Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MCJ3230SS Device Damage, Damage for data medium, Damage for disk medium, Eye inflammation

Models: MCJ3230SS

1 161

Download 161 pages 59.65 Kb

Page 10

Device Damage:

Important Alert Items

Task	Alert message	Page

	Device damage:	3-22
	Be sure to turn on the power supply before inserting your
	cartridge for the first time. It releases the device from
	transport protection and enables you to insert the cartridge.
	The device may be damaged if you insert the cartridge
	without releasing the protection. From the next time, you
	don't need to turn on the power supply beforehand.
	Before moving the drive, remove the optical disk cartridge. If
	the drive is moved with the optical disk cartridge loaded in it,
	the head may move back and forth in the drive to damage the
	head or disk and reading the data may fail.
	• Make sure that the system power is off.	3-25
	• Do not connect or disconnect any cable when the power is
	on.
	Device damage:	3-27
	Before demounting the optical disk drive, turn off the system
	power. Do not remove screws securing the cables and drive
	when the power is on.

	Device Damage:	5-6
	Be sure to use the dedicated head cleaner described above.
	Damage for data medium:	5-12
	Do not use this cleaning kit for the floppy disk or the optical
	disk cartridge used for other optical disk drive.
	Damage for disk medium:	5-12
	Clean the cartridge at clean place. Put a disposable groves at
	cleaning so that the fingerprint does not put on the disk media
	(recommendation).
	Damage for disk medium:	5-13
	At setting the cartridge to the setting case, do not apply the
	heavy shock and push hardly.
	Eye inflammation:	5-14
	In case of contact with eyes, immediately flush eyes with
	water.
	Data loss:	6-3
	In case of regular repair, the optical disk cartridge should not
	be attached except where the cartridge causes the error. And
	before having the drive repaired, save the data in the
	cartridge. Fujitsu is not responsible for data lost during
	maintenance or repair.

vi	C156-E224-01EN

Image 10

Fujitsu MCJ3230SS manual Device Damage, Damage for data medium, Damage for disk medium, Eye inflammation, Data loss

Contents

MCJ3230SS OPTICAL DISK DRIVE PRODUCT MANUAL C156-E224-01ENFOR SAFE OPERATION Handling of This ManualRevision History This page is intentionally left blank Chapter 5 Diagnostics and Maintenance Chapter 2 SpecificationsChapter 3 Installation Requirements Chapter 6 Diagnostics and MaintenanceGlossary CONVENTIONS USED IN THIS MANUALConventions for Alert Messages Acronyms and AbbreviationsExample DISCLAIMER C156-E224-01ENImportant Alert Messages Low temperature burnsImportant Alert Items Device damageDamage for disk medium Device DamageDamage for data medium Eye inflammation4. HOST INTERFACE 5. OPERATION AND CLEANING This manual OPTICAL DISK DRIVES MAINTENANCE MANUAL C156-F0431. GENERAL DESCRIPTION 2. SPECIFICATIONS 3. INSTALLATION REQUIREMENTS 6. DIAGNOSTICS AND MAINTENANCE 1. MAINTENANCE AND DIAGNOSISREFERENCED STANDARDS Preface ContentsSpecifications DISCLAIMEROperation Confirmation and Preparation for Use after Installation Installation RequirementsContents CHAPTER4.3.10 PREVENT/ALLOW MEDIUM REMOVAL command CHAPTER 4 Host InterfaceSYNCHRONIZE CACHE command 5.3.3 How to affix an index label on the MO cartridge CHAPTER 5 Operation and CleaningCHAPTER 6 Diagnosis and Maintenance Optical Disk Cartridge OperationAbbreviations Glossary……………………………………………………………………….GL-1 …….…………………………………………………………………AB-1Illustrations FiguresRevision label C156-E224-01ENRevision number indication Variable values in the read-write error recovery page TablesDefault values in the read-write error recovery page Defect list header of READ DEFECT DATA 10 command PREVENT/ALLOW MEDIUM REMOVAL commandDefect List Format of READ DEFECT DATA 10 command RECEIVE DIAGNOSTIC RESULTS commandThis page is intentionally left blank CHAPTER 1 General Description 1.1 Features 1.1.1 Performance1.1.2 Reliability 1.1 Features1.1.3 Maintainability/operability 1.1.4 Adaptability1.1.5 Interface 6 Defective block slipping 1.2.1 Drive model 1.2 Drive ConfigurationFigure 1.1 Outer view with panel Figure 1.2 Outer view without panel 1.2.2 Configuration Figure 1.3 Optical disk drive configuration1.2.3 Mechanical sections Figure 1.4 Control circuit section block diagram 1.2.4 Control circuit sectionC156-E224-01EN 1.2 Drive Configuration1-11 This page is intentionally left blank 2.1.1 Model and product number CHAPTER 2 Specifications2.1 Optical Disk Drive Specifications Table 2.1 Model and order number2.1.2 Drive specifications Table 2.2 Specifications 1 ofTable 2.2 Specifications 2 of 2.1 Optical Disk Drive Specifications2.1.3 Environmental and power requirements Table 2.3 Environmental and power requirements 1 ofTable 2.3 Environmental and power requirements 2 of 2.1.4 Error rate 2.1.5 Reliability2.2.1 Recommended optical disk cartridge specifications 2.2 Optical Disk Cartridge SpecificationsTable 2.5 Recommended optical disk cartridge specifications 2.2.2 Optical disk cartridge Figure 2.1 Optical disk cartridge2.2.3 Disk specifications Table 2.6 Disk specifications 2.3 Defect Management 2.3.1 Defect management schematic diagramFigure 2.2 Algorithms for alternate processing 2-12 Figure 2.3 Example of alternate processingC156-E224-01EN 3.1.1 Temperature measurement point CHAPTER 3 Installation Requirements3.1 Environmental Requirements IC power amp Figure 3.1 Surface temperature measurement pointsInstallation Requirements IC controllerTable 3.1 Temperature requirements at measurement points 3.1.2 Temperature requirements and measuring method3.1.3 Air flow Table 3.2 Temperature at each measuring point Reference 3.1.4 Temperature rise under several conditions3.1.5 Air purity Figure 3.2 Dimensions 3.2.1 External dimensions3.2 Mounting Requirements Unit mm Figure 3.3 Dimensions without panelC156-E224-01EN 3.2.2 Installation direction Figure 3.4 Installation directions3.2.3 Centers of gravity Figure 3.5 Centers of gravity3.2.4 Notes on mounting Figure 3.6 Mounting frame structureR side Figure 3.7 Service clearanceP side Q side3.3 Power Supply Requirements Figure 3.8 Current waveform +5 VDCFigure 3.10 Location of setting terminal 3.4.1 Drive connectorsFigure 3.9 Connector and terminal locations 3.4 Cable ConnectionsFigure 3.11 Shape of setting terminal 3.4 Cable ConnectionsTable 3.3 Pin assignments 3.4.2 Cable connector specifications Table 3.4 Recommended components for connection3.4.3 Connection Modes Figure 3.12 SCSI bus connection modesC156-E224-01EN Figure 3.13 SCSI bus connection modesc. Connecting more than one optical disk drive multi-host 3-173.5.2 Setting terminal 3.5 Settings3.5.1 Default jumper settings Figure 3.14 Setting terminal CNH2Table 3.7 Write cache mode setting Table 3.6 SCSI terminating resistor mode3.5 Settings SHORT Table 3.8 Spindle motor automatic stop mode settingOPEN *1 3.6 Notes on Drive Handling 3.6 Notes on Drive HandlingDevice damage 3 Installation Single-unit packing Figure 3.15 Packing styleMultiple-unit packing 3.7 Mounting 3.7.2 Mounting procedure3.7.1 Checks before mounting the drive 3.8 Cable Connections 3.8 Cable Connections3.9 Operation Confirmation and Preparation for Use after Installation 3.9.1 Confirming initial operations3.10 Dismounting Drive 3.9.2 Connection checkThis page is intentionally left blank Figure 4.1 SCSI interface connector ODD side 4.1 Interface ConnectorCHAPTER 4 Host Interface Figure 4.2 SCSI interface connector cable side Host InterfaceTable 4.1 SCSI interface connector pin assignments single-ended type 4.1 Interface Connector4.2.2 Defective sector management 4.2.1 Reset response4.2 Various Processes 4.2.3 Automatic alternate sector assignment function4.2.4.1 Data buffer 4.2.4 Cache function4.2.4.2 Read cache 4.2.6 Power mode 4.2.5 Power management function4.2.4.3 MO write cache 4.2.6.3 Idle mode 4.2.6.1 Active mode4.2.6.2 Pre-idle mode 4.2.6.4 Standby modeActive Reset 4.2.6.6 Power mode transitionFigure 4.3 Power mode Idle4.2.7 LED indications Table 4.2 LED indications4.3 SCSI Commands Table 4.3 SCSI commandsTable 4.5 INQUIRY command 4.3.1 TEST UNIT READY commandTable 4.4 TEST UNIT READY command 4.3.2 INQUIRYLinked Table 4.6 INQUIRY command response dataCmdQue Table 4.7 READ CAPACITY command 4.3.3 READ CAPACITY command4.3.4 MODE SELECT command Table 4.9 MODE SELECT commandTable 4.11 Mode parameter list Table 4.10 Mode page codesTable 4.12 Mode parameter header Table 4.15 Read/write error recovery page Table 4.14 Mode pageTable 4.13 Block descriptor Table 4.16 Variable values in the read-write error recovery page Default values in the read-write error recovery pageTable 4.18 Flexible disk page Variable values in the flexible disk page Default values in the flexible disk pageTable 4.22 Variable values in the Caching Page Table 4.24 Power condition pageTable 4.21 Caching page Table 4.23 Default values in the Caching PageTable 4.26 Default values in the Power condition page Table 4.25 Variable values in the Power condition pageVerify control page Default values in the Verify control page Table 4.28 Verify modeVariable values in the Verify control page Table 4.31 MODE SENSE command 4.3.5 MODE SENSE commandPage control field Table 4.34 Mode Parameter Header Table 4.33 Mode parametersTable 4.35 Block Descriptor Table 4.37 START/STOP UNIT command 4.3.6 START/STOP UNIT commandTable 4.36 Mode Page Table 4.38 Start, stop, and eject processing4.3.7 RESERVE command Table 4.39 RESERVE commandTable 4.40 RELEASE command 4.3.8 RELEASE command4.3.9 REQUEST SENSE command Table 4.41 REQUEST SENSE commandTable 4.42 Request Sense Data Table 4.43 Error CodeReserved 00h Table 4.44 Sense Key Table 4.45 Logical track address formatASCQ Table 4.46 ASC and ASCQ definitionsNOT READY TO READY TRANSITION, MEDIUM MAY HAVE Table 4.47 Format progress indication bytes Table 4.48 PREVENT/ALLOW MEDIUM REMOVAL command 4.3.10 PREVENT/ALLOW MEDIUM REMOVAL commandTable 4.49 Responses to Prevent, Allow, and Eject Table 4.50 CDB of READ 6 command 4.3.11 READ 6 command4.3.12 READ 10 command Table 4.51 READ 10 commandTable 4.52 VERIFY command 4.3.13 VERIFY command4.3.14 WRITE 6 command Table 4.53 CDB of WRITE 10 commandTable 4.55 WRITE AND VERIFY command 4.3.15 WRITE 10 commandTable 4.54 WRITE 10 command 4.3.16 WRITE AND VERIFYTable 4.56 SEEK 6 command 4.3.17 SEEK 6 command4.3.18 SEEK 10 command Table 4.57 SEEK 10 commandTable 4.58 ERASE command 4.3.19 ERASE command4.3.20 SYNCHRONIZE CACHE command Table 4.59 SYNCHRONIZE CACHE commandTable 4.61 FORMAT UNIT parameter list 4.3.21 FORMAT UNIT commandTable 4.60 FORMAT UNIT command Table 4.62 Defect List HeaderTable 4.64 Defect List Format of READ DEFECT DATA 10 command 4.3.22 READ DEFECT DATA commandTable 4.63 READ DEFECT DATA command Table 4.65 Defect list header of READ DEFECT DATA 10 commandTable 4.68 SEND DIAGNOSTIC command 4.3.23 SEND DIAGNOSTIC command4.3.24 RECEIVE DIAGNOSTIC RESULTS command Table 4.69 RECEIVE DIAGNOSTIC RESULTS command4.3.25 WRITE BUFFER command Table 4.70 WRITE BUFFER commandTable 4.71 READ LONG command 4.3.26 READ LONG command4.3.27 WRITE LONG command Table 4.72 WRITE LONG command4.4.2 Message types 4.4 SCSI Messages4.4.1 Message formats Table 4.73 Types of messages provided by ODD4.4.3 Message functions 4.4 SCSI Messages6 MESSAGE REJECT message 07h I → T Asynchronous transfer Table 4.74 Transfer mode settings requested by INIT to ODDREQ/ACK Offset = Table 4.75 Timing specifications 1 of 4.5 Timing RuleTable 4.75 Timing specifications 2 of 4.5 Timing RuleTable 4.75 Timing specifications 3 of Table 4.76 FAST SCSI Timing specifications Figure 4.4 BUS FREE phase4-50 Figure 4.5 ARBITRATION phaseC156-E224-01EN Figure 4.6 SELECTION phase Figure 4.7 RESELECTION phase 4-52 Figure 4.8 Transfer in asynchronous modeC156-E224-01EN C156-E224-01EN Figure 4.9 Transfer in FAST SCSI mode4-53 4-54 Figure 4.10 ATTENTION conditionC156-E224-01EN CHAPTER 5 Operation and Cleaning 5.1 Operating Optical Disk Drive5.1.1 Optical disk drive Figure 5.1 Optical disk drive front view with panel5.1.3 Inserting cartridge 5.1.2 Note5.1 Operating Optical Disk Drive Inserting direction Figure 5.2 Inserting cartridgeShutter 5.1.4 Ejecting removing cartridge Figure 5.3 Removing cartridge5.2 Cleaning Drive Table 5.1 Head cleaner5.3.1 Optical disk cartridge 5.3 Optical Disk Cartridge OperationFigure 5.4 Optial disk cartridge 5.3.2 Write protect tab Figure 5.5 Write protect tabFigure 5.6 How to stick an index label on the MO cartridge 5.3.3 How to affix an index label on the MO cartridge See figure5.3.4 Notes 2 When storing the cartridge Table 5.2 Cleaning kit 5.4 Cleaning Optical Disk Cartridge5.4.1 Cleaning tool Table 5.3 Packed items cleaning kit5.4.2 Cleaning procedure Figure 5.7 Cleaning procedureFigure 5.8 Cleaning procedure Figure 5.9 Cleaning procedure6 Wipe the disk surface from the hub outward Figure 5.10 Cleaning procedure7 Turn the revolving knob, then wipe the disk surface Cleaning cloth 5-146.1 Diagnosis CHAPTER 6 Diagnosis and MaintenanceTable 6.1 Self-diagnostic function 6.1.1 Initial self-diagnosis6.1.3 Test program 6.1.2 Diagnostic commandDiagnosis and Maintenance 6.2.1 Maintenance requirements 6.2 Maintenance InformationData loss Figure 6.1 Revision label 6.2.2 Revision numberFigure 6.2 Revision number indication Command Axial displacementCDB Command Descriptor Block GlossaryRecording power Error correction codeError detection and correction Disk reference surfaceC156-E224-01EN StatusGL-3 This page is intentionally left blank Acronyms and Abbreviations Acronyms and Abbreviations Index ABORT messageIndex Fujitsu Internal Use OnlyRESELECTION phase sector address format service system and repairwrite cache feature SYNCHRONOUS DATA TRANSFER REQUEST message2 Julius Avenue Cnr Delhi Road North Ryde N.S.W 10/F., Lincoln House, 979 Kings Road, Taikoo Place, IslandThis page is intentionally left blank READER’S COMMENT FORM FOR FUJITSU USE