Manuals / Henny Penny / Kitchen Appliance / Fryer

Henny Penny 500, 600 warranty Unthread the suction standpipe from the screen assembly

Models: 500 600

1 66

Download 66 pages 6.22 Kb

Page 45

6. Unthread the suction standpipe from the screen assembly.

Model 500/600

3-10. CHANGING THE FILTER ENVELOPE (Continued)

6. Unthread the suction standpipe from the screen assembly.

Step 6

7.Remove the sealer bar and discard the filter envelope.

8.Clean the top and bottom filter screen with soap and water.

Step 7

Rinse thoroughly with hot water.

Be sure that the filter screens, sealer bar, and the suction standpipe are thoroughly dry before assembly of filter envelope as water dissolves the filter paper.

9.Assemble the top filter screen to the bottom filter screen and slide the screens into a new filter envelope.

Step 9

1207

3-21

Image 45

Henny Penny 500, 600 warranty Unthread the suction standpipe from the screen assembly

Contents

Henny Penny Pressure Fryers Model Model Computron 2000 Controls OPERATOR’S MANUALPage LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT Model 500/600FM07-219-B Revised Page DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS Technical Data for CE Marked Products TABLE OF CONTENTS SectionPage TABLE OF CONTENTS Continued Section 5. TROUBLESHOOTINGSection 4. PROGRAMMING SECTION 1. INTRODUCTION 1-1. PRESSURE FRYER P-H-T Pressure Heat Time 1-2. PROPER CARE1-3. ASSISTANCE 1-4. MODEL VARIATIONS CAUTION used with the safety alert symbol indicates a 1-5. SAFETYpotentially hazardous situation which, if not avoided may result in minor or moderate injurySECTION 2. INSTALLATION 2-2. UNPACKING INSTRUCTIONS Continued 2-3. SELECTING THE FRYER position and install fryer to prevent tipping or moveLOCATION ment. Restraining ties may be used for stabilizationVentilation must conform to local, state, and national codes 2-6. GAS SUPPLY 2-7. GAS PIPING Henny Penny Part No. 19921, which complies with 2-7. GAS PIPING Continued Model 500/6001207 The gas pressure regulator on the automatic gas valve 2-10. GAS PILOT & BURNER 7. Turn main power switch to ON position 2-13. ELECTRICAL REQUIREMENTS ELECTRIC FRYER 2-14. ELECTRICAL REQUIREMENTSGAS FRYER 2-17. OPERATIONAL CHECKS 2-15. CHECKING THE FILTER PUMP Step 2-16. MOTOR BEARINGSPage SECTION 3. OPERATING INSTRUCTIONS Figure 1 Control Panel 3-1. OPERATING CONTROLS ContinuedModel 500/600 1207Item 3-2. OPERATING COMPONENTSDescription Function3-2. OPERATING COMPONENTS DO NOT OPEN THE DRAIN VALVE WHILE FRYPOT A microswitch that provides protection for the frypot in the event anContinued 3-2. OPERATING COMPONENTSDescription Function3-2. OPERATING COMPONENTS Continued ELECTRIC MODEL Figure 2. Operating ControlsModel 500/600 12073-2. OPERATING COMPONENTS Continued GAS MODEL Figure 3. Operating ControlsModel 500/600 1207Model 500/600 3-2. OPERATING COMPONENTS ContinuedFigure 5. Operating Controls Figure 4. Operating Controls Figure 6. Operating Controls3-3. FILLING OR ADDING SHORTENING 3-4. CARE OF THE SHORTENING FOLLOW THE INSTRUCTIONS BELOW TO AVOID 1. Be sure the drain valve is in the closed position 3-5. BASIC OPERATIONS AND PROCEDURES Continued Step Step LID WHEN THE FRYPOT IS PRESSURIZED ALLOWS WHEN FRYER IS UNDER PRESSURE. DO NOTDO NOT ATTEMPT TO OPEN LID UNTIL THE PRESSURE DROPS TO ZERO. LID IS LOCKED3-6. REGULAR MAINTENANCE SCHEDULE Procedure 3-7. FILTER PUMP MOTOR PROTECTOR- MANUAL RESETFrequency 3-8. FILTERING OF SHORTENING Step Step 3-8. FILTERING OF SHORTENING Continued 3-8. FILTERING OF SHORTENING Continued Step 7b Step 7c Step 7f When bubbling occurs, immediately close the filter valve. This prevents aeration of the shortening, therefore increasing shortening life 3-9. FILTER PUMP PROBLEM PREVENTION 6. Unthread the suction standpipe from the screen assembly 10. Fold the corners in and then double fold the open end 3-11. CLEANING THE FRYPOT 3-11. CLEANING THE FRYPOT Continued DEADWEIGHTASSEMBLY cleaned as follows TIONS FOR OPTIONAL DIRECT-CONNECT SHORTENING SYSTEM 3-13. OPERATING INSTRUCReversing the lid gasket helps to prevent early failure of lid gasket 3-14. REVERSING THELID GASKET and the loss of pressure during a cook cycle3-15. LID LUBRICATION 3-16. LIMIT STOP ADJUSTMENT Step Step 3-17. CLEANING THE SAFETY RELIEF VALVE 3-16. LIMIT STOP ADJUSTMENT Continued3-18. CHECK & TIGHTEN ELEMENT SPREADER BARS Model 500 only To Change Set-Point Temperatures SECTION 4. PROGRAMMING4-1. INTRODUCTION 4-2 TIME AND SET-POINT PROGRAMMING To change Product Cooking TimesInputs Status high limit, drain switch, fan switch, module 4-3. SPECIAL PROGRAMMODE 4-3. SPECIAL PROGRAM MODE Continued 5-1. TROUBLESHOOTING GUIDE SECTION 5. TROUBLESHOOTINGProblem CauseERROR CODE TABLE ERROR CODESDISPLAY CAUSEContinued 3-2. ERROR CODE TABLEDISPLAY CAUSEModel 500/600 GLOSSARYgas fryers only gas fryers onlygas fryers only Model 500/600level also referred to as level indictor lines have three filter screens that include a crumb catcherModel 500/600 fryers, the lid assembly includes spindlesgas fryers only gas fryers onlygas fryers only Model 500/600gas fryers only gas fryers onlyToll free in USA Henny Penny Corporation P.O.Box Eaton,OH