Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 500, 600 Reversing The, Lid Gasket, and the loss of pressure during a cook cycle

Models: 500 600

1 66

Download 66 pages 6.22 Kb

Page 51

3-14. REVERSING THE

	Model 500/600
3-14. REVERSING THE	Reversing the lid gasket helps to prevent early failure of lid gasket
LID GASKET	and the loss of pressure during a cook cycle.

1.Back the 4 lid liner screws (2 on each side) out about 1/2 inch (12.7 mm).

2.Using a thin blade screwdriver pry out the gasket at the corners, and then pull gasket from lid.

Check the gasket for any tears or nicks. If the gasket is damaged, it needs to be replaced.

3.Clean the gasket and gasket seat with hot water and cleaning detergent. Rinse with clean hot water.

4.Install the gasket with the “good” side out and tighten the 4 screws.

Install the four corners of the lid gasket. Smooth the gasket into place, working from the corners towards the middle of each side.

1207

3-27

Image 51

Henny Penny 500, 600 Reversing The, Reversing the lid gasket helps to prevent early failure of lid gasket, Lid Gasket

Contents

Henny Penny Pressure Fryers Model Model Computron 2000 Controls OPERATOR’S MANUALPage LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT Model 500/600FM07-219-B Revised Page DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS Technical Data for CE Marked Products TABLE OF CONTENTS SectionPage TABLE OF CONTENTS Continued Section 5. TROUBLESHOOTINGSection 4. PROGRAMMING SECTION 1. INTRODUCTION 1-1. PRESSURE FRYER P-H-T Pressure Heat Time 1-2. PROPER CARE1-3. ASSISTANCE 1-4. MODEL VARIATIONS may result in minor or moderate injury 1-5. SAFETYCAUTION used with the safety alert symbol indicates a potentially hazardous situation which, if not avoidedSECTION 2. INSTALLATION 2-2. UNPACKING INSTRUCTIONS Continued ment. Restraining ties may be used for stabilization position and install fryer to prevent tipping or move2-3. SELECTING THE FRYER LOCATIONVentilation must conform to local, state, and national codes 2-6. GAS SUPPLY 2-7. GAS PIPING Henny Penny Part No. 19921, which complies with 2-7. GAS PIPING Continued Model 500/6001207 The gas pressure regulator on the automatic gas valve 2-10. GAS PILOT & BURNER 7. Turn main power switch to ON position 2-13. ELECTRICAL REQUIREMENTS ELECTRIC FRYER 2-14. ELECTRICAL REQUIREMENTSGAS FRYER 2-17. OPERATIONAL CHECKS 2-15. CHECKING THE FILTER PUMP Step 2-16. MOTOR BEARINGSPage SECTION 3. OPERATING INSTRUCTIONS 1207 3-1. OPERATING CONTROLS ContinuedFigure 1 Control Panel Model 500/600Function 3-2. OPERATING COMPONENTSItem Description3-2. OPERATING COMPONENTS DO NOT OPEN THE DRAIN VALVE WHILE FRYPOT A microswitch that provides protection for the frypot in the event anFunction 3-2. OPERATING COMPONENTSContinued Description1207 ELECTRIC MODEL Figure 2. Operating Controls3-2. OPERATING COMPONENTS Continued Model 500/6001207 GAS MODEL Figure 3. Operating Controls3-2. OPERATING COMPONENTS Continued Model 500/600Figure 6. Operating Controls 3-2. OPERATING COMPONENTS ContinuedModel 500/600 Figure 5. Operating Controls Figure 4. Operating Controls3-3. FILLING OR ADDING SHORTENING 3-4. CARE OF THE SHORTENING FOLLOW THE INSTRUCTIONS BELOW TO AVOID 1. Be sure the drain valve is in the closed position 3-5. BASIC OPERATIONS AND PROCEDURES Continued Step Step PRESSURE DROPS TO ZERO. LID IS LOCKED WHEN FRYER IS UNDER PRESSURE. DO NOTLID WHEN THE FRYPOT IS PRESSURIZED ALLOWS DO NOT ATTEMPT TO OPEN LID UNTIL THE3-6. REGULAR MAINTENANCE SCHEDULE Procedure 3-7. FILTER PUMP MOTOR PROTECTOR- MANUAL RESETFrequency 3-8. FILTERING OF SHORTENING Step Step 3-8. FILTERING OF SHORTENING Continued 3-8. FILTERING OF SHORTENING Continued Step 7b Step 7c Step 7f When bubbling occurs, immediately close the filter valve. This prevents aeration of the shortening, therefore increasing shortening life 3-9. FILTER PUMP PROBLEM PREVENTION 6. Unthread the suction standpipe from the screen assembly 10. Fold the corners in and then double fold the open end 3-11. CLEANING THE FRYPOT 3-11. CLEANING THE FRYPOT Continued DEADWEIGHTASSEMBLY cleaned as follows TIONS FOR OPTIONAL DIRECT-CONNECT SHORTENING SYSTEM 3-13. OPERATING INSTRUCand the loss of pressure during a cook cycle 3-14. REVERSING THEReversing the lid gasket helps to prevent early failure of lid gasket LID GASKET3-15. LID LUBRICATION 3-16. LIMIT STOP ADJUSTMENT Step Step 3-17. CLEANING THE SAFETY RELIEF VALVE 3-16. LIMIT STOP ADJUSTMENT Continued3-18. CHECK & TIGHTEN ELEMENT SPREADER BARS Model 500 only To change Product Cooking Times SECTION 4. PROGRAMMING4-1. INTRODUCTION 4-2 TIME AND SET-POINT PROGRAMMING To Change Set-Point TemperaturesInputs Status high limit, drain switch, fan switch, module 4-3. SPECIAL PROGRAMMODE 4-3. SPECIAL PROGRAM MODE Continued Cause SECTION 5. TROUBLESHOOTING5-1. TROUBLESHOOTING GUIDE ProblemCAUSE ERROR CODESERROR CODE TABLE DISPLAYCAUSE 3-2. ERROR CODE TABLEContinued DISPLAYgas fryers only GLOSSARYModel 500/600 gas fryers onlyhave three filter screens that include a crumb catcher Model 500/600gas fryers only level also referred to as level indictor linesgas fryers only fryers, the lid assembly includes spindlesModel 500/600 gas fryers onlygas fryers only Model 500/600gas fryers only gas fryers onlyToll free in USA Henny Penny Corporation P.O.Box Eaton,OH