Initialize Device Parameters | Fujitsu MPB3021AT, MPB3054AT specs

(11)INITIALIZE DEVICE PARAMETERS (X'91')

The host system can set the number of sectors per track and the maximum head number (maximum head number is "number of heads minus 1") per cylinder with this command. Upon receipt of this command, the device sets the BSY bit of Status register and saves the parameters. Then the device clears the BSY bit and generates an interrupt.

When the SC register is specified to X'00', an ABORTED COMMAND error is posted. Other than X'00' is specified, this command terminates normally.

The parameters set by this command are retained even after reset or power save operation regardless of the setting of disabling the reverting to default setting.

In LBA mode

The device ignores the L bit specification and operates with the CHS mode specification. An accessible area of this command within head moving in the LBA mode is always within a default area. It is recommended that the host system refers the addressable user sectors (total number of sectors) in word 60 to 61 of the parameter information by the IDENTIFY DEVICE command.

At command issuance (I/O registers setting contents)

1F7H(CM)	1	0	0	1	0		0	0	1

1F6H(DH)	×	×	×	DV			Max. head No.

1F5H(CH)					xx
1F4H(CL)					xx
1F3H(SN)					xx
1F2H(SC)			Number of sectors/track
1F1H(FR)					xx

At command completion (I/O registers contents to be read)

1F7H(ST)				Status information

1F6H(DH)	×	×	×		DV		Max. head No.

1F5H(CH)						xx
1F4H(CL)						xx
1F3H(SN)						xx
1F2H(SC)						xx
1F1H(ER)				Error Information

(12)IDENTIFY DEVICE (X'EC')

The host system issues the IDENTIFY DEVICE command to read parameter information (512 bytes) from the device. Upon receipt of this command, the drive sets the BSY bit of Status register and sets required parameter information in the sector buffer. The device then sets the DRQ bit of the Status register, and generates an interrupt. After that, the host system reads the information out of the sector buffer. Table 5.5 shows the arrangements and values of the parameter words and the meaning in the buffer.

5 - 28

C141-E045-02EN

Image 93

Fujitsu MPB3021AT, MPB3054AT, MPB3032AT, MPB3052AT, MPB3043AT manual Initialize Device Parameters, Identify Device XEC

Contents

C141-E045-02EN Revision Record Page Chapter Preface Conventions for Alert Messages Liability Exception Page Contents Interface Theory of Device OperationPage Operations Figures Page Tables Page Device Overview Features Functions and performance Interface AdaptabilityPage Specifications Device Specifications Specifications summary Model names and product numbers Model and product number Current and power dissipation Current fluctuation Typ. when power is turned on Acoustic noise specification Shock and vibration specification Error Rate Disk drive outerview Device Configuration System ConfigurationPage MPB3043AT Model Configuration of disk media heads 2 1 drive connection System Configuration ATA interface 3 2 drives connection 2 drives configurationPage Dimensions Mounting Cable Connections Jumper Settings Installation Conditions Dimensions Orientation PCA Limitation of side-mountingPage Service area ATA Cable Connections Device connector Specters Strip Cable connector specificationsAMP Device connection Power supply connector CN1 +12V Return +5V ReturnCN1 11 Factory default setting Jumper configuration Factory default setting 14 Example 1 of Cable Select 13 Jumper setting of Cable Select 092 Disk Outline Head MPB 3052AT M odelMPB3064AT Model Spindle ActuatorAir filter Circuit Configuration MPB30xxAT Block diagram Power-on Sequence Power-on operation sequence Self-calibration contents Command processing during self-calibration Self-calibration execution timechart Read/write preamplifier PreAMP Write circuitWrite precompensation algorithm Read/write circuit block diagram Read circuit Frequency characteristic of programmable filter PR4 signal transfer Time base generator circuit Write clock frequency and transfer rate of each zone Servo control circuit Physical sector servo configuration on disk surface Page Data-surface servo format Servo frame formatPAD Actuator motor control Spindle motor control Page Interface Shows the interface signals Host Physical Interface Interface signals Signal assignment on the interface connector Signal assignment on the connectorReset Dasp Hdmardy DiorHstrobe Pidag Ddmardy Iordy 1 I/O registers DA2 DA1 DA0 I/O registers Icrc UNC Idnf Abrt TK0NF Amnf Command block registersPage DEV HS3 HS2 HS1 HS0 BSY Drdy DSC DRQ ERR Page Srst Control block registers Command code and parameters 1 Command code and parameters Standby Immediate Sleep Check Power Mode Smart Flush Cache Command code and parameters 2 Command descriptions LBALBA LSB LBA LSB Read Multiple XC4 BSY Drdy Intrq DRQ Execution example of Read Multiple command LBA LSB LBA LBA Write Multiple XC5 LBA LSB Write Verify X3C LBA LSB 1F4 HCL Cylinder No. LSB / LBA 1F3 HSN Sector No Identify Device XEC Initialize Device ParametersPage Information to be read by Identify Device command 1 Information to be read by Identify Device command 2 Information to be read by Identify Device command 3 Identify Device DMA XEE SET Features XEF ‘AA’ Features register values and settable modes‘BB’ ‘CC’ SET Multiple Mode XC6 Page Diagnostic code Page 1F7 HCM 1F6 HDH Head No. /LBA MSB 1F5 HCH Cylinder No. MSB LBA Write Buffer XE8 Page Page Page Page XFF Page ’DA’ Features Register values subcommands and functionsPage 1FE 1FF Format of device attribute value data Format of insurance failure threshold value data Page Page Page 10 Command code and parameters Error posting Data transferring commands from device to host ∙ Execute Device Diagnostic ∙ Initialize Device Parameters Drdy DRQ Intrq BSYDRQ Intrq IOR BSY Drdy DRQ Intrq Write Sectors command protocol BSY Drdy Intrq Commands without data transfer DMA data transfer commands Other commands∙ Read Multiple ∙ Sleep ∙ Write Multiple ∙ Read DMA ∙ Write DMA IOW DRQ Dmarq Dmack Ultra DMA feature set Overview Phases of operation Data in transfer Pausing an Ultra DMA data in burst Terminating an Ultra DMA data in burst Page Page Data out transfer Pausing an Ultra DMA data out burst Terminating an Ultra DMA data out burst Page Ultra DMA CRC rules 11 Recommended series termination for Ultra DMA Series termination required for Ultra DMADIOR-HDMARDY-HSTROBE DIOW-STOP Timing PIO data transfer IOCS16 Iordy DIOR-/DIOW Dmarq Dmack DIOR-/DIOW Single word DMA data transfer Multiword data transfer 11 Multiword DMA data transfer timing mode 12 Initiating an Ultra DMA data in burst Ultra DMA data transfer Dmardy NAM Mode Comment MIN MAX 12 Ultra DMA data burst timing requirements 2 13 Sustained Ultra DMA data in burst Sustained Ultra DMA data in burst 14 Host pausing an Ultra DMA data in burst Host pausing an Ultra DMA data in burst 15 Device terminating an Ultra DMA data in burst Device terminating an Ultra DMA data in burst 16 Host terminating an Ultra DMA data in burst Host terminating an Ultra DMA data in burst 17 Initiating an Ultra DMA data out burst 18 Sustained Ultra DMA data out burst Sustained Ultra DMA data out burst 19 Device pausing an Ultra DMA data out burst Device pausing an Ultra DMA data out burst 20 Host terminating an Ultra DMA data out burst Host terminating an Ultra DMA data out burst 21 Device terminating an Ultra DMA data out burst Power-on and reset BSY DaspPdiag Dasp Operations Response to power-on Response to hardware reset Response to software reset Response to diagnostic command MPB Default parameters LS1 Logical addressLH0 LS1 LH1 LH2 LS2 LBA0 LBA1 LBA2 Power save modePage Power commands Alternating defective sectors Spare area Alternate cylinder assignment Data buffer configuration Caching operation ∙ Read Sector S ∙ Read Multiple ∙ Read DMAWrite DMA, Write Multiple Usage of read segment ∙ Write Sectors ∙ Write DMA ∙ Write Multiple DAP HAP Mis-hit data Empty data Read-ahead data HAP HAP set to hit position for data transfer Partially hit data Lack data Write Cache ∙ Write Sectors ∙ Write Multiple ∙ Write DMA Fujitsu Canada INC Fujitsu Limited