Device Specifications Specifications summary | Fujitsu MPB3043AT

1.2Device Specifications

1.2.1Specifications summary

Table 1.1 shows the specifications of the disk drive.

Table 1.1 Specifications

		MPB3021AT	MPB3032AT	MPB3043AT			MPB3052AT	MPB3064AT

Formatted Capacity (*1)		2162.76 MB	3243.66 MB	4325.52 MB			5249.66 MB	6488.29 MB

Number of Heads		2	3		4		5	6

Number of Cylinders				8,983 + 123
(User + Alternate & SA)				8,983 + 123
(User + Alternate & SA)

Bytes per Sector					512

Recording Method				8/9 PRML

Track Density				9531 TPI

Bit Density				161,815 BPI

Rotational Speed				5400 rpm ± 0.5%

Average Latency				5.56 ms

Positioning time
•	Minimum			2.5 ms typical
•	Average		(Read) 10 ms typical, (Write) 11 ms typical
•	Maximum		(Read) 19 ms typical, (Write) 20 ms typical

Start/Stop time
• Start (0 rpm to Drive Read)			Typical: 8 sec.,		Maximum:		16 sec.
• Stop (at Power Down)			Typical: 20 sec.,		Maximum: 26 sec.

Interface				ATA–3
			(Maximum Cable length: 0.46 m)

Data Transfer Rate
•	To/From Media			9.58 to 16.71 MB/s
•	To/From Host		16.7 MB/s Max. (burst PIO mode 4, burst DMA mode 2),
			33.3 MB/s Max. (burst ultra DMA mode 2)

Data buffer				256 KB

Physical Dimensions			25.4 mm × 101.6 mm × 146.0 mm
(Height × Width × Depth)				(1.0” × 4.0” × 5.75”)

Weight					500 g

*1: Capacity under the LBA mode and the CHS mode.

Under the CHS mode (normal BIOS specification), formatted capacity, number of cylinders, number of heads, and number of sectors are as follows.

Model	Formatted Capacity	No. of Cylinder	No. of Heads	No. of Sectors

MPB3021AT	2162.76	4,470	15	63

MPB3032AT	3243.66	6,704	15	63

MPB3043AT	4325.52	8,940	15	63

MPB3052AT	5249.66	10,850	15	63

MPB3064AT	6488.29	13,410	15	63

1 - 4

C141-E045-02EN

Image 19

Fujitsu MPB3043AT, MPB3054AT, MPB3032AT, MPB3052AT, MPB3021AT manual Device Specifications Specifications summary

Contents

C141-E045-02EN Revision Record Page Chapter Preface Conventions for Alert Messages Liability Exception Page Contents Interface Theory of Device OperationPage Operations Figures Page Tables Page Device Overview Features Functions and performance Interface AdaptabilityPage Specifications Device Specifications Specifications summary Model names and product numbers Model and product number Current and power dissipation Current fluctuation Typ. when power is turned on Acoustic noise specification Shock and vibration specification Error Rate Disk drive outerview Device Configuration System ConfigurationPage MPB3043AT Model Configuration of disk media heads 2 1 drive connection System Configuration ATA interface 3 2 drives connection 2 drives configurationPage Dimensions Mounting Cable Connections Jumper Settings Installation Conditions Dimensions Orientation PCA Limitation of side-mountingPage Service area ATA Cable Connections Device connector Device connection Cable connector specificationsSpecters Strip AMP +12V Return +5V Return Power supply connector CN1CN1 11 Factory default setting Jumper configuration Factory default setting 14 Example 1 of Cable Select 13 Jumper setting of Cable Select 092 Disk Outline MPB 3052AT M odel HeadMPB3064AT Model Actuator SpindleAir filter Circuit Configuration MPB30xxAT Block diagram Power-on Sequence Power-on operation sequence Self-calibration contents Command processing during self-calibration Self-calibration execution timechart Write circuit Read/write preamplifier PreAMPWrite precompensation algorithm Read/write circuit block diagram Read circuit Frequency characteristic of programmable filter PR4 signal transfer Time base generator circuit Write clock frequency and transfer rate of each zone Servo control circuit Physical sector servo configuration on disk surface Page Servo frame format Data-surface servo formatPAD Actuator motor control Spindle motor control Page Interface Shows the interface signals Host Physical Interface Interface signals Dasp Signal assignment on the connectorSignal assignment on the interface connector Reset Pidag DiorHdmardy Hstrobe Ddmardy Iordy 1 I/O registers DA2 DA1 DA0 I/O registers Icrc UNC Idnf Abrt TK0NF Amnf Command block registersPage DEV HS3 HS2 HS1 HS0 BSY Drdy DSC DRQ ERR Page Srst Control block registers Command code and parameters 1 Command code and parameters Standby Immediate Sleep Check Power Mode Smart Flush Cache Command code and parameters 2 LBA Command descriptionsLBA LSB LBA LSB Read Multiple XC4 BSY Drdy Intrq DRQ Execution example of Read Multiple command LBA LSB LBA LBA Write Multiple XC5 LBA LSB Write Verify X3C LBA LSB 1F4 HCL Cylinder No. LSB / LBA 1F3 HSN Sector No Identify Device XEC Initialize Device ParametersPage Information to be read by Identify Device command 1 Information to be read by Identify Device command 2 Information to be read by Identify Device command 3 Identify Device DMA XEE SET Features XEF ‘CC’ Features register values and settable modes‘AA’ ‘BB’ SET Multiple Mode XC6 Page Diagnostic code Page 1F7 HCM 1F6 HDH Head No. /LBA MSB 1F5 HCH Cylinder No. MSB LBA Write Buffer XE8 Page Page Page Page XFF Page ’DA’ Features Register values subcommands and functionsPage 1FE 1FF Format of device attribute value data Format of insurance failure threshold value data Page Page Page 10 Command code and parameters Error posting Data transferring commands from device to host ∙ Execute Device Diagnostic ∙ Initialize Device Parameters IOR BSYDrdy DRQ Intrq DRQ Intrq BSY Drdy DRQ Intrq Write Sectors command protocol BSY Drdy Intrq Commands without data transfer ∙ Read DMA ∙ Write DMA Other commandsDMA data transfer commands ∙ Read Multiple ∙ Sleep ∙ Write Multiple IOW DRQ Dmarq Dmack Ultra DMA feature set Overview Phases of operation Data in transfer Pausing an Ultra DMA data in burst Terminating an Ultra DMA data in burst Page Page Data out transfer Pausing an Ultra DMA data out burst Terminating an Ultra DMA data out burst Page Ultra DMA CRC rules DIOW-STOP Series termination required for Ultra DMA11 Recommended series termination for Ultra DMA DIOR-HDMARDY-HSTROBE Timing PIO data transfer IOCS16 Iordy DIOR-/DIOW Dmarq Dmack DIOR-/DIOW Single word DMA data transfer Multiword data transfer 11 Multiword DMA data transfer timing mode 12 Initiating an Ultra DMA data in burst Ultra DMA data transfer Dmardy NAM Mode Comment MIN MAX 12 Ultra DMA data burst timing requirements 2 13 Sustained Ultra DMA data in burst Sustained Ultra DMA data in burst 14 Host pausing an Ultra DMA data in burst Host pausing an Ultra DMA data in burst 15 Device terminating an Ultra DMA data in burst Device terminating an Ultra DMA data in burst 16 Host terminating an Ultra DMA data in burst Host terminating an Ultra DMA data in burst 17 Initiating an Ultra DMA data out burst 18 Sustained Ultra DMA data out burst Sustained Ultra DMA data out burst 19 Device pausing an Ultra DMA data out burst Device pausing an Ultra DMA data out burst 20 Host terminating an Ultra DMA data out burst Host terminating an Ultra DMA data out burst 21 Device terminating an Ultra DMA data out burst BSY Dasp Power-on and resetPdiag Dasp Operations Response to power-on Response to hardware reset Response to software reset Response to diagnostic command MPB Default parameters LS1 LH1 LH2 LS2 Logical addressLS1 LH0 LBA0 LBA1 LBA2 Power save modePage Power commands Alternating defective sectors Spare area Alternate cylinder assignment Data buffer configuration ∙ Read Sector S ∙ Read Multiple ∙ Read DMA Caching operationWrite DMA, Write Multiple Usage of read segment ∙ Write Sectors ∙ Write DMA ∙ Write Multiple DAP HAP Mis-hit data Empty data Read-ahead data HAP HAP set to hit position for data transfer Partially hit data Lack data Write Cache ∙ Write Sectors ∙ Write Multiple ∙ Write DMA Fujitsu Canada INC Fujitsu Limited