Mimic display | Emerson 250-400kVA specification

Operation

Figure 3 Main Display Screen, typical

Mimic

Display

		Multipurpose
		Display
	Active
	Event	Menu
	Window	Menu
	Window	Bar
		Bar

Figure 4

Mimic display

Bypass

BYPASS

A

B

C

Input

L-L

0

0

0

V

BFB

Freq

0.0Hz

UPS

INPUT

DC BUS

A

B

C

Input

L-L

0

0

0

V

Voltage

0V

Power

I

0

0

0

A

CB1

Current

Float

Freq

0.0Hz

Battery

BATTERY1 OF 4

T

Block

Voltage Disable

Temp

Disable

BIS1

MBD

CB2

MODULE OUTPUT

	A	B	C
L-L	0	0	0	V
L-N	0	0	0	V
I	0	0	0	A
KVA	0	0	0	%
KW	0	0	0	%
PF	0.0	0.0	0.0
KVA/KW		0/	0
Freq		0.0Hz
Rexfer Timeout			00:00

Legend

Inlet Air Temp 0°C

Load

Bypass Input—Displays the bypass input voltage and the bypass input frequency. The bypass cir- cuit breaker (BFB) is to the right of this block. The circuit breaker status is shown as open or closed.

UPS Input Power—Displays the UPS input voltage, current and frequency. The input circuit breaker (CB1) is to the right of this block. The circuit breaker status is shown as open or closed.

Battery Block—Displays the battery voltage and the charge or discharge current to or from the bat- tery. Pressing this icon switches among the connected battery strings. The Module Battery Discon- nect (MBD) is to the right of this block. The circuit breaker status is shown as open or closed.

DC Bus—Displays the DC Bus voltage and the state of the battery charger.

Load—Displays the output line voltage, phase voltage, current, kVA, kW, power factor and fre- quency. The critical load current per phase is also displayed in this block. During an overload, the time remaining before transfer is displayed at the bottom of the load box. After an overload transfer, retransfer timeout is displayed at the bottom of the load box.

6

Image 12

Emerson 250-400kVA manual Mimic display

Contents

Liebert NXL Battery Cabinet Precautions Contacting Liebert for Support Table of Contents Specifications Figures Page Important Safety Instructions Normal Mode General DescriptionModes of Operation Bypass Mode Battery ModeMaintenance Bypass Options Introduction Features Main component locations Mimic display Monitor/mimic display example Normal power flow Monitor/mimic display example Utility fail Monitor/mimic display example Load on bypass, UPS On Touchscreen Navigation Main Display Screen Menu tree Configurations Menu Rating Rating Parameters User Settings System Settings parameters Adjustable Setpoints Adjustable setpoints parameters Cell Count Adjustment Event Management Status Reports MenuStartup Menu Shutdown Menu Shutdown menu Transfer/retransfer commands Transfer Menu Battery Management Menu Time remaining display Display summary see Figure Reset MeteringHelp Silence OK to Transfer Load on bypass, UPS available Input Power Failure-Load on Battery Input power fail, load on battery Off Battery Emergency Module Off Manual Procedures Remote Emergency Power Off Startup Procedure Startup commands Load Transfer Procedures Transfer ProcedureRe-Transfer Procedure Maintenance Bypass Load Transfers Maintenance Bypass Load Transfers-If Load is on UPS Bypass Shutdown Procedures UPS Shutdown ProcedureSystem Shutdown Procedure Automatic Operations Automatic Transfers to Bypass Overload Condition Current-versus-time curves of overload capacity Automatic Transfers to Bypass, UPS System Faults Automatic Retransfers to UPS Safety Precautions Liebert Services Routine Maintenance Record Log Air Filters Battery Maintenance UPS component service lifeLimited Life Components Component Expected Life Replace Battery Safety Precautions Matching Battery Cabinets-Optional Battery voltage, nominal and floatBattery retorque values Torque specifications, unless otherwise labeled Detecting TroubleRack-Mounted Batteries Torque Requirements Reporting a Problem Upstream Feeder Circuit Breaker Setting InspectionsCorrective Actions Battery Operation Environmental specificationsParameter Specification Environmental Conditions Electrical specifications Battery & DC ParametersLiebert NXL Model Size 250 Input Parameters Liebert NXL Model Size System ParameterPhysical Parameters & Standards, in mm Specifications Liebert NXL alarm and status messages Event Message Event Definition Recommended Action Observe the One-Line Display. If the input line is Observe the One-Line Display. To identify which Do not Attempt to Close CB3 Until Reset Displayed on the Module Output Meter. If UPS controls monitor the DC Bus positive Resolve the issue that precipitated the EPO Check the One-Line Display for system status UPS, to transfer back to Inverter If this alarm occurs on an operational unit, it Attempt to manually close the disconnect by Module Output Meter. If the load is less than Output Power Factor. If the displayed power factor Until a service visit has been made and action taken When manual transfers are enabled Under normal conditions, no user action is required Observe the One-Line Display and the Active Event If the command to terminate Regeneration Mode If the alarm cannot be reset, or if the alarm condition UPS Alarm and Status Messages UPS Alarm and Status Messages Page Ne t ItiTi n That