Detaching the control head | Furuno FR-2135S manual

4.Unfasten the M4 screw fixing the ground terminal of the connection cable.

5.Push the monitor forward until you hear a click.

6.Unscrew four screws fixing the top cover of the display unit.

7.Remove three clamps fixing the connection cable in the monitor unit.

8.Unfasten four screws fixing the right and left brackets on the control head.

9.Unfasten four screws fixing the right and left covers of the display unit.

10.Unfasten six screws fixing the right and left KB arms. 11. Unfasten three screws fixing the panel cover.

KB arm (L) 03-144-1341

M5X25 SUS 3 pcs.

Panel cover 03-144-1345

M4X10, 3 pcs.

Control head

KB arm (R) 03-144-1342

M5X25 SUS 3 pcs.

M5X25 SUS 4 pcs.

Figure 1-14 Detaching the control head

1-12

Image 20

Furuno FR-2135S manual Detaching the control head

Contents

Back 00080839301 Safety Instructions Use only the specified power cable Table of Contents Equipment Lists Standard Supply Optional Equipment Name Type Code No Qty Remarks System Configuration Scanner Unit Mounting considerations Installation precaution for S-band scanner unit Example How to lift scanner unit Attachment of lifting fixtures and collar Scanner unit assembling procedure Scanner unit assembling Installation of reinforcement ribs Fastening the scanner unit to the mounting platform Mounting of scanner unit Mounting procedure Display UnitBefore mounting the display unit Tabletop mounting Stay 10 Setting catch to hole in stay Console type mounting Separating the control head Display unit modification procedure Separate type control head kit Type OP03-151, No 14 Detaching the control head Control head modification procedure Connection of display unit to control head 16 How to attach KB fixing plate Attachment of hood Power Supply Unit This page is intentionally left blank Wiring Fabricating the power cable DPYCY-3.5 JIS cable Cable fed from back of display unit default method Leading in cables to the display unit Cable fed from outside display unit Cables fed from bottom of display unit console mount Connections Remove Connectors on the INT Board Connectors on the INT Board How to attach NH connector HOW to Attach NH Connector to Signal Cable 10 Scanner unit, port side view Fabricating signal cable S03-74 11 Fabricating the signal cable S03-74 13 Scanner unit, rear view 15 Fabrication of coaxial cable Changing AC Power Specification of Display Unit When the de-icer is installed 18 Power supply unit PSU-004 Tuning Initialization Accessing Menus for Initialization and AdjustmentAdjusting Video Signal Level Restoring default settings Heading Alignment Picture appears Deviated counterclockwise Adjusting Sweep Timing Suppressing Main Bang Antenna switch in tuning compartment Confirming Magnetron Heater Voltage Initial Setting Menus Scanner unit, stern side view Initial SETTING1 menu Press Radar Menu 0 0 0 Initial SETTING2 menu Initial SETTING3 menu Initial SETTING4 menu OWN Ship Information menu Installation and connection of the Gyro Converter Board Gyro Converter GC-8 INT Board Default setting Connection of external power supplyDIP switch, jumper wire settings Setting method 1 by gyrocompass specifications Gyrocompass type Setting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP5 Setting the heading readout on the radar display SW1 Installation of the ARP board ARP Board ARP-26 ARP board adjustment ARP Board 18P9002B Final check ARP Board ARP-26 RP Board RP-26 Table top/console type 10 Display pedestal Separate type control head Necessary parts RP-26-Z-2E Code no 13 Display pedestal, front view Performance Monitor PM-50 Necessary parts PM-50 and OP03-150 Code no Necessary parts OP03-156 Code no Alarm KitProcedure 16 Display unit, inside view Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page