Safety Instructions Modes of Operation Normal ModeGeneral Description Maintenance Bypass Bypass ModeBattery Mode Options Introduction Features Main component locations Mimic display Monitor/mimic display example Normal power flow Monitor/mimic display example Utility fail Monitor/mimic display example Load on bypass, UPS On Touchscreen Navigation Main Display Screen Menu tree Configurations Menu Rating Rating Parameters User Settings System Settings parameters Adjustable Setpoints Adjustable setpoints parameters Cell Count Adjustment Startup Menu Event ManagementStatus Reports Menu Shutdown Menu Shutdown menu Transfer/retransfer commands Transfer Menu Battery Management Menu Time remaining display Display summary see Figure Help ResetMetering Silence OK to Transfer Load on bypass, UPS available Input Power Failure-Load on Battery Input power fail, load on battery Off Battery Emergency Module Off Manual Procedures Remote Emergency Power Off Startup Procedure Startup commands Re-Transfer Procedure Load Transfer ProceduresTransfer Procedure Maintenance Bypass Load Transfers Maintenance Bypass Load Transfers-If Load is on UPS Bypass System Shutdown Procedure Shutdown ProceduresUPS Shutdown Procedure Automatic Operations Automatic Transfers to Bypass Overload Condition Current-versus-time curves of overload capacity Automatic Transfers to Bypass, UPS System Faults Automatic Retransfers to UPS Safety Precautions Liebert Services Routine Maintenance Record Log Air Filters Limited Life Components Battery MaintenanceUPS component service life Component Expected Life Replace Battery Safety Precautions Battery retorque values Matching Battery Cabinets-OptionalBattery voltage, nominal and float Rack-Mounted Batteries Torque specifications, unless otherwise labeledDetecting Trouble Torque Requirements Corrective Actions Reporting a ProblemUpstream Feeder Circuit Breaker Setting Inspections Parameter Specification Battery OperationEnvironmental specifications Environmental Conditions Liebert NXL Model Size 250 Electrical specificationsBattery & DC Parameters Input Parameters Physical Parameters & Standards, in mm Liebert NXL Model SizeSystem Parameter Specifications Liebert NXL alarm and status messages Event Message Event Definition Recommended Action Observe the One-Line Display. If the input line is Observe the One-Line Display. To identify which Do not Attempt to Close CB3 Until Reset Displayed on the Module Output Meter. If UPS controls monitor the DC Bus positive Resolve the issue that precipitated the EPO Check the One-Line Display for system status UPS, to transfer back to Inverter If this alarm occurs on an operational unit, it Attempt to manually close the disconnect by Module Output Meter. If the load is less than Output Power Factor. If the displayed power factor Until a service visit has been made and action taken When manual transfers are enabled Under normal conditions, no user action is required Observe the One-Line Display and the Active Event If the command to terminate Regeneration Mode If the alarm cannot be reset, or if the alarm condition UPS Alarm and Status Messages UPS Alarm and Status Messages Page Ti n Ne tIti That