Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 600 Safety, CAUTION used with the safety alert symbol indicates a, injury, Injury

Models: 500 600

1 66

Download 66 pages 6.22 Kb

Page 10

1-5. SAFETY

	Model 500/600
1-5. SAFETY	The Henny Penny Pressure Fryer has may safety features
	incorporated. However, the only way to ensure a safe operation
	is to fully understand the proper installation, operation, and
	maintenance procedures. The instructions in this manual have
	been prepared to aid you in learning the proper procedures.
	Where information is of particular importance or safety related,
	the words DANGER, WARNING, CAUTION, and NOTICE are
	used. Their usage is described below.
	SAFETYALERT SYMBOL is used with DANGER,
	WARNING, or CAUTION which indicates a personal injury
	type hazard.
	NOTICE is used to highlight especially important information.
	CAUTION used without the safety alert symbol indicates
	a potentially hazardous situation which, if not avoided,
	may result in property damage.
	CAUTION used with the safety alert symbol indicates a
	potentially hazardous situation which, if not avoided,
	may result in minor or moderate injury.
	WARNING indicates a potentially hazardous situation
	which, if not avoided, could result in death or serious
	injury.
	DANGER INDICATES AN IMMINENTLY
	HAZARDOUS SITUATION WHICH, IF NOT
	AVOIDED, WILL RESULT IN DEATH OR SERIOUS
	INJURY.

1-2

1207

Image 10

Henny Penny 600, 500 Safety, CAUTION used with the safety alert symbol indicates a, may result in minor or moderate injury

Contents

OPERATOR’S MANUAL Henny Penny Pressure Fryers Model Model Computron 2000 ControlsPage Model 500/600 LIMITED WARRANTY FOR HENNY PENNY EQUIPMENTFM07-219-B Revised Page DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS Technical Data for CE Marked Products Section TABLE OF CONTENTSPage Section 5. TROUBLESHOOTING TABLE OF CONTENTS ContinuedSection 4. PROGRAMMING 1-1. PRESSURE FRYER P-H-T Pressure Heat Time 1-2. PROPER CARE SECTION 1. INTRODUCTION1-3. ASSISTANCE 1-4. MODEL VARIATIONS potentially hazardous situation which, if not avoided 1-5. SAFETYCAUTION used with the safety alert symbol indicates a may result in minor or moderate injurySECTION 2. INSTALLATION 2-2. UNPACKING INSTRUCTIONS Continued LOCATION position and install fryer to prevent tipping or move2-3. SELECTING THE FRYER ment. Restraining ties may be used for stabilizationVentilation must conform to local, state, and national codes 2-6. GAS SUPPLY 2-7. GAS PIPING Henny Penny Part No. 19921, which complies with Model 500/600 2-7. GAS PIPING Continued1207 The gas pressure regulator on the automatic gas valve 2-10. GAS PILOT & BURNER 7. Turn main power switch to ON position 2-13. ELECTRICAL REQUIREMENTS ELECTRIC FRYER REQUIREMENTS 2-14. ELECTRICALGAS FRYER 2-15. CHECKING THE FILTER PUMP Step 2-16. MOTOR BEARINGS 2-17. OPERATIONAL CHECKSPage SECTION 3. OPERATING INSTRUCTIONS Model 500/600 3-1. OPERATING CONTROLS ContinuedFigure 1 Control Panel 1207Description 3-2. OPERATING COMPONENTSItem Function3-2. OPERATING COMPONENTS A microswitch that provides protection for the frypot in the event an DO NOT OPEN THE DRAIN VALVE WHILE FRYPOTDescription 3-2. OPERATING COMPONENTSContinued FunctionModel 500/600 ELECTRIC MODEL Figure 2. Operating Controls3-2. OPERATING COMPONENTS Continued 1207Model 500/600 GAS MODEL Figure 3. Operating Controls3-2. OPERATING COMPONENTS Continued 1207Figure 5. Operating Controls Figure 4. Operating Controls 3-2. OPERATING COMPONENTS ContinuedModel 500/600 Figure 6. Operating Controls3-3. FILLING OR ADDING SHORTENING 3-4. CARE OF THE SHORTENING FOLLOW THE INSTRUCTIONS BELOW TO AVOID 1. Be sure the drain valve is in the closed position 3-5. BASIC OPERATIONS AND PROCEDURES Continued Step Step DO NOT ATTEMPT TO OPEN LID UNTIL THE WHEN FRYER IS UNDER PRESSURE. DO NOTLID WHEN THE FRYPOT IS PRESSURIZED ALLOWS PRESSURE DROPS TO ZERO. LID IS LOCKED3-7. FILTER PUMP MOTOR PROTECTOR- MANUAL RESET 3-6. REGULAR MAINTENANCE SCHEDULE ProcedureFrequency 3-8. FILTERING OF SHORTENING Step Step 3-8. FILTERING OF SHORTENING Continued 3-8. FILTERING OF SHORTENING Continued Step 7b Step 7c Step 7f When bubbling occurs, immediately close the filter valve. This prevents aeration of the shortening, therefore increasing shortening life 3-9. FILTER PUMP PROBLEM PREVENTION 6. Unthread the suction standpipe from the screen assembly 10. Fold the corners in and then double fold the open end 3-11. CLEANING THE FRYPOT 3-11. CLEANING THE FRYPOT Continued DEADWEIGHTASSEMBLY cleaned as follows 3-13. OPERATING INSTRUC TIONS FOR OPTIONAL DIRECT-CONNECT SHORTENING SYSTEMLID GASKET 3-14. REVERSING THEReversing the lid gasket helps to prevent early failure of lid gasket and the loss of pressure during a cook cycle3-15. LID LUBRICATION 3-16. LIMIT STOP ADJUSTMENT Step Step 3-16. LIMIT STOP ADJUSTMENT Continued 3-17. CLEANING THE SAFETY RELIEF VALVE3-18. CHECK & TIGHTEN ELEMENT SPREADER BARS Model 500 only 4-1. INTRODUCTION 4-2 TIME AND SET-POINT PROGRAMMING SECTION 4. PROGRAMMINGTo Change Set-Point Temperatures To change Product Cooking Times4-3. SPECIAL PROGRAM Inputs Status high limit, drain switch, fan switch, moduleMODE 4-3. SPECIAL PROGRAM MODE Continued Problem SECTION 5. TROUBLESHOOTING5-1. TROUBLESHOOTING GUIDE CauseDISPLAY ERROR CODESERROR CODE TABLE CAUSEDISPLAY 3-2. ERROR CODE TABLEContinued CAUSEgas fryers only GLOSSARYModel 500/600 gas fryers onlylevel also referred to as level indictor lines Model 500/600gas fryers only have three filter screens that include a crumb catchergas fryers only fryers, the lid assembly includes spindlesModel 500/600 gas fryers onlygas fryers only Model 500/600gas fryers only gas fryers onlyHenny Penny Corporation P.O.Box Eaton,OH Toll free in USA