Honeywell 11255 manual Auto Rolls, Automatic Roll Filter Replacement

Auto Rolls

Automatic Roll Filter Replacement

Flanders automatic roll replacements are furnished wound on spools or cores, ready for installation without modifica- tion or adaptors. A core selection guide is printed on the back of this sheet. Six-foot-long kraft paper leaders and trailers are secured to the ends of every roll. Each roll con- tains 65 linear feet of filtering media in selected widths. Rolls are wrapped in heavy plastic and packed in cartons for shipment. The following media types are available:

Scrim-back spun glass

(Models AESx, BLCSxx, CBSx, FSx, CRSx, CSx, AMSx, TSxx, LRSx)

A nominal 2” thickness progressive density spun glass treated with dust-catching adhesive. The roll is backed on the downstream side with a scrim mesh. Density of the scrim is approximately 3 squares per square inch.

Skin-back spun glass

ModelsAEx, BLCx, CBx, Fxx, CRx, Cx, AMx, Tx, LRxx)

A nominal 2” thickness progressive density spun glass treated with dust-catching adhesive. The roll is backed on the downstream side with a spun glass “skin”.

Economy spun glass

(Models AEECx, BLECxx, CBECx, FECx, CRECx, CECxx, AMECx, TECx, LRECx)

A nominal 2” thickness spun glass with very light spun glass skin on the downstream side which is reinforced with a scrim mesh. Density of the sc im is approximately 1 square per square inch. Media weight is about two-thirds that of the standard scrim-back glass.

Polyester

(Models AEPx, BLCPxx, CBPx, FPx, CRPUx, CPUxx, AMPx, TPx, LRPxx)

A nominal 1/2” thickness dry, non-woven polyester syn- thetic fiber medium, re nforced on the downstream side with a scrim back ng. Scr m density is approximately 3 grids per square inch.

Treated Polyester

(Models AEPTx, BLCPTxx, CBTx, FPTx, CRPTx, CPTxx, AMPTx, TPTx, LRPTx, LAPTxx)

Same m dium as the polyester described above, but treat- ed with a dust-catching adhesive.

L - Designed	fit c	mmercial
“FulFlo” and	Mine	Safety

Appliance machines. Core con- sists of 3” ID fiberboard tube with drive pin 2-1/2” from one end.

F - Designed to fit Farr “Roll Kleen”. Core consists of 2-1/8” ID fiberboard tube. No drive pin, dis s or ups.

AM - Designed to fit Airmaze “Roll- A-M ze”. Core consists of 1-7/8” ID fiberboard tube with metal cup recessed 5/8” each end. A rectan- gular slot, 1-1/2 x 3/4”, is stamped in each cup.

T - Designed to fit Trane Company “Roll Filter”. Core consists of 2- 7/16” ID fiberboard tube with metal cup in each end, recessed 1-1/2” A 1-1/2” square is stamped in each cup.

CR - Designed to fit Carrier series 31NA and 31NC. Core is 27/167”

BLC - Designed to fit BLC Industries. Consists of a 1-1/2” metal pipe with 2 drive pins that are 1-3/8” from core end, and with 11” end plates.

AE - Designed to fit American Air Filter “Roll-O-Matic”. Core con- sists of 3/4” ID metal pipe with metal end plates approximately 11” diameter attached on each end.

CB - Designed to fit Cambridge “Autoroll”. Core consists of 3/4” metal pipe, no end plates unless specified on order.

C - Designed to fit Continental “Conomanual” or “Conomatic”. Core consists of 3” ID fiberboard tube with a drive pin 2-1/2” from one end.

30