112
LOAD DELAY | MOISTURE CONTROL SET POINT | LOAD DELAY | MOISTURE CONTROL SET POINT |
UNLOAD DELAY | PLENUM TEMPERATURE SET POINT | UNLOAD DELAY | PLENUM TEMPERATURE SET POINT |
Competitor
THIS DISPLAY INDICATES THE COMPUTER HAS STOPPED SENSING FLAME. THIS CAN BE CAUSED FROM RUNNING OUT OF FUEL, FLAME PROBE OUT OF ADJUSTMENT, OR THE BURNER FAILED TO IGNITE DURING IGNITION SEQUENCE.
|
| 000 |
|
| ||
|
|
|
| ERROR | ||
|
|
|
|
|
| FLAME OUT |
|
|
|
|
|
|
|
DRY TIME |
|
|
|
|
| OUT OF GRAIN TIME |
COOL TIME |
|
|
|
| UNLOAD TIME | |
|
|
|
| |||
| 000 |
| GRAIN | ||
|
|
| |||
|
|
| ERROR |
| OUT |
|
|
|
|
| |
|
|
|
|
|
|
DRY TIME |
|
|
|
| OUT OF GRAIN TIME |
COOL TIME |
|
|
|
| UNLOAD TIME |
|
|
|
| ||
THIS DISPLAY INDICATES THAT THE OUT OF GRAIN TIMER HAS EXPIRED. TRY INCREASI YOUR TIME ON THE OUT OF GRAIN TIMER.
Wiring
LOAD DELAY | MOISTURE CONTROL SET POINT | LOAD DELAY | MOISTURE CONTROL SET POINT |
UNLOAD DELAY | PLENUM TEMPERATURE SET POINT | UNLOAD DELAY | PLENUM TEMPERATURE SET POINT |
THIS DISPLAY INDICATES THAT THE GRAIN DISCHARGE SWITCH LOCATED IN THE REAR OF THE DRYER WAS ACTIVATED. THIS IS CAUSED BY THE GRAIN EXITING THE DRYER WAS NOT TAKEN AWAY FAST ENOUGH OR SOMEONE HAS OPENED THE DISCHARGE LID.
(SEE FIGURE 13)
DISCHARGE | 000 |
|
| |||
|
|
|
|
|
| |
|
|
|
| ERROR | ||
|
|
|
|
|
| |
DRY TIME |
|
|
|
|
| OUT OF GRAIN TIME |
COOL TIME |
|
|
|
| UNLOAD TIME | |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
000 |
| VAPOR | |||
|
|
| ERROR | TEMP | |
|
|
|
|
|
|
DRY TIME |
|
|
|
| OUT OF GRAIN TIME |
COOL TIME |
|
|
| UNLOAD TIME | |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
THIS DISPLAY INDICATES THAT THE VAPORIZER COIL NEEDS TO BE ADJUSTED SO THAT IT RUNS COLDER. (POSITION COIL AWAY FROM FLAME)
Series 100 Error
THIS DISPLAY INDICATES THAT A MOTOR OVERLOAD RELAY HAS TRIPPED. THIS RELAY MUST BE RESET MANUALLY. OPEN THE UPPER CONTROL BOX DOOR MAKE SURE THE POWER IS DISCONNECTED AND PUSH IN THE RED LEVERS ON ALL OF THE OVERLOAD RELAYS. NOTICE IF ONE OF THE LEVERS CLICKS
AS IT IS PUSHED IN. THEN INSPECT THE MOTOR THAT TRIPPED THE RELAY. DETERMINE IF THE MOTOR IS BEING OVERWORKED.
LOAD DELAY | MOISTURE CONTROL SET POINT | LOAD DELAY | MOISTURE CONTROL SET POINT |
UNLOAD DELAY | PLENUM TEMPERATURE SET POINT | UNLOAD DELAY | PLENUM TEMPERATURE SET POINT |
| 000 | 000 |
| THIS DISPLAY INDICATES THAT THE HOUSI |
| HOUSING | HIGH LIMIT SWITCH HAS TRIPPED. TO RESE | ||
MOTOR | THIS SWITCH, REMOVE 2 SCREWS TO THE | |||
ERROR | ERROR | TEMP | OF THE LRL BOX ON TOP OF THE FAN/BUR | |
OVERLOAD |
|
|
| |
|
|
|
| ASSEMBLY AND PUSH THE RED BUTTON IN |
DRY TIME | OUT OF GRAIN TIME | DRY TIME | OUT OF GRAIN TIME |
COOL TIME | UNLOAD TIME | COOL TIME | UNLOAD TIME |
LOAD DELAY | MOISTURE CONTROL SET POINT | LOAD DELAY | MOISTURE CONTROL SET POINT |
UNLOAD DELAY | PLENUM TEMPERATURE SET POINT | UNLOAD DELAY | PLENUM TEMPERATURE SET POINT |
Conditions
Reference
Portable Dryer
THIS DISPLAY INDICATES A LOSS OF AIR PRESSURE INSIDE THE DRYER. THIS IS USUALLY CAUSED BY LACK OF GRAIN INSIDE THE DRYER. THE AIRSWITCH MAY ALSO NEED TO BE ADJUSTED SO THAT IT BECOMES MORE SENSITIVE TO AIR PRESSURE.
(SEE FIGURE 1)
| NO AIRFLOW |
| 000 |
| ERROR |
DRY TIME | OUT OF GRAIN TIME |
COOL TIME | UNLOAD TIME |
000 | GRAIN |
PLENUM | |
ERROR | TEMP |
DRY TIME | OUT OF GRAIN TIME |
COOL TIME | UNLOAD TIME |
THIS DISPLAY INDICATES THAT THE PLENU ONE OF THE FIXED GRAIN HIGH LIMIT SWIT HAS TRIPPED. THESE SWITCHES RESET AU ICALLY WHEN COOLED DOWN. YOU MAY H START THE DRYER IN EMERGENCY COOLIN (SEE FIGURE 5 AND FIGURE 14)
Troubleshooting
