Serial Channel, Available Options 8-bit or 7-bit | Epson 60 specification

ADJUSTING THE PRINTER SETTINGS

8.Press or until the required setting is dis - played.

9. Store the displayed setting:

10. four times to return to printer "Ready" mode.

- Serial Channel -

There are nine settings for the serial channel. These settings must match the settings that your computer’s serial channel is using. Check your computer’s manual for this in - formation.

❐WORD LENGTH: This specifies how many bits there are between the start and stop bits.

Available Options: 8-bit or 7-bit.

❐BAUDRATE: This allows you to set the data transfer rate for the serial channel.

Available Options: 300, 600, 1200, 2400, 4800, 9600, 19200

❐PARITY: Parity is a basic form of error detection.

Available Options: ODD, EVEN, NONE. If you select NONE, there is no parity check.

❐STOP BIT: Use this to select the number of stop bits that are sent to the printer with each character to signal the end of a character.

Available Options: 1 or 2

❐DTR: Use this to turn the printer’s DTR (Data Terminal Ready) communications pro - tocol on or off. You can use DTR protocol in combination with the XON/XOFF option setting.

❐XON/XOFF: Use this to turn the printer’s XON/XOFF communications protocol on or off. You can use DTR protocol in combination with the DTR option setting .

❐ENQ/ACK: Not used. Keep OFF.

❐DSR: When DSR (Data Set Ready) is OFF, the DSR signal is permanently set to HIGH, allowing the printer to send data to the computer. For most communication purposes, this option should be kept OFF. When DSR is ON, data is sent to the com - puter only when the DSR signal is HIGH .

❐CTS: When CTS (Clear To Send) is OFF, the CTS signal is permanently set to HIGH. For most communication purposes, this option should be kept OFF. When CTS is ON, data is sent to the computer only when the CTS signal is HIGH .

Factory Settings
WORD LENGTH: 8-bit	BAUDRATE: 9600
PARITY: NONE	STOP BIT: 2
DTR: ON	XON/XOFF: ON
ENQ/ACK: OFF	DSR: OFF
CTS: OFF

36

Image 42

Epson 60 manual Serial Channel, Available Options 8-bit or 7-bit, Available Options 1 or

Contents

Printer Interface Type OPERATOR’S Manual Page Contents Selectype Level 2 Features Selectype Level 1 FeaturesSave Macro Load Macro Poweron Macro Delete Macro Test Print Mode Assign Using Selectype Mode to Adjust the HP Emulation Mode Table of SpecificationsHP Emulation Mode VS HP Laserjet Available Fonts and Symbol Sets Font Cards and Emulation Mode Cards Using Selectype Mode to Adjust Epson LQ and FX EmulationLQ and FX Emulation Command Summary Operating AS AN LQ or FX Printer Introduction About the Printer Interface Introduction Conventions About this Manual Operation Panel Buttons Indicators Display Installation Installing the Interface KITConnection to the Computer Testing the Printer Printing a Test For full information about macros See pages 31 to Optional Kits Memory Expansion Board Optional Font and Emulation Mode Cards Optional Font Cartridges Connecting the Printer to TWO Computers Multi-user Modes Basic Operations Turning the Printer on Line and OFF LineForm Feed Resetting the Printer Selecting the Cassette for Computer Printing Selecting the Emulation Mode HP Laserjet III Emulation ModeOverview Changing the Emulation Mode Using the Mode Assign FeatureEpson LQ and FX Emulation Modes Using an Emulation Control Language Epson Job Language EJL Either ESC SOH@EJL Enter LANGUAGE=LJ-3REM Copy HP.TXT LPT1 Close Printer Job Language Adjusting the Printer Settings Introduction Level 2 Features Using Selectype Mode Display Sample Selectype Procedure Display the required setting for this feature Selectype Level 1 Features Copies InputSize Available Options 1 to Font SUB ConfigOrient Status Sheet System Config Full Print Paper Size Setting Memory LeftOffset and L-OFFSET Save Macro Load Macro Poweron Macro Delete Macro Mode Assign Selectype Level 2 FeaturesHow to Enter Selectype Level Test Print CONFIG. Interface Configuration Parallel ChannelAvailable Options ON, OFF Serial Channel Available Options 8-bit or 7-bitAvailable Options 1 or RX-BUFFER Size Receive Buffer Size CH Channel If you selected Autosense If you selected Individual CH Timeout Channel Timeout Config Save Power-up Configuration Auto Cont Auto Continue Factory Reset Version Counter Standby Change PCU Solving ProblemsStatus and Error Messages Char Creating Graphic Drawing Feed JAMFont Creating Initialize Reinsert Card Paper Size ErrorPrinting Remove Card Toner LOW Startup ErrorSET Full Print Toner OUT Printing Problems On-line/off-line indicator is offPaper OUT or Toner OUT is displayed Some or all of the output is garbled or printed as asterisks Problems with Graphics You cannot print graphics using the serial channel Problems with Selectype Mode Desired Selectype settings are not displayed Problems with Optional Cards and Cartridges Data Dump Mode ESC R Appendix A. Specifications Appendix B. HP Emulation Mode HP Emulation Modevs HP LaserjetPrintable Area Paper Handling Fonts Font name in HP emulation modeCharacter Clipping Downloaded Fonts Symbol Sets Esc # Esc s#P Esc s#B Esc s#S Esc s#T Operating AS a Laserjet IIISi Using Selectype Mode to Adjust the HP Emulation Mode Orient Page Orientation Appendix B. HP Emulation Mode Available Options 0 to Attribute Bitmap Scalable Available Fonts and Symbol SetsFont Name Spacing Height Typeface Style Weight Resident Bitmap Fonts Font Name Symbol Set Height pt Typeface Style Weight Resident Scalable Fonts Appendix B. HP Emulation Mode IBM-US 10U IBM-DN 11U PcMultilingual 12U Legal 1U ISO Ansi Ascii 0U Ventura International 13J Ventura US 14J PS Math 5M PS Text 10J Math-8 8M Pi Font 15U Microsoft Publishing 6J Windows 9U Desktop 7J Ve Zapf Dingbats 9L Ps Zapf Dingbats 10L Zd 100 11L Zd 200 12L Zd 300 13L HP Emulation Command Summary Orientation Printer commands arranged by topicControl codes Font selection ESC9K ESC2KESC8K ESC0L Length, page size, text length MarginsOffset Half-line feed Perforation skip modeVertical line spacing Specialized printer control Push/Pop position Font managementMacros Raster graphics Line and fill attributes group GL/2 mode Configuration and status groupVector graphics Vector group Appendix C. Epson LQ and FX Emulation Modes Operating AS AN LQ or FX PrinterPaper Size Using Selectype to Adjust Epson LQ and FX Emulation Paper Size Condensed Portrait Landscape 10 cpi 12 cpi 15 cpi Appendix C. Epson LQ and FX Emulation Modes Appendix C. Epson LQ and FX Emulation Modes Font Name Pitch cpi Orientation Character Sets Pc USA Epson International Character Sets ESC G/ESC E LQ and FX Emulation Command SummaryESC U SI/ESC SI DEL CanESC EM Printer operation Data controlVertical motion Overall printing style Horizontal motionPrint position Print size and character width Character tables Word processingESC SP User-defined characters Appendix D. Optional Font Cards and Cartridges Font Cards and Emulation Mode CardsEmulation Mode Cards Font Cards Selecting a font with the Selectype Font procedure Caring for Cards Using a font card and a font cartridge at the same time When the printer is in 3/P/Si modeWhen the printer is in LQ or FX mode Using the Epson GL Emulation Mode Card Recovering from a Card Error Font CartridgesAvailable Font Cartridges Maker Cartridge Number Recovering from a cartridge error Appendix E. List of Features Level Test Print Si Emulation Mode JIS ASC Epson LQ or FX Emulation Mode Appendix F. Connector PIN Configuration Parallel Interface Pin Number Signal NameSerial Interface Pin Number Signal Name Pin assignments for typical ATs and compatibles Appendix G. Status Sheet Following is an example of a status sheet printout