Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MCJ3230SS manual 44 Sense Key, 45 Logical track address format

Models: MCJ3230SS

1 161

Download 161 pages 59.65 Kb

Page 102

Table 4.44 Sense Key

Host Interface

			Table 4.44 Sense Key

	Sense	Mnemonic	Meaning
	Key	Mnemonic	Meaning
	Key
	0h	NO SENSE	There is no sense key to be reported. NO SENSE is set when
			a command ends normally.

	1h	RECOVERED	Recovery processing ended successfully or the commands
		ERROR	ended normally using the internal default values even though
			invalid data was detected in command parameters. (This sense
			data is not reported if the PER bit is 0.)

	2h	NOT READY	No access commands can be used.
	3h	MEDIUM	An unrecoverable error due to media failure was detected.
		ERROR
	4h	HARDWARE	An unrecoverable error due to hardware failure was detected.
		ERROR

	5h	ILLEGAL	A command packet or command parameter contains invalid
		REQUEST	data; media data remains unchanged.

	6h	UNIT	Reset state, power-on, or media replacement was caused.
		ATTENTION
	7h	DATA	Media is write-protected with the write-protect switch or with
		PROTECT	software.

	8h	BLANK CHECK	A blank sector was detected. This sense key is reserved.
	9h-	Reserved	Reserved
	Ah
	Bh	ABORTED	Processing of the command was interrupted.
		COMMAND

	Ch-	Reserved	Reserved
	Fh

Information indicates the LBA of the block in which an error occurred. If errors occur in multiple blocks, Information indicates the LBA of the block in which the first error occurred.

Command-Specific Information indicates the logical track address of the block indicated by Information. The format of the logical track address is shown in Table 4.45.

Table 4.45 Logical track address format

Byte

8-9

10

11

Description

Logical track address

00h

Logical sector address

Additional Sense Code (ASC) and Additional Sense Code Qualifier (ASCQ) indicate detailed error information. Table 4.46 lists the ASC and ASCQ definitions.

4-28	C156-E224-01EN

Image 102

Fujitsu MCJ3230SS manual 44 Sense Key, 45 Logical track address format

Contents

MCJ3230SS OPTICAL DISK DRIVE PRODUCT MANUAL C156-E224-01ENFOR SAFE OPERATION Handling of This ManualRevision History This page is intentionally left blank Chapter 5 Diagnostics and Maintenance Chapter 2 SpecificationsChapter 3 Installation Requirements Chapter 6 Diagnostics and MaintenanceGlossary CONVENTIONS USED IN THIS MANUALConventions for Alert Messages Acronyms and AbbreviationsExample DISCLAIMER C156-E224-01ENImportant Alert Messages Low temperature burnsImportant Alert Items Device damageDamage for disk medium Device DamageDamage for data medium Eye inflammation4. HOST INTERFACE 5. OPERATION AND CLEANING This manual OPTICAL DISK DRIVES MAINTENANCE MANUAL C156-F0431. GENERAL DESCRIPTION 2. SPECIFICATIONS 3. INSTALLATION REQUIREMENTS 6. DIAGNOSTICS AND MAINTENANCE 1. MAINTENANCE AND DIAGNOSISREFERENCED STANDARDS Preface ContentsSpecifications DISCLAIMEROperation Confirmation and Preparation for Use after Installation Installation RequirementsContents CHAPTERCHAPTER 4 Host Interface 4.3.10 PREVENT/ALLOW MEDIUM REMOVAL commandSYNCHRONIZE CACHE command 5.3.3 How to affix an index label on the MO cartridge CHAPTER 5 Operation and CleaningCHAPTER 6 Diagnosis and Maintenance Optical Disk Cartridge OperationAbbreviations Glossary……………………………………………………………………….GL-1 …….…………………………………………………………………AB-1Illustrations FiguresC156-E224-01EN Revision labelRevision number indication Tables Variable values in the read-write error recovery pageDefault values in the read-write error recovery page Defect list header of READ DEFECT DATA 10 command PREVENT/ALLOW MEDIUM REMOVAL commandDefect List Format of READ DEFECT DATA 10 command RECEIVE DIAGNOSTIC RESULTS commandThis page is intentionally left blank CHAPTER 1 General Description 1.1 Features 1.1.1 Performance1.1.2 Reliability 1.1 Features1.1.3 Maintainability/operability 1.1.4 Adaptability1.1.5 Interface 6 Defective block slipping 1.2 Drive Configuration 1.2.1 Drive modelFigure 1.1 Outer view with panel Figure 1.2 Outer view without panel 1.2.2 Configuration Figure 1.3 Optical disk drive configuration1.2.3 Mechanical sections Figure 1.4 Control circuit section block diagram 1.2.4 Control circuit section1.2 Drive Configuration C156-E224-01EN1-11 This page is intentionally left blank 2.1.1 Model and product number CHAPTER 2 Specifications2.1 Optical Disk Drive Specifications Table 2.1 Model and order number2.1.2 Drive specifications Table 2.2 Specifications 1 ofTable 2.2 Specifications 2 of 2.1 Optical Disk Drive Specifications2.1.3 Environmental and power requirements Table 2.3 Environmental and power requirements 1 ofTable 2.3 Environmental and power requirements 2 of 2.1.4 Error rate 2.1.5 Reliability2.2 Optical Disk Cartridge Specifications 2.2.1 Recommended optical disk cartridge specificationsTable 2.5 Recommended optical disk cartridge specifications 2.2.2 Optical disk cartridge Figure 2.1 Optical disk cartridge2.2.3 Disk specifications Table 2.6 Disk specifications 2.3.1 Defect management schematic diagram 2.3 Defect ManagementFigure 2.2 Algorithms for alternate processing Figure 2.3 Example of alternate processing 2-12C156-E224-01EN CHAPTER 3 Installation Requirements 3.1.1 Temperature measurement point3.1 Environmental Requirements IC power amp Figure 3.1 Surface temperature measurement pointsInstallation Requirements IC controller3.1.2 Temperature requirements and measuring method Table 3.1 Temperature requirements at measurement points3.1.3 Air flow 3.1.4 Temperature rise under several conditions Table 3.2 Temperature at each measuring point Reference3.1.5 Air purity 3.2.1 External dimensions Figure 3.2 Dimensions3.2 Mounting Requirements Figure 3.3 Dimensions without panel Unit mmC156-E224-01EN 3.2.2 Installation direction Figure 3.4 Installation directions3.2.3 Centers of gravity Figure 3.5 Centers of gravity3.2.4 Notes on mounting Figure 3.6 Mounting frame structureR side Figure 3.7 Service clearanceP side Q side3.3 Power Supply Requirements Figure 3.8 Current waveform +5 VDCFigure 3.10 Location of setting terminal 3.4.1 Drive connectorsFigure 3.9 Connector and terminal locations 3.4 Cable ConnectionsFigure 3.11 Shape of setting terminal 3.4 Cable ConnectionsTable 3.3 Pin assignments 3.4.2 Cable connector specifications Table 3.4 Recommended components for connection3.4.3 Connection Modes Figure 3.12 SCSI bus connection modesC156-E224-01EN Figure 3.13 SCSI bus connection modesc. Connecting more than one optical disk drive multi-host 3-173.5.2 Setting terminal 3.5 Settings3.5.1 Default jumper settings Figure 3.14 Setting terminal CNH2Table 3.6 SCSI terminating resistor mode Table 3.7 Write cache mode setting3.5 Settings Table 3.8 Spindle motor automatic stop mode setting SHORTOPEN *1 3.6 Notes on Drive Handling 3.6 Notes on Drive HandlingDevice damage 3 Installation Figure 3.15 Packing style Single-unit packingMultiple-unit packing 3.7.2 Mounting procedure 3.7 Mounting3.7.1 Checks before mounting the drive 3.8 Cable Connections 3.8 Cable Connections3.9 Operation Confirmation and Preparation for Use after Installation 3.9.1 Confirming initial operations3.10 Dismounting Drive 3.9.2 Connection checkThis page is intentionally left blank 4.1 Interface Connector Figure 4.1 SCSI interface connector ODD sideCHAPTER 4 Host Interface Figure 4.2 SCSI interface connector cable side Host InterfaceTable 4.1 SCSI interface connector pin assignments single-ended type 4.1 Interface Connector4.2.2 Defective sector management 4.2.1 Reset response4.2 Various Processes 4.2.3 Automatic alternate sector assignment function4.2.4 Cache function 4.2.4.1 Data buffer4.2.4.2 Read cache 4.2.5 Power management function 4.2.6 Power mode4.2.4.3 MO write cache 4.2.6.3 Idle mode 4.2.6.1 Active mode4.2.6.2 Pre-idle mode 4.2.6.4 Standby modeActive Reset 4.2.6.6 Power mode transitionFigure 4.3 Power mode Idle4.2.7 LED indications Table 4.2 LED indications4.3 SCSI Commands Table 4.3 SCSI commandsTable 4.5 INQUIRY command 4.3.1 TEST UNIT READY commandTable 4.4 TEST UNIT READY command 4.3.2 INQUIRYTable 4.6 INQUIRY command response data LinkedCmdQue Table 4.7 READ CAPACITY command 4.3.3 READ CAPACITY command4.3.4 MODE SELECT command Table 4.9 MODE SELECT commandTable 4.10 Mode page codes Table 4.11 Mode parameter listTable 4.12 Mode parameter header Table 4.14 Mode page Table 4.15 Read/write error recovery pageTable 4.13 Block descriptor Table 4.16 Variable values in the read-write error recovery page Default values in the read-write error recovery pageTable 4.18 Flexible disk page Variable values in the flexible disk page Default values in the flexible disk pageTable 4.22 Variable values in the Caching Page Table 4.24 Power condition pageTable 4.21 Caching page Table 4.23 Default values in the Caching PageTable 4.25 Variable values in the Power condition page Table 4.26 Default values in the Power condition pageVerify control page Table 4.28 Verify mode Default values in the Verify control pageVariable values in the Verify control page 4.3.5 MODE SENSE command Table 4.31 MODE SENSE commandPage control field Table 4.33 Mode parameters Table 4.34 Mode Parameter HeaderTable 4.35 Block Descriptor Table 4.37 START/STOP UNIT command 4.3.6 START/STOP UNIT commandTable 4.36 Mode Page Table 4.38 Start, stop, and eject processing4.3.7 RESERVE command Table 4.39 RESERVE commandTable 4.40 RELEASE command 4.3.8 RELEASE command4.3.9 REQUEST SENSE command Table 4.41 REQUEST SENSE commandTable 4.43 Error Code Table 4.42 Request Sense DataReserved 00h Table 4.44 Sense Key Table 4.45 Logical track address formatTable 4.46 ASC and ASCQ definitions ASCQNOT READY TO READY TRANSITION, MEDIUM MAY HAVE Table 4.47 Format progress indication bytes 4.3.10 PREVENT/ALLOW MEDIUM REMOVAL command Table 4.48 PREVENT/ALLOW MEDIUM REMOVAL commandTable 4.49 Responses to Prevent, Allow, and Eject Table 4.50 CDB of READ 6 command 4.3.11 READ 6 command4.3.12 READ 10 command Table 4.51 READ 10 commandTable 4.52 VERIFY command 4.3.13 VERIFY command4.3.14 WRITE 6 command Table 4.53 CDB of WRITE 10 commandTable 4.55 WRITE AND VERIFY command 4.3.15 WRITE 10 commandTable 4.54 WRITE 10 command 4.3.16 WRITE AND VERIFYTable 4.56 SEEK 6 command 4.3.17 SEEK 6 command4.3.18 SEEK 10 command Table 4.57 SEEK 10 commandTable 4.58 ERASE command 4.3.19 ERASE command4.3.20 SYNCHRONIZE CACHE command Table 4.59 SYNCHRONIZE CACHE commandTable 4.61 FORMAT UNIT parameter list 4.3.21 FORMAT UNIT commandTable 4.60 FORMAT UNIT command Table 4.62 Defect List HeaderTable 4.64 Defect List Format of READ DEFECT DATA 10 command 4.3.22 READ DEFECT DATA commandTable 4.63 READ DEFECT DATA command Table 4.65 Defect list header of READ DEFECT DATA 10 commandTable 4.68 SEND DIAGNOSTIC command 4.3.23 SEND DIAGNOSTIC command4.3.24 RECEIVE DIAGNOSTIC RESULTS command Table 4.69 RECEIVE DIAGNOSTIC RESULTS command4.3.25 WRITE BUFFER command Table 4.70 WRITE BUFFER commandTable 4.71 READ LONG command 4.3.26 READ LONG command4.3.27 WRITE LONG command Table 4.72 WRITE LONG command4.4.2 Message types 4.4 SCSI Messages4.4.1 Message formats Table 4.73 Types of messages provided by ODD4.4.3 Message functions 4.4 SCSI Messages6 MESSAGE REJECT message 07h I → T Table 4.74 Transfer mode settings requested by INIT to ODD Asynchronous transferREQ/ACK Offset = Table 4.75 Timing specifications 1 of 4.5 Timing RuleTable 4.75 Timing specifications 2 of 4.5 Timing RuleTable 4.75 Timing specifications 3 of Table 4.76 FAST SCSI Timing specifications Figure 4.4 BUS FREE phaseFigure 4.5 ARBITRATION phase 4-50C156-E224-01EN Figure 4.6 SELECTION phase Figure 4.7 RESELECTION phase Figure 4.8 Transfer in asynchronous mode 4-52C156-E224-01EN Figure 4.9 Transfer in FAST SCSI mode C156-E224-01EN4-53 Figure 4.10 ATTENTION condition 4-54C156-E224-01EN CHAPTER 5 Operation and Cleaning 5.1 Operating Optical Disk Drive5.1.1 Optical disk drive Figure 5.1 Optical disk drive front view with panel5.1.2 Note 5.1.3 Inserting cartridge5.1 Operating Optical Disk Drive Figure 5.2 Inserting cartridge Inserting directionShutter 5.1.4 Ejecting removing cartridge Figure 5.3 Removing cartridge5.2 Cleaning Drive Table 5.1 Head cleaner5.3 Optical Disk Cartridge Operation 5.3.1 Optical disk cartridgeFigure 5.4 Optial disk cartridge 5.3.2 Write protect tab Figure 5.5 Write protect tab5.3.3 How to affix an index label on the MO cartridge See figure Figure 5.6 How to stick an index label on the MO cartridge5.3.4 Notes 2 When storing the cartridge Table 5.2 Cleaning kit 5.4 Cleaning Optical Disk Cartridge5.4.1 Cleaning tool Table 5.3 Packed items cleaning kit5.4.2 Cleaning procedure Figure 5.7 Cleaning procedureFigure 5.8 Cleaning procedure Figure 5.9 Cleaning procedure6 Wipe the disk surface from the hub outward Figure 5.10 Cleaning procedure7 Turn the revolving knob, then wipe the disk surface Cleaning cloth 5-146.1 Diagnosis CHAPTER 6 Diagnosis and MaintenanceTable 6.1 Self-diagnostic function 6.1.1 Initial self-diagnosis6.1.2 Diagnostic command 6.1.3 Test programDiagnosis and Maintenance 6.2 Maintenance Information 6.2.1 Maintenance requirementsData loss 6.2.2 Revision number Figure 6.1 Revision labelFigure 6.2 Revision number indication Command Axial displacementCDB Command Descriptor Block GlossaryRecording power Error correction codeError detection and correction Disk reference surfaceStatus C156-E224-01ENGL-3 This page is intentionally left blank Acronyms and Abbreviations Acronyms and Abbreviations Index ABORT messageIndex Fujitsu Internal Use OnlyRESELECTION phase sector address format service system and repairwrite cache feature SYNCHRONOUS DATA TRANSFER REQUEST message2 Julius Avenue Cnr Delhi Road North Ryde N.S.W 10/F., Lincoln House, 979 Kings Road, Taikoo Place, IslandThis page is intentionally left blank READER’S COMMENT FORM FOR FUJITSU USE