Signal Name, Bit Selection Jumper, Pin Signal | Emerson CC1000DM

Signal Name:

BRIDGE_SEE_EN*

	S E T U P	.
	S E T U P	.
	CC1000dm Setup	.
	CC1000dm Setup	.
		.
		. .

	Bit:		Selection:	(continued)		Jumper:
	0		Bridge serial ROM enabled (default)			Remove 9-10



	1		Bridge serial ROM disabled			Install 9-10

Mode Selection (JP5) The system controller modes are selected by jumper JP5. The legacy product is the Arte- syn CC1000 carrier card.

Jumper Position:

Table 2-3:

Mode_Sel (3:0):

Mode:

	System Controller Modes,	1-2	1000	Non-Transparent (default)
	JP5	1-2	1000	Non-Transparent (default)

		3-4	1011	Transparent
		3-4	1011	Transparent

		2-4	0001	Legacy (CC1000)

		None	1001	No System Controller

PLD Header (JP6) This 10-pin JTAG header is used by the PLD.

Figure 2-6:		10
PLD Header, JP6	2
	2
		9
		1
	Pin:	Signal:	Pin:	Signal:
Table 2-4:
PLD Header Pin Assignments,	1	PLD_TCK	2	ground
JP6
	3	PLD_TDO	4	PLD_3_3V
	5	PLD_TMS	6	no connect
	7	no connect	8	no connect
	9	PLD_TDI	10	ground

10004281-02

CC1000dm User’s Manual 2-9

Image 27

Emerson CC1000DM user manual Signal Name, Bit Selection Jumper, Jumper Position ModeSel, Pin Signal

Contents

CC1000dm Revision Level Principal Changes Date Regulatory Agency Warnings & Notices EC Declaration of Conformity Contents Bridge Eeprom PCI Bridge Features PMC Module Installation Figures G u r e s Tables Ta b l e s Registers G i s t e r s Overview Functional Overview N. .C.T.I.O. N. .A. L. . O. .V.E. R. .V.I.E.W Type Specification Product CertificationRoHS Compliance Device / Interface Document Terminology and NotationTechnical References Additional Information Document 6CC1000dm User’s Manual 10004281-02 Width Depth Setup Component Map, Top rev CC1000dm Circuit Board CC1000dm Circuit Board Identification Numbers Connectors Fuses and Jumpers Jumper/Header Locations, Top View Multiple Option Selection JP3 CC1000dm Setup Signal Name Bit Selection CC1000dm Setup Jumper Position ModeSel Signal NamePin Signal Bit Selection Jumper Typical Current Voltage Range Amps Power RequirementsEnvironmental Considerations Operational Checks S. E. .T. .M. E. .T.H. O. .D.S Non-transparent Reset Methods O. U. .B. L. E. .S.H. O. .O. T. I. N. .G Troubleshooting 14CC1000dm User’s Manual 10004281-02 PMC/PCI Interface Volts PMC Module InstallationDevice Mapping C / P C I I N T E R F a C E Interrupt System controller modes Base cPCI Interrupt Transparent Mode Assignment SecondaryTiming Interrupts Base PCI Internal Arbiter Control Register CC1000dm Request/Grant Local PCI Bus Device Bridge Eeprom I.D. G. .E. .E.E. P. .R.O. M PCI 6254 Configuration Registers Power Management CSR PCI 6254 Configuration Registers 38h Reserved Status PCI 6254 Bridge Mode PCI Identification ValuesVendor Device Subsystem ID hex I. .B.U. S. . C. .O. N. .T.R. O. .L. .S.I.G. N. .A.L. S PCI Bus Control Signals PCI Bus Control Signals Pin J11 J12 J13 J14 PMC Connector Pin Assignments J23 J24 Pin J21 J22 Pin J11J13 J14 Pin J11 J12 Pin J21 Pin J21 J22 J23 J24 Carrier Card BUS Interface Arbitration and Device Selection O. C. .K. .G. E. .N. E. R. .A.T. I.O. .N Model Description Hot Swap Hot Swap Implementation CC1000dm Control Signals Signal DescriptionPin Row Z Row a Row B Row C Row D Row E Row F Pin Row Z Row a Row B Row C Row D Row E Backplane Connector Pin Assignments Pin Row a Row B Row C Row D Row E Row F Row F Pin Row a Row B Row C Row D Row E Backplane Connector Pin Assignments 10CC1000dm User’s Manual 10004281-02 PrPMC CPCI O s s a r y Index D e Page W. a r t e s y n c p . c o m