Homelite HL-1450, HL-P2500, HL-1660E, HL-2400CE, HL-1050, HL-1250 General PJL Environment Variables

10/10/03

6.2.Variables

6.2.1.Variables for HL-1050/1070/1250/1270N/1450/1470N/P2500/1650/1670N/3260N/2460/ 7050/1850/1870N/5040/5050/5070N

1.General PJL Environment Variables

The PJL environment variables which are not printer language-specific are listed in the following table. When using these variables, do not use LPARM.

Variables	Description	Sample Value Range
COPIES	Number of uncollated copies for each	1 to 200 (HL-1050/1070)
	page of the job.	1 to 99 (HL-1250/1270N/1450/
		1470N/P2500)
		1 to 999 (HL-1650/1670N/3260N/
		2460/7050/1850/1870N/5040/5050/
		5070N)
MANUALFEED	Feeds the paper from manual feed slot.	ON or OFF
ECONOMODE	Turn the economy mode (toner saving	ON or OFF
	mode) ON or OFF.

ECONOLEVEL	Selects the toner saving level from 1
	(high) to 3 (low).

1 to 3

0to 3 (HL-1650/1670N/3260N/ 2460/7050/1850/1870N/5040/ 5050/5070N)

PERSONALITY	Sets the emulation mode.	AUTO, PCL, IBM, EPSON,
		POSTSCRIPT (All models)
		HPGL (HL-3260N/2460/7050)
INPUTBUF	Sets the receiving buffer size value.	1 to 15 (HL-1650/1670N/2460/
		7050/1850/1870N/5040/5050/
		5070N)
XOFFSET	Sets the X offset ( horizontal offset )	-500 to 500 dots (HL-1050/1070/
	value.	1250/1270N/1450/1470N/P2500/
		1650/1670N/2460/7050/1850/
		1870N/5040/5050/5070N)
		-104 to 500 dots (HL-3260N)
YOFFSET	Sets the Y offset ( vertical offset ) value.	-500 to 500 dots
AUTOCONT	Auto Continue Mode	ON or OFF
TIMEOUTEMU	Sets the time-out value for automatic	1 to 99 seconds
	emulation switching.
PRIORITY	Sets the priority between EPSON or	EPSON or IBM
	IBM for automatic emulation switching.
HPFSEL		ALL, LJ4 (HL-1650/1670N/2460/
		7050/1850/1870N/5040/5050/
		5070N)
AUTOFF	Sets the auto FF setting to ON or OFF.	ON or OFF
TIMEOUTFF	Sets the timeout value for auto FF.	1 to 99 seconds
TIMEOUT	Sets the timeout value for Automatic	1 to 99 seconds
	interface switching

CDCCHIGH	Sets the high-speed transfer mode of the
	Centronics interface to ON or OFF.
DTRCTRL	Selects when DTR becomes low.
	0 = the printer is turned off-line by the
	SEL switch, the input buffer is full, or
	when a printer error occurs.
	1 = the printer is turned off-line by the
	SEL switch or when a printer error
	occurs.
	2 = the printer is turned off-line by the
	SEL switch.
	3 = the printer is never turned off-line.

ON or OFF (HL-1050/1070/1250/ 1270N/1450/1470N/P2500)

0to 2(HL-1050/1070/1250/ 1270N/1450/1470N/P2500)

0to 3(HL-1650/1670N/1850/ 1870N/5040/5050/5070N)

CHAPTER 5 PJL - 18