Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 500, 600 warranty The gas pressure regulator on the automatic gas valve

Models: 500 600

1 66

Download 66 pages 6.22 Kb

Page 19

The gas pressure regulator on the automatic gas valve

Model 500/600

2.8GAS LEAK TEST

Prior to turning the gas supply on, be sure the gas valve knob on the gas control valve is in the OFF position.

After the piping and fittings have been installed, check for gas leaks.A simple checking method is to turn on the gas and brush all connections with a soap solution. If bubbles occur, it indicates escaping gas. In this event, the piping connection must be redone.

To avoid fire or explosion, never use a lighted match or open flame to test for gas leaks. Ignited gas could result in severe personal injury and/or property damage.

2-9. GAS PRESSURE	The gas pressure regulator on the automatic gas valve
REGULATOR SETTING	is factory set as follows:
		Natural: 3.5 inches water column (0.87 kPa)
		Propane: 10.0 inches water column (2.49 kPa)
		The gas pressure regulator has been set by Henny Penny and
		is not to be adjusted by the user.
2-10. GAS PILOT & BURNER	Lighting Procedure - Solid State Ignition
LIGHTINGAND	1.	The frypot should be cleaned per the instructions in Section 3.
SHUTDOWN	2.	The frypot must be filled to the proper level with shortening.
PROCEDURE	2.
		Refer to Filling orAdding Shortening Section.
	3.	Turn main power switch to OFF position.
	4.	Turn the gas valve knob counterclockwise to the OFF position.
		(OFF pointed down)
	5.	Wait a sufficient length of time (at least 5 minutes) to allow any gas
		which may have accumulated in the burner compartment to escape
Step 4	6.	Turn the gas valve knob clockwise to the ON position.
		(ON pointed down)

1207

2-9

Image 19

Henny Penny 500, 600 warranty The gas pressure regulator on the automatic gas valve

Contents

Henny Penny Pressure Fryers Model Model Computron 2000 Controls OPERATOR’S MANUALPage Model 500/600 LIMITED WARRANTY FOR HENNY PENNY EQUIPMENTFM07-219-B Revised Page DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS Technical Data for CE Marked Products Section TABLE OF CONTENTSPage Section 5. TROUBLESHOOTING TABLE OF CONTENTS ContinuedSection 4. PROGRAMMING 1-1. PRESSURE FRYER P-H-T Pressure Heat Time 1-2. PROPER CARE SECTION 1. INTRODUCTION1-3. ASSISTANCE 1-4. MODEL VARIATIONS may result in minor or moderate injury 1-5. SAFETYCAUTION used with the safety alert symbol indicates a potentially hazardous situation which, if not avoidedSECTION 2. INSTALLATION 2-2. UNPACKING INSTRUCTIONS Continued ment. Restraining ties may be used for stabilization position and install fryer to prevent tipping or move2-3. SELECTING THE FRYER LOCATIONVentilation must conform to local, state, and national codes 2-6. GAS SUPPLY 2-7. GAS PIPING Henny Penny Part No. 19921, which complies with Model 500/600 2-7. GAS PIPING Continued1207 The gas pressure regulator on the automatic gas valve 2-10. GAS PILOT & BURNER 7. Turn main power switch to ON position 2-13. ELECTRICAL REQUIREMENTS ELECTRIC FRYER REQUIREMENTS 2-14. ELECTRICALGAS FRYER 2-17. OPERATIONAL CHECKS 2-15. CHECKING THE FILTER PUMP Step 2-16. MOTOR BEARINGSPage SECTION 3. OPERATING INSTRUCTIONS 1207 3-1. OPERATING CONTROLS ContinuedFigure 1 Control Panel Model 500/600Function 3-2. OPERATING COMPONENTSItem Description3-2. OPERATING COMPONENTS DO NOT OPEN THE DRAIN VALVE WHILE FRYPOT A microswitch that provides protection for the frypot in the event anFunction 3-2. OPERATING COMPONENTSContinued Description1207 ELECTRIC MODEL Figure 2. Operating Controls3-2. OPERATING COMPONENTS Continued Model 500/6001207 GAS MODEL Figure 3. Operating Controls3-2. OPERATING COMPONENTS Continued Model 500/600Figure 6. Operating Controls 3-2. OPERATING COMPONENTS ContinuedModel 500/600 Figure 5. Operating Controls Figure 4. Operating Controls3-3. FILLING OR ADDING SHORTENING 3-4. CARE OF THE SHORTENING FOLLOW THE INSTRUCTIONS BELOW TO AVOID 1. Be sure the drain valve is in the closed position 3-5. BASIC OPERATIONS AND PROCEDURES Continued Step Step PRESSURE DROPS TO ZERO. LID IS LOCKED WHEN FRYER IS UNDER PRESSURE. DO NOTLID WHEN THE FRYPOT IS PRESSURIZED ALLOWS DO NOT ATTEMPT TO OPEN LID UNTIL THE3-7. FILTER PUMP MOTOR PROTECTOR- MANUAL RESET 3-6. REGULAR MAINTENANCE SCHEDULE ProcedureFrequency 3-8. FILTERING OF SHORTENING Step Step 3-8. FILTERING OF SHORTENING Continued 3-8. FILTERING OF SHORTENING Continued Step 7b Step 7c Step 7f When bubbling occurs, immediately close the filter valve. This prevents aeration of the shortening, therefore increasing shortening life 3-9. FILTER PUMP PROBLEM PREVENTION 6. Unthread the suction standpipe from the screen assembly 10. Fold the corners in and then double fold the open end 3-11. CLEANING THE FRYPOT 3-11. CLEANING THE FRYPOT Continued DEADWEIGHTASSEMBLY cleaned as follows TIONS FOR OPTIONAL DIRECT-CONNECT SHORTENING SYSTEM 3-13. OPERATING INSTRUCand the loss of pressure during a cook cycle 3-14. REVERSING THEReversing the lid gasket helps to prevent early failure of lid gasket LID GASKET3-15. LID LUBRICATION 3-16. LIMIT STOP ADJUSTMENT Step Step 3-17. CLEANING THE SAFETY RELIEF VALVE 3-16. LIMIT STOP ADJUSTMENT Continued3-18. CHECK & TIGHTEN ELEMENT SPREADER BARS Model 500 only To change Product Cooking Times SECTION 4. PROGRAMMINGTo Change Set-Point Temperatures 4-1. INTRODUCTION 4-2 TIME AND SET-POINT PROGRAMMING4-3. SPECIAL PROGRAM Inputs Status high limit, drain switch, fan switch, moduleMODE 4-3. SPECIAL PROGRAM MODE Continued Cause SECTION 5. TROUBLESHOOTING5-1. TROUBLESHOOTING GUIDE ProblemCAUSE ERROR CODESERROR CODE TABLE DISPLAYCAUSE 3-2. ERROR CODE TABLEContinued DISPLAYgas fryers only GLOSSARYModel 500/600 gas fryers onlyhave three filter screens that include a crumb catcher Model 500/600gas fryers only level also referred to as level indictor linesgas fryers only fryers, the lid assembly includes spindlesModel 500/600 gas fryers onlygas fryers only Model 500/600gas fryers only gas fryers onlyToll free in USA Henny Penny Corporation P.O.Box Eaton,OH