Basic printer operations | Homelite HL-1070, HL-P2500, HL-1660E, 2060

10/10/03

6.COMMANDS

6.1.Basic printer operations

The most common printer operations are described in this section. Some are invoked using control codes alone - the rest require escape sequences. For the sake of completeness, several instructions which are part of the Epson FX-850 mode instruction sets, but which an HL Series printer ignores are included.

Null

NUL (0) <00h>

NUL (ASCII code 0) is ignored.

Bell

BEL (7) <07h>

BEL (ASCII code 7) is ignored.

Space

SP (32) <20h>

The SP control code (ASCII code 32) moves the current print position one space to the right.

LPRINT CHR$(32); 'Print a space

Backspace

BS (08) <08h>

•The BS control code (ASCII code 8) moves the current print position one space to the left.

•This code is only effective when used with left justification, which is the default justification mode.

LPRINT CHR$(8); 'Backspace

Carriage return

CR (13) <0Dh>

•The CR control code (ASCII 13) moves the print position to the left margin on the current line.

•If automatic line feed is on, this code moves the current print position to the left margin on the next line. On some printers you can turn on automatic line feed using the control panel switches.

LPRINT CHR$(13); 'Carriage return

Line feed

LF (10) <0Ah>

•The LF control code (ASCII code 10) moves the current print position down one line, using the current line space setting.

•This code does not cause a carriage return to be performed.

•If the print position is such that this operation would move it below the bottom margin, the current page is ejected and the print position is moved to the top of the next page instead.

Form feed

FF

(12)

<0Ch>

•The FF control code (ASCII code 12) ejects the current page and moves the current print position to the top of the next page, unless the current page is blank.

•This code does not cause a carriage return to be performed, hence the print position does not change horizontally.

•If the current page is blank this control code has no effect.

LPRINT CHR$(12); 'Form feed

CHAPTER 6 EPSON - 9

Image 261

Homelite HL-1070, HL-P2500, HL-1660E, HL-2400CE, HL-1450, HL-1050, HL-1250, HL-1470N, 2060, HL-1270N manual Basic printer operations

Contents

Ver. B Revised for Addition of HL-2400Ce/3400CNRevised for Addition of HL-1650/1670N/3260N/2460 Ver. CPage Table of Contents HP-GL Graphics Language Control code Glossary Control panel reset Font Graphics mode initial settings LSB RAM ROM Tiff Page Chapter Introduction About the Manual About the Manual Areas of USE Using Word Processing Packages and SpreadsheetsGraphics Programming Font Development Introduction Chapter PCL Contents Using Fonts Using Graphics Macros Index Environments Job Control Command List Using graphics Status Readback Introduction Control Codes Controlling the Printer Esc&k#G 2738107#71 1Bh26h6Bh#47h Escape SequencesEsc&s0C 27381154867 1Bh26h73h30h43h Esc&s1C 27381154967 1Bh26h73h31h43h Display functions mode EscY 2789 1B59EscZ 2790 1B5A User default environment Factory default environmentEnvironments Modified print environment Size JOB ControlEsc&l#A 2738108#65 1Bh26h6Ch#41h Postcard Esc&l#G 2738108#71 1Bh26h6Ch#47h Output tray Esc&l#H 2738108#72 1Bh26h6Ch#48h Paper source Esc&l#U 2738108#85 1Bh26h6Ch#55h Left long-edge offset registration Esc&l#Z 2738108#90 1Bh26h6Ch#5Ah Esc&l#S 2738108#83 1Bh26h6Ch#53hEsc&a#G 273897#71 1Bh26h61h#47h EscE 2769 Esc&l1T 27381084984 1Bh26h6Ch31h54hEscCRFD EscCR!#R EscCRAB 27136566 1Bh0Dh41h42h EscCRGLEscCRAI 27136573 1Bh0Dh41h49h EscCRI 271373 1Bh0Dh49h Printable area PhysicalLogical Text area Portrait page dimensions 3300 2550 3180 150 Landscape page dimensions4200 2550 4080 150 3150 2175 3030 3507 2480 3389 2952 2078 2834 Esc&u#D 2738117#68 1Bh26h75h#44h Esc&a#L 273897#76Esc&a#M 273897#77 Setting the top margin Resetting the horizontal marginsEsc9 2739 1Bh39h Esc&l#E 2738108#69 1Bh26h6Ch#45h Setting the horizontal motion index HMI Setting the vertical motion index VMIEsc&l#C 2738108#67 1Bh26h6Ch#43h Sample file Esc&l#D 2738108#68 1Bh26h6Ch#44h Setting line spacingText length Esc&l#F 2738108#70 1Bh26h6Ch#46h Esc&l#P 2738108#80 1Bh26h6Ch#50h LengthPerforation skip Esc&l#L 2738108#76 1Bh26h6Ch#4Ch Esc&a#R 273897#82 Esc*p#Y 2742112#89 1Bh2Ah70h#79hEsc&a#V 273897#86 Esc&a#C 273897#67 Horizontal position Horizontal cursor positioning columnsHorizontal cursor positioning units Esc*p#X 2742112#88 1Bh2Ah70h#58h Using the cursor position stack Positioning the cursor using control codesHorizontal cursor positioning decipoints Esc&a#H 273897#72 Esc= 2761 1Bh3Dh Esc&l#O 2738108#79 1Bh26h6Ch#4FhEsc&a#P 273897#80 Lprint Brother Introduction Using Fonts BR-Script Fonts Microsoft Windows 3.1 TrueType Compatible FontsBrother Original Fonts Bound fonts Esc3@ Symbol collections Symbol setCriteria for font selection Type of character spacing Typeface Stroke weight Font Selection Commands Esc*c#R 274299#82Escf#Wdata 2749102#87 Character Requirements for MSL Symbol index Character Requirements for Unicode Symbol indexBit Value Designated Use Symbol set control command Symbol map Array of UISelecting the symbol set Escsymbol set ID 2740 Symbol Set Set primary font Symbol set Escsymbol set ID 2741Escs#C 2740115#67 1Bh28h73h#43h Escs#C 2741115#67 1Bh29h73h#43h Escs#P 2741115#80 1Bh29h73h#50h Escs#P 2740115#80 1Bh28h73h#50hEscs#H 2740115#72 1Bh28h73h#48h Escs#H 2741115#72 1Bh29h73h#48h Escs#V 2741115#86 1Bh29h73h#56h Escs#V 2740115#86 1Bh28h73h#56hEscCR!#H 271333#72 1Bh0Dh21h#48h EscCR!#V 271333#86 1Bh0Dh21h#56h Escs#B 2741115#66 1Bh29h73h#42h Escs#B 2740115#66 1Bh28h73h#42hEscs#T 2740115#84 1Bh28h73h#54h Escs#T 2741115#84 1Bh29h73h#54h Font Typeface Set primary Set secondary HL-1050/1250OCR-A OCR-B Esc&p#X character codes 2738112#88 1Bh26h70h#58h Transparent print dataEsc&d#D 2738100#68 Esc&d@ Esc&*c#D 27384299#68 Downloadable font manipulationEsc*c#F 27384299#70 Esc#X 2740#88 1Bh28h#58h Downloading Creating Downloadable FontsSending the font descriptor Escs#W font descriptor data 2740115#58 1Bh28h73h#88h Special Bitmap font Bitmap font Intellifont Scalable Bound font Intellifont Scalable Unbound font Byte 15 MSB LSB Upright Italic Alternate Italic Reserved Value PostureValue Width Value Structure Symbol set name Symbol set ID Symbol set name OCR a OCR B OCR M600 dpi Value Width type Value Stroke Weight Value Vendor Bit Field Designated Use MSL Symbol Index MSL Symbol Index Character Complement bits Unicode Symbol Index If font is compatible with 7-bit Ascii otherwise set to Unicode symbol index character complement bits Sending a character descriptor and data Sending a character code Bitmap continuation data Byte 0-1 Data Intellifont scalable font dataByte Data Intellifont-scalable contour data Continuation data for Intellifont scalable contour dataCompound character data of Intellifont scalable font TrueType character descriptor Byte Data TrueType scalable font PCL Landscape character Source, Pattern and Destination Using GraphicsFor example Set source transparency Esc*v#O 2742118#79 Set pattern transparency Esc*c#G 274299#71 Set area fill identity Esc*c#W data 274299#87 User-defined pattern commandFor 300 dpi Set pattern reference point Esc*c#Q 274299#81 User-defined pattern controlSet pattern type Esc*v#T 2742118#84 REM --- Background Pattern example Plotting Rectangles Next Gray REM --- Draw a Pattern Using 8 Gray Scales EscCRRO 1Bh0Dh52h4Fh Raster GraphicsEscCRRL 1Bh0Dh52h4Ch EscCRRM 1Bh0Dh52h4Dh Esc*r#S 2742114#83 1Bh2Ah72h#53h Esc*r#T 2742114#84 1Bh2Ah72h#54hEsc*b#Y 274298#89 Esc*b#M 274298#77 Tiff # = 5 indicates that adaptive compression is to be used Optional offset count byte = File Length APT OFFCcitt G3 & G4 Esc*b#Wdata 274298#87 1Bh2Ah62h#57h Esc*r#A 2742114#65 1Bh2Ah72h#41hEsc*b#Cimage data 274298#67 1Bh2Ah62h#43h Esc*rB 274211466 1Bh2Ah72h42h REM --- Transfer Raster Graphics Raster graphics example ESC*b##W Block 1 Block 2 Block Horizontal 1200-dpi image format mode Raster Graphic Mode Number of repeats Enter HP-GL/2 mode Vector GraphicsEsc%#B 2737#66 1Bh25h#42h Picture Frame Purpose of a Macro Macros Esc&f#Y 2738102#89 1Bh26h66h#59h Defining a MacroEsc&f0X 27381024888 1Bh26h66h30h58h Esc&f1X 27381024988 1Bh26h66h31h58h Esc&f2X 27381025088 1Bh26h66h32h58h Running a MacroEsc&f3X 27381025188 1Bh26h66h33h58h Esc&f4X 27381025288 1Bh26h66h34h58h Handling Macros AppleTalk configuration Execute dataEscCR!#E 271333#69 MIO video I/O port control Laser diode video interface port of the MIO port is closedLaser diode video interface port of the MIO port is opened Memory Status request Status ReadbackEntity Status Status Response Set status readback location type Status Response SyntaxESC*s#T 2742115#84 1Bh2Ah73h#54h Set status readback location unit ESC*s#I 2742115#73 1Bh2Ah73h#49h Inquire status readback entityEntity status response Font response Unbound scalable fonts Bound scalable fontsDownload fonts Location type 1 currently selected font Permanent download fonts Font extended response Symbol set response may be shown as follows Symbol set responseMacro response Use-defined pattern response Entity error codes Free space commandESC*s1M 27421154877 1Bh2Ah73h31h4Dh ESC*s#X 2742115#88 1Bh2Ah73h#58h ESC&r#F 2738114#70 1Bh26h72h#46h Index Pitch DimensionsRaster transfer Secondary font Transfer start Status response Memory 101Type of character spacing VMI Chapter PCL5C Color Palettes Introduction Command Using Simple Color Mode Set Simple ColorColor Modes ESC*r#U 2742114#85 1Bh2Ah72h#55h Using PCL Color Mode Set PCL Color Setting ESC*v#W 2742118#87 1Bh2Ah76h#57hShort Format ESC*b1V 10101010B ESC*r1AESC*b1V 11001100B ESC*b1V 11110000B ESC*b#V g, g, g, g, g... → Plane ESC*b#V r, r, r, r, r... → PlaneFfh 80h 40h 00h 00h 00h Bits/value #1, #2, #3 Long FormatWhite reference for value #1, #2, #3 Black reference for value #1, #2, #3 Using HP-GL/2 Color Mode Color Palettes ESC*p#P 2742112#80 1Bh2Ah70h#50h Push/Pop Palette Start Raster Transfer Color GraphicsSet Destination Raster Width Set Destination Raster Height Enter HP-GL/2 Mode Set Scale AlgorithmSend Raster Data by Plane Enhance Output Set Monochrome ModeSet Render Algorithm ESC*t#J 2742116#74 1Bh2Ah70h#4Ah User-defined Pattern Command Set Gamma CorrectionDownload Dither Matrix PC Pen Color Command Initialize Set Instruction CommandFunction Equivalent Condition Instruction Color White Black Red Green Yellow Blue Magenta Cyan NP Number of Pens Command CR Color Range CommandNP n Index Chapter HP-GL/2 Command Syntax Character Plot Instructions Command List 10/10/03 Introduction Terminology Fills Absolute and Relative Plotting Mnemonic Command SyntaxParameters Separators Units HP-GL Graphics WindowScaling Points P1 and P2 Scaling Preparing to Print Graphic Images Initialize Commands CommandsDF Default set instruction Function Equivalent Condition Returns the graphics mode to initial conditions Initialize set instructionHP-GL/2 origin IP Input scaling point Plot Area and Unit Setting InstructionsIP P1X, P1Y ,P2X, P2Y IR Input relative scaling points Min X coordinate of P1 SC ScaleMin Y coordinate of P1 Type type of scaling Sample Lprint INSP1 IW X1, Y1, X2, Y2 IW WindowRO Rotate coordinate system RO q PU Pen up Pen Control and Plot InstructionsPU X,Y PD Pen down PA X, Y PA Plot absolutePR Relative coordinate pen move PR X, Y AA Draw absolute arc Arc centre X coordinateQc Arc angle in degrees AR X, Y, qc, qd AR Draw relative arcAT Absolute arc three point AT X 1, Y 1, X 2, Y 2 , qd PE Polyline encoded RT Relative arc three point This CI Circle plotCI r, qd BR X1, Y1, X2, Y2, X3, Y3 . . . X1, Y1, X2, Y2, X3, Y3 BR Bezier relativeBZ Bezier absolute BZ X1, Y1, X2, Y2, X3, Y3 . . . X1, Y1, X2, Y2, X3, Y3 Polygon group PM Polygon modePM ms EA Edge rectangle absolute ER X, Y ER Edge rectangle relativeEP Edge polygon EW Edge wedge RA X, Y RA Fill rectangle absolute RR Fill rectangle relative RR X, YWG Fill wedge Specifies Non-zero winding fill method FP Fill polygon Plot Function Instructions AC Anchor cornerAC X, Y FT Fill type FT n, d, qFill type Option LA l, v , l , v , l LA Line attribute LT Line type selection LT , n , p ,m n Line pattern numberAny line residue are saved PW w, ,p w width PW Pen widthRF Raster fill definition RF i , w, h, p SM c SP n n pen numberSV s , option1, option2 s screen type TR n TR Transparency mode UL User-defined line type UL i ,gWU Select unit for pen width Character Plot Instructions SD Define standard font Introduction Number Valu Name Alternate italic Attribute = 6 Stroke weight Meaning Attribute = 2 Spacing Value9999 AD Define alternate font SS Select standard fontSA Select alternate font FI font-ID FI Select primary fontFN Select secondary font LB Character plot DT c , m c Character DT Define label terminatorLO Label origin LO p DI run, rise DI Absolute direction DR run, rise DR Relative direction DV path ,line DV Define variable text pathCP Relative character movement CP spaces ,lines CF fill , pen CF Character fill modeSI Set absolute character size SI width, height SR width, height SR Set relative character sizeSL Character slant SL tan φ TD mode SB nES width ,height Transparent Data Width LPT Lprint CHR$27 E Lprint CHR$27 %0B Absolute arc three point Relative coordinate pen move Relative direction Window 10/10/03 Chapter PJL HOW to USE PJL Device Attendance Commands About PJL PCL jobs Case of Using PJL with a Non-PJL PrinterPostscript jobs Other printer languages PJL Syntax and Format Format 3 @PJL command words CR LF@PJL Enter Language = emulation Crlf Format 1 ESC%-12345X Variables Invalid Commands Overview HOW to USE PJLPJL Job Requirement PJL Code PCL Job Postscript Job Command Group Command Description Command Group UEL Command Kernel CommandsExecute Command ESC%-12345X Enter Command Comment Command@PJL Comment remarks Crlf There are three methods of switching printer languages Printer Language SwitchingExplicit switching Implicit switching JOB Separation Commands JOB CommandName = job name @PJL EOJ Name = job name Crlf EOJ Command Print environment Environment Commands Remember these points about environments PJL reset conditions Initialize PJL environment variables General PJL Environment Variables Resolution OFF TimeoutsleepContextswitch Autosleep Powersave PasswordPowersavetime Mediatype RET Imageadapt Bidi LETTER, LEGAL, Executive INTRAY1SIZEDL, MONARCH, Ledger JISB4, LTRS, A4S Sourcetray INTRAY5SIZEAUTO, MPTRAY, TRAY1 AUTO, TRAY1, TRAY2 TRAY2SIZE A3, JISB4, LEDGER, A4, A4S JISB5, A4LONG, PostcardLETTER, LTRS, Executive EXECUTIVES, COM10, C5, DL Errorprint OFF, ON, Exceptcdcc Defpaper A4, LETTER, DefaultOemfont Compabitmap Traypriority MPT1T2T3T4, MPT4T3T2T1 T1T2T3T4 MP, T4T3T2T1MP FaxringdelayFfsuppress Lcddensity PCL-Specific Variables LETTER, A4, Legal PaperMONARCH, C5, DL, JISB5 LTRS, EXECUTIVES, B5S EPSON-Specific Variables IBM-Specific Variables LTRS, Executives B5S C1, C2, S HL-3260NOr Permanent Soft Fonts HPGL-Specific Variables PostScript-Specific Variables Frenchgerman ANSIASCII, CHRSET9825Scandinavian SPANISHLATIN, Jisascii ON, OFF LETTER, LEGAL, A4, ExectiveAUTO, PCL , POSTSCRIPT, IBM EPSON, Hpgl NORMAL, MIDDLE, High FirstprintENGLISH, FRENCH, German DUTCH, SPANISH, Italian PostScript-Specific Variable ISO85, WIN30, HPGERM, Hpspan Mctext Default Command Initialize Command@PJL Default Lparm personality variable = value Crlf Set Command Reset CommandExamples @PJL SET Lparm personality variable = value Crlf ESC%-12345X@PJL Crlf @PJL Reset Crlf ESC%-12345X Status Readback Commands Synchronization with the printerBasic format of status readback responses @PJL Inquire Lparm personality variable Crlf Inquire CommandResponse Syntax @PJL Inquire Lparm personality variable Crlf value Crlf Example This example requests the PCL-specific settings Dinquire Command@PJL Dinquire Lparm personality variable Crlf @PJL Dinquire Lparm personality variable Crlf value Crlf @PJL Echo words Crlf Echo Command Parameter Valid characters Info CommandAscii 33 to 255, SP, HT @PJL Info category Crlf ID category Information requesting Parameter Range of Characters Description Config categoryFont Cartridge Slots LCD Printer may send back the answer for the above Info command Printer sends back the answer for the above commandMemory category Printer may send back the answer for the above command Status categoryVariables category ORIENTATION=PORTRAIT 2 Enumeratedcrlf Portraitcrlf Ustatus category Device Ustatus CommandVerbose Timed @PJL Ustatus variable = value Crlf Device variableStatus code Example When the following wrong PJL command is sent Application sends the following commands to the printerJOB variables Timed variable Variable Ustatusoff Command JOB RecoveryThere are no parameters for this command Rdymsg Command Device Attendance Commands@PJL Rdymsg Display = message Crlf Display = message Stmsg Command Opmsg Command@PJL Opmsg Display = message Crlf @PJL Stmsg Display = message Crlf ONLINE, Reset KeyIf the operator press the Online key PCL-specific variables 26, 31 Demopage Chapter Epson FX-850 Command List Introduction Emulation Details NUL DC4 Introduction Ignored Commands ResolutionEmulation Details Conventions Syntax Escape sequence Control Panel Basic printer operations Escan 2797n EscSPn 2732n 1Bh20hnEsc$n1n2 2736n1n2 Esc\n1n2 2792n1n2 Esc 2762 Esc= 2761Esc# 2735 Escxn 27120n 1Bh78hn EscCR!#R 271333#82 1Bh0Dh21h#52h EscCRmode 2713modeEscEMn 2725n 1Bh19hn Esc9 2757 Set up Line Spacing Escjn 27106n 1Bh6Ahn Using TabsEscDn1n2n3...NUL 2768n1n2n3...00 1Bh44hn1n2n3...00h HT 09 09h Escbnm1m2m3...NUL 2798nm1m2m3...00 1Bh62hnm1m2m3...00h Using Standard CharactersEsc/ n 2747n VT 11 0Bh Escpn 27112n 1Bh70hn EscM 2777SI 15 0Fh EscSI 2715 EscWn 2787n EscH 2772SO 27 0Eh EscSO 2714 EscSn 2783n Esc5 2753EscT 2784 Escwn 27119n 1Bh77hn Esc6 2754 Esc!n 2733nEsc7 2755 EscIn 2773n Using customized characters EscRn 2782nEsctn 27116n 1Bh74hn Esc% nNUL 2737n00 Select standard / downloaded charactersCopy ROM character to RAM Esc000 Reassign image mode Select image modeEsc*mn1n2image data 2742mn1n2 Esc? cm 2763cm Escan1n2 2792an1n2 Print 9 bit image EscKn 1n 2image data 2775n1n2 Print single-density imagePrint double-density image EscLn 1n 2image data 2776n1n2 Print double-speed double-density image Print quadruple-density imageEscZn 1n 2image data 2790n1n2 Double-speed double-density image Epson Chapter IBM Proprinter Notation Used in this Emulation Description ESC EscZn1n2image data Set quadruple-density image mode Introduction Controlling the Printer Character Set selection Data Conventions Notation Used in this Emulation Description NUL 0 0h Basic Printer OperationBEL 07 07h ESC 27 1Bh Esc5n 2753n Automatic line feedEscQ22 27815050 EscQ3 278151 1Bh51h32h EscEMn 2725n 1Bh19hn EscCn 2767n FormatEscCNULn 27670n EscXmn 2788mn Esc1 2748 Set horizontal tabs Restore default tab settingsSet vertical tabs EscR 2782 Esc6 2756 Using CharactersEsc 2758 EscP n 2780n Can 24 18h SO 14 0Eh Esc-n 27126n 1Bh7Ehn Escn 2795n 1Bh5FhnEsc@n1n2n3n4n5n6 279164n1n2n3n4n5n6 1Bh5Bh40hn1n2n3n4n5n6 Select a character from the All Character Code table Escchar-code 2794Char-code 1Bh5EhChar-codeSelect character font Data EscKn 1n 2image data 2775n1n2image dataSample EscLn 1n 2image data 2776n1n2image data EscYn 1n 2image data 2789n1n2image data Set double-speed, double-density image mode EscZn 1n 2image data 2790n1n2image data Set quadruple-density image mode Feeder mode CancelOverline mode Length Perforation skip Pitch Print quality IBM Proprinter Chapter BAR Code Control Example Program Listings Introduction ESC i n ... n \ 27105n ... n Print BAR Codes or Expanded Characters Bar Code Mode Definition of ParametersBar Code Style = s0 or S0 Bar Code Scaling Width only Bar Code Human Readable Line On or OffQuiet Zone Expanded Character, Line Block Drawing & Box Drawing Width Bar Code & Expanded Character Offset in the Y-axisExpanded Character Rotation Isbn UPC-E Bar Code Data Start Check digitTotal 8 digits = 0 + 6 digits + 1 check digit Box Drawing Line Block DrawingExpanded Character Data Start Inter Leaved Example Program ListingsCodabar Label Print Chapter HP-GL Command List Introduction Command List Font Selection HP-GL SyntaxCoordinate System and Printing Area Coordinate system 3400CN/3260N/3450CN Letter Legal Printing area Initialization and Default Setting Instructions Xmin X coordinate of P1 SC Xmin, Xmax, Ymin, Ymax IW Input window IW X 1, Y 1, X 2, YPG Page feed X1, Y1 Xn, Yn X2,Y2 Current position 10 *** PAEX1 Qc = Arc Angle Qd = Chord Angle Radius Lprint LT2CI-40,5LT3CI50,5LT4CI- 60,5LT5CI70,5LT6CI80,5 Current position Radius in user units or graphics units EW r,q1,qc,qd Fill pattern specified by Current position WG r,q1,qc,qd LT , n , p FT n , d , q PW n PW-Pen widthTL Tick length TL l1,l2 PT d CS nCA n Ansi Ascii Character SetISO IRV SS Select standard character set Lprint DI,COSRADSINRADLBRETURN POINTCHR$13CHR$3 CP X,Y CP Character plot Lprint SI2,1.5LBLASERCHR$3 UC X1, Y1, X2, Y2..., Xn, Yn UC User-defined character EscCRRL Dual Context ExtensionsEscCRRM EscCRRD Fill wedge Scale Select alternate character set Select pen HP-GL Appendix a Comparison List IBM Proprinter XL 1850 12501450 1870N 5040 P2500 5050 5070N JIS B5 Postcard Feed Tray1From Lower Tray2 767 Appendix a -COMPARISON LIST-8 #0,1,2 Appendix a -COMPARISON LIST-10 1029 #0~6 1026 1028 #0~5 #0~4 150 200 #75,10200 300,60 #0,1,2 9,1 1027 1024 1028 Appendix a -COMPARISON LIST-14 Appendix a -COMPARISON LIST-15 1270N P2500 10702060 3400 1650 Appendix a -COMPARISON LIST-17 2600CN/3450CN Appendix a -COMPARISON LIST-19 5050/5070N/2600CN/3450CN DC2 Esc L n1 n2 Esc Y n1 n2 Esc Z n1 n2 ESC DC4 Can 5070N/2600CN/3450CN BAR Code 3450 P2500 1660e Appendix a -COMPARISON LIST-27 PCL, IBM Testprint Resifont Permfont PrtconfigPCL, PCLXL, Postscript PCL, PCLXL, POSTSCRIPT, IBM, Epson Epson Feature 3400CN/ 2600CN 1850/ 1870NReturned JOB, Timed @PJL Info FeaturesCrlf @PJL Info Drumlife Ltrs JISB5JISB4 ERJ Light PCLPostscr IPT, IBM Epson Stop A3, JISLong Cassett PESON, OFF OFF, on 500~500 Dutch ~99 ~240Spanish Finnish ~15 ~65535First Thin ThickTransp 3450CN 1270N/1450/1470NC1, S C1, C2, S 2, ...n 0x7FFFFFF ISOL2, ISOL5, ISOL6 ROMAN8, ISOL1WINL2, WINL5 WINL2, WONL5 WINL2, WINL5 PSTEXT, Vnintl 33, 0.5, 1.0, 1.5 10 ~155 columns 10 ~136 columns 1470N HL-1660e2400C/Ce 1650/1670N 3400CN/ 2600CN 1850/1870N Swedish SwedishmNorweg SAFRICA, PC8 ~145 columns ~126 columns HL-1050, HL-107033, 0.5, 1.0 Inch PC8, PC8DN, PC850 PC852, PC860 PC863, PC865 Appendix B FLASH/PCMCIA Card Commands Introduction HOW to Read the Card Commands Specification Introduction Commands HOW to Read the Card Commands SpecificationError Available Devices ESC CR ! 12340F ESC CR ! 12358F Slot NoESC CR ! 12341F ESC CR ! 12343F Physical format Command Format CommandHDD Error HL-1650/1670N/1850/1870N/5070N Logical format Command Save specified type Command Save Data CommandESC CR ! 12345F type4byte size4byte data Type = MCRO, Data Execute data Command Save data CommandData ESC CR ! 12347F ID2byte size4byte data Save secondary font Command Save primary font CommandDEVICE3 W Error HL-2460/3260N Font Delete all download fonts Command Delete download font with specified ID CommandHL-2400Ce/34000CN/7050/2600CN/3450CN Save download font with specified ID Command Delete macro with specified ID Command Delete all macros CommandDEVICE3 W Error HL-2460/3260N/2600CN/3450CN Macro DEVICE1 W Error DEVICE2 W Error DEVICE3 W Error Save macro with specified ID Command Available Device Description Slot 1 → Slot Slot 2 → Slot 1 is the default setting Slot 2 → SlotHL-2460 / 3260N Execute Macros USE Card Commands from PCLESC & l Call Macro ESC # X Designates soft font # as Primary Use Download Fonts USE Card Commands from Postscript Disk#%Internal HDD %disk2% Appendix C HBP Mode Commands Recommended Command String Descriptions Esc Space 1byte of dataESC%-12345X@PJLLF Printer enters the HBP mode when this command is received Command to Enter HBP Mode@PJLSpaceENTERSpaceLANGUAGESpace=SpaceHBPLF Function Command List HBP Commands Resolution setting commands Command @L + Function Commands Detailed ExplanationThis command sets the printer resolution Command Economy mode setting commands Command @E + Function Sleep mode setting commands Command This command sets the sleep time in minutes@T+ Mode setting commands Command @M+Recognized as undefined code Engine related execute commands Command Engine related setting commands Command@J+ @K+ Formfeed commands Command Graphic data input commands CommandExit commands Command Function @G+data length3bytes+data Graphic Data Format Appendix C HBP Mode Commands @PJL Default AUTOSLEEP=0LF Recommended Command String@PJL Default TIMEOUTSLEEP= 15LF Enter into HBP mode Appendix C HBP Mode Commands Appendix D Introduction General Specification Command Reference List Introduction Function Description General SpecificationHigh-capacity tray Sets of documents are printed and collated Commands Descriptions Command Reference ListPJL output tray & mode setting Format @PJL SET/DEFAULT OUTBIN=TrayName @PJL SET/DEFAULT MAILBOXPROTECT=TrayNumber PJL mailbox protection & bin number setting FormatPJL avoidance of mailbox bin full Command HL-2060/2460/7050 Lower unit PS output tray & mode setting Command PCL output tray setting CommandEsc&l#G 2738108#71 1Bh38h6ch#47h # setoutputmode BROutbinMode 0 setpagedevice Statusdict begin # setoutputprotect PS mailbox protection & bin number setting CommandBROutbinProtect # setpagedevice BROutbinProtect 4 setpagedevice 10/10/03 Appendix E Commands Descriptions Printed pages can be sorted or stapled PS output tray Command PCL output tray CommandSelect the Finisher/Stapler unit. Default = PJL output tray Format Default = Upper Left @PJL SET/DEFAULT STAPLE=StapleNamePS staple on/off Command PJL staple on/off Format PCL job separate Esc&l1T Command PS job offset on/off CommandPJL job offset on/off Format BRjoboffset truesetpagedevice