Emerson 250-400kVA manual Observe the One-Line Display. To identify which

			UPS Alarm and Status Messages
Table 7	Liebert NXL alarm and status messages (continued)
Event Message		Event Definition	Recommended Action
			Press “SILENCE” to silence the audible alarm.
			Observe the One-Line Display. To identify which
			battery cabinet is reporting the temperature
			condition, press the “Battery Box” on the One-Line
			Display to cycle through each battery compartment
		One or more of the Battery Temperature Sensors	or string. The temperature display is located under
			the voltage reading in the Battery Box.
		is reporting a temperature above the limit	If the Common Battery Disconnect and/or the
		setpoint.
			individual battery cabinet or string reporting the over
		There are two user-adjustable Battery
			temperature condition is tripped, check the following
		Temperature Setpoints: Battery Over
			settings.
		Temperature Warning and Battery
Batt Ovtemp Limit			Press “User Settings,” “Battery Management,”
		Overtemperature Limit. The temperature in one or
			“Battery Temperature” to check the current Battery
		more battery compartments has risen above the	Temperature Setpoints. If none of the Battery Boxes
		limit setpoint.
			on the One-Line Display exhibit a temperature in
		Depending on user settings, the controls may trip
			excess of the temperature setpoint in the user
		the battery breaker associated with the over	settings, contact your factory-authorized service
		temperature condition.
			provider.
			If the overtemperature limit is being reported
			correctly, investigate potential causes such as faulty
			air conditioning, or air flow blockage and resolve.
			Otherwise, contact your factory-authorized service
			provider.
			Press “SILENCE” to silence the audible alarm.
			Observe the One-Line Display. To identify which
			battery cabinet is reporting the temperature
		One or more of the Battery Temperature Sensors	condition, press the “Battery Box” on the One-Line
		is reporting a temperature above the warning	Display to cycle through each battery compartment
			or string. The temperature display is located under
		setpoint.
			the voltage reading in the Battery Box.
		There are two user adjustable Battery
			Press “User Settings,” “Battery Management,”
		Temperature Setpoints: Battery Over
			“Battery Temperature” to check the current Battery
Batt Ovtemp		Temperature Warning and Battery
			Temperature Setpoints. If none of the Battery Boxes
Warning		Overtemperature Limit. This alarm means the
			on the One-Line Display exhibit a temperature in
		temperature in one or more battery compartments
			excess of the temperature setpoint in the user
		has risen above the warning setpoint.	settings, contact your factory-authorized service
		This alarm is self-clearing. When the condition is
			provider.
		no longer present, the alarm and any control
			If the overtemperature warning is being reported
		activity tied to the alarm reverts to normal
			correctly, investigate potential causes, such as
			faulty air conditioning or air flow blockage and
			resolve. Otherwise, contact your factory-authorized
			service provider.
		The UPS is performing a battery self test.
		The battery self test terminates automatically at
		the end of the test.	During normal operation, no user response is
		Battery test settings are adjustable and can be
			required.
		accessed by pressing “Config,” “User Settings,”
Batt Self Test			The battery test can be terminated at any time by
		“Batt Mgt,” “Battery Test.”
			the user by pressing “Batt Mgt,” “Manual Battery
		This status message is self-clearing. When the
			Test,” “Stop.”
		condition is no longer present, the message and
		any control activity tied to the status event reverts
		to normal.
		The controls are sensing a failed Battery	Press “SILENCE” to silence the audible alarm.
		Temperature Sensor.
		If a sensor reports a value outside the normal	Try to identify which sensor has failed by observing
Batt Sensor Fail		operating range of the sensor, it is considered	the temperature reading inside the Battery Box on
		failed.	the One-Line Display. Cycle through all connected
		This alarm is self-clearing. When the condition is	batteries by pressing the Battery Box on the display.
		no longer present, the alarm and any control	Contact your factory-authorized service provider.
		activity tied to the alarm reverts to normal.

45