Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 500, 600 warranty

Models: 500 600

1 66

Download 66 pages 6.22 Kb

Page 43

When bubbling occurs, immediately close the filter valve. This prevents aeration of the shortening, therefore increasing shortening life.

	Model 500/600
3-8. FILTERING OF	9. When the pump is pumping air only, the shortening in the frypot
SHORTENING	will appear to be boiling. Close the filter valve first and then
(Continued)	move the main power switch from PUMP to OFF. This will
	keep the filter pump and lines from filling up with shortening.

When bubbling occurs, immediately close the filter valve. This prevents aeration of the shortening, therefore increasing shortening life.

10.Check the level of the shortening if necessary, until it reaches the level indicator line on the rear wall of the frypot, or the top level indicator line on model 500s..

Step 9

11.After completing the filtering operation, empty and replace the condensation drain pan.

12.If frying is to be continued at this time, move the main power switch back to the COOK position, and allow time for reheating of the shortening.

Step 11

1207

3-19

Image 43

Henny Penny 500, 600 warranty

Contents

Henny Penny Pressure Fryers Model Model Computron 2000 Controls OPERATOR’S MANUALPage Model 500/600 LIMITED WARRANTY FOR HENNY PENNY EQUIPMENTFM07-219-B Revised Page DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS Technical Data for CE Marked Products Section TABLE OF CONTENTSPage Section 5. TROUBLESHOOTING TABLE OF CONTENTS ContinuedSection 4. PROGRAMMING 1-1. PRESSURE FRYER P-H-T Pressure Heat Time 1-2. PROPER CARE SECTION 1. INTRODUCTION1-3. ASSISTANCE 1-4. MODEL VARIATIONS may result in minor or moderate injury 1-5. SAFETYCAUTION used with the safety alert symbol indicates a potentially hazardous situation which, if not avoidedSECTION 2. INSTALLATION 2-2. UNPACKING INSTRUCTIONS Continued ment. Restraining ties may be used for stabilization position and install fryer to prevent tipping or move2-3. SELECTING THE FRYER LOCATIONVentilation must conform to local, state, and national codes 2-6. GAS SUPPLY 2-7. GAS PIPING Henny Penny Part No. 19921, which complies with Model 500/600 2-7. GAS PIPING Continued1207 The gas pressure regulator on the automatic gas valve 2-10. GAS PILOT & BURNER 7. Turn main power switch to ON position 2-13. ELECTRICAL REQUIREMENTS ELECTRIC FRYER REQUIREMENTS 2-14. ELECTRICALGAS FRYER 2-17. OPERATIONAL CHECKS 2-15. CHECKING THE FILTER PUMP Step 2-16. MOTOR BEARINGSPage SECTION 3. OPERATING INSTRUCTIONS 1207 3-1. OPERATING CONTROLS ContinuedFigure 1 Control Panel Model 500/600Function 3-2. OPERATING COMPONENTSItem Description3-2. OPERATING COMPONENTS DO NOT OPEN THE DRAIN VALVE WHILE FRYPOT A microswitch that provides protection for the frypot in the event anFunction 3-2. OPERATING COMPONENTSContinued Description1207 ELECTRIC MODEL Figure 2. Operating Controls3-2. OPERATING COMPONENTS Continued Model 500/6001207 GAS MODEL Figure 3. Operating Controls3-2. OPERATING COMPONENTS Continued Model 500/600Figure 6. Operating Controls 3-2. OPERATING COMPONENTS ContinuedModel 500/600 Figure 5. Operating Controls Figure 4. Operating Controls3-3. FILLING OR ADDING SHORTENING 3-4. CARE OF THE SHORTENING FOLLOW THE INSTRUCTIONS BELOW TO AVOID 1. Be sure the drain valve is in the closed position 3-5. BASIC OPERATIONS AND PROCEDURES Continued Step Step PRESSURE DROPS TO ZERO. LID IS LOCKED WHEN FRYER IS UNDER PRESSURE. DO NOTLID WHEN THE FRYPOT IS PRESSURIZED ALLOWS DO NOT ATTEMPT TO OPEN LID UNTIL THE3-7. FILTER PUMP MOTOR PROTECTOR- MANUAL RESET 3-6. REGULAR MAINTENANCE SCHEDULE ProcedureFrequency 3-8. FILTERING OF SHORTENING Step Step 3-8. FILTERING OF SHORTENING Continued 3-8. FILTERING OF SHORTENING Continued Step 7b Step 7c Step 7f When bubbling occurs, immediately close the filter valve. This prevents aeration of the shortening, therefore increasing shortening life 3-9. FILTER PUMP PROBLEM PREVENTION 6. Unthread the suction standpipe from the screen assembly 10. Fold the corners in and then double fold the open end 3-11. CLEANING THE FRYPOT 3-11. CLEANING THE FRYPOT Continued DEADWEIGHTASSEMBLY cleaned as follows TIONS FOR OPTIONAL DIRECT-CONNECT SHORTENING SYSTEM 3-13. OPERATING INSTRUCand the loss of pressure during a cook cycle 3-14. REVERSING THEReversing the lid gasket helps to prevent early failure of lid gasket LID GASKET3-15. LID LUBRICATION 3-16. LIMIT STOP ADJUSTMENT Step Step 3-17. CLEANING THE SAFETY RELIEF VALVE 3-16. LIMIT STOP ADJUSTMENT Continued3-18. CHECK & TIGHTEN ELEMENT SPREADER BARS Model 500 only To change Product Cooking Times SECTION 4. PROGRAMMINGTo Change Set-Point Temperatures 4-1. INTRODUCTION 4-2 TIME AND SET-POINT PROGRAMMING4-3. SPECIAL PROGRAM Inputs Status high limit, drain switch, fan switch, moduleMODE 4-3. SPECIAL PROGRAM MODE Continued Cause SECTION 5. TROUBLESHOOTING5-1. TROUBLESHOOTING GUIDE ProblemCAUSE ERROR CODESERROR CODE TABLE DISPLAYCAUSE 3-2. ERROR CODE TABLEContinued DISPLAYgas fryers only GLOSSARYModel 500/600 gas fryers onlyhave three filter screens that include a crumb catcher Model 500/600gas fryers only level also referred to as level indictor linesgas fryers only fryers, the lid assembly includes spindlesModel 500/600 gas fryers onlygas fryers only Model 500/600gas fryers only gas fryers onlyToll free in USA Henny Penny Corporation P.O.Box Eaton,OH