Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 600, 500 warranty TABLE OF CONTENTS Continued, Programming, Troubleshooting

Models: 500 600

1 66

Download 66 pages 6.22 Kb

Page 8

		Model 500/600
Section	TABLE OF CONTENTS (Continued)	Page
Section		Page
Section 4. PROGRAMMING		4-1
4-1.	Introduction	4-1
4-2.Time and Set-Point Programming		4-1
4-3.Special Program Mode		4-2
Section 5. TROUBLESHOOTING		5-1
5-1.	Troubleshooting Guide	5-1
5-2.	Error Codes	5-2
5-3.	Error Code Table	5-2
GLOSSARY		G-1
Distributors List - Domestic and International

ii

1207

Image 8

Henny Penny 600, 500 warranty TABLE OF CONTENTS Continued, Programming, Troubleshooting

Contents

OPERATOR’S MANUAL Henny Penny Pressure Fryers Model Model Computron 2000 ControlsPage FM07-219-B Revised LIMITED WARRANTY FOR HENNY PENNY EQUIPMENTModel 500/600 Page DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS Technical Data for CE Marked Products Page TABLE OF CONTENTSSection Section 4. PROGRAMMING TABLE OF CONTENTS ContinuedSection 5. TROUBLESHOOTING 1-3. ASSISTANCE 1-4. MODEL VARIATIONS SECTION 1. INTRODUCTION1-1. PRESSURE FRYER P-H-T Pressure Heat Time 1-2. PROPER CARE 1-5. SAFETY CAUTION used with the safety alert symbol indicates apotentially hazardous situation which, if not avoided may result in minor or moderate injurySECTION 2. INSTALLATION 2-2. UNPACKING INSTRUCTIONS Continued position and install fryer to prevent tipping or move 2-3. SELECTING THE FRYERLOCATION ment. Restraining ties may be used for stabilizationVentilation must conform to local, state, and national codes 2-6. GAS SUPPLY 2-7. GAS PIPING Henny Penny Part No. 19921, which complies with 1207 2-7. GAS PIPING ContinuedModel 500/600 The gas pressure regulator on the automatic gas valve 2-10. GAS PILOT & BURNER 7. Turn main power switch to ON position 2-13. ELECTRICAL REQUIREMENTS ELECTRIC FRYER GAS FRYER 2-14. ELECTRICALREQUIREMENTS 2-15. CHECKING THE FILTER PUMP Step 2-16. MOTOR BEARINGS 2-17. OPERATIONAL CHECKSPage SECTION 3. OPERATING INSTRUCTIONS 3-1. OPERATING CONTROLS Continued Figure 1 Control PanelModel 500/600 12073-2. OPERATING COMPONENTS ItemDescription Function3-2. OPERATING COMPONENTS A microswitch that provides protection for the frypot in the event an DO NOT OPEN THE DRAIN VALVE WHILE FRYPOT3-2. OPERATING COMPONENTS ContinuedDescription FunctionELECTRIC MODEL Figure 2. Operating Controls 3-2. OPERATING COMPONENTS ContinuedModel 500/600 1207GAS MODEL Figure 3. Operating Controls 3-2. OPERATING COMPONENTS ContinuedModel 500/600 12073-2. OPERATING COMPONENTS Continued Model 500/600Figure 5. Operating Controls Figure 4. Operating Controls Figure 6. Operating Controls3-3. FILLING OR ADDING SHORTENING 3-4. CARE OF THE SHORTENING FOLLOW THE INSTRUCTIONS BELOW TO AVOID 1. Be sure the drain valve is in the closed position 3-5. BASIC OPERATIONS AND PROCEDURES Continued Step Step WHEN FRYER IS UNDER PRESSURE. DO NOT LID WHEN THE FRYPOT IS PRESSURIZED ALLOWSDO NOT ATTEMPT TO OPEN LID UNTIL THE PRESSURE DROPS TO ZERO. LID IS LOCKEDFrequency 3-6. REGULAR MAINTENANCE SCHEDULE Procedure3-7. FILTER PUMP MOTOR PROTECTOR- MANUAL RESET 3-8. FILTERING OF SHORTENING Step Step 3-8. FILTERING OF SHORTENING Continued 3-8. FILTERING OF SHORTENING Continued Step 7b Step 7c Step 7f When bubbling occurs, immediately close the filter valve. This prevents aeration of the shortening, therefore increasing shortening life 3-9. FILTER PUMP PROBLEM PREVENTION 6. Unthread the suction standpipe from the screen assembly 10. Fold the corners in and then double fold the open end 3-11. CLEANING THE FRYPOT 3-11. CLEANING THE FRYPOT Continued DEADWEIGHTASSEMBLY cleaned as follows 3-13. OPERATING INSTRUC TIONS FOR OPTIONAL DIRECT-CONNECT SHORTENING SYSTEM3-14. REVERSING THE Reversing the lid gasket helps to prevent early failure of lid gasketLID GASKET and the loss of pressure during a cook cycle3-15. LID LUBRICATION 3-16. LIMIT STOP ADJUSTMENT Step Step 3-16. LIMIT STOP ADJUSTMENT Continued 3-17. CLEANING THE SAFETY RELIEF VALVE3-18. CHECK & TIGHTEN ELEMENT SPREADER BARS Model 500 only SECTION 4. PROGRAMMING To Change Set-Point Temperatures4-1. INTRODUCTION 4-2 TIME AND SET-POINT PROGRAMMING To change Product Cooking TimesMODE Inputs Status high limit, drain switch, fan switch, module4-3. SPECIAL PROGRAM 4-3. SPECIAL PROGRAM MODE Continued SECTION 5. TROUBLESHOOTING 5-1. TROUBLESHOOTING GUIDEProblem CauseERROR CODES ERROR CODE TABLEDISPLAY CAUSE3-2. ERROR CODE TABLE ContinuedDISPLAY CAUSEGLOSSARY Model 500/600gas fryers only gas fryers onlyModel 500/600 gas fryers onlylevel also referred to as level indictor lines have three filter screens that include a crumb catcherfryers, the lid assembly includes spindles Model 500/600gas fryers only gas fryers onlyModel 500/600 gas fryers onlygas fryers only gas fryers onlyHenny Penny Corporation P.O.Box Eaton,OH Toll free in USA