Honeywell VISTA-20PSIA, VISTA-15PSIA setup guide 4204/4229 Relay Modules, Powerline Carrier Devices

Mounting and Wiring the Control

Connecting Relay Modules, Powerline Carrier Devices and Output Triggers

4204/4229 Relay Modules

1.Mount either remotely or in the control panel.

2.Connect each module to the control’s keypad terminals and set the device addresses as previously described in the Connecting Keypads and Other Addressable Device section. Use the connector harness supplied with the module. Use standard 4-conductor twisted cable for long wiring runs.

VISTA-20P: Up to 16 relays (if no powerline carrier devices are used)

VISTA-15P: Up to 8 relays (if no powerline carrier devices are used)

3.Connect the desired field wiring to the unit's relay contact terminals.

UL For UL installation requirements, refer to the Installation Instructions for the 4204.

4204		RELAY
	DIP SWITCH	4
	FOR SETTING DEVICE ADDRESS	TYPICAL
		(SHOWN "OFF")
	AND ENABLING/DISABLING TAMPER

COVER TAMPER (REED) SWITCH

4-PIN TOUCHPAD PLUG

EITHER OR BOTH

CAN BE USED

TB1

13 14 15 16

RELAY

3

RELAY

2

RELAY

1

1 2 3 4 5 6 7 8 9 10 11 12

C

NC

NO

C

NC

NO

C

NC

NO

C

NC

NO

Powerline Carrier Devices

UL Powerline Carrier devices and the 1361X10 Transformer are not UL Listed for fire or burglary functions and are intended for home automation.

YEL	DATA IN		TB2
BLK	FROM CONTROL
	(–) GROUND
GRN
	DATA OUT
RED	TO CONTROL
	(+) 12V	4204_conn-1-V0

Figure 13. 4204 Connections to Control

•Supervision: 4204 and 4229 modules are supervised against removal. The module’s device address is displayed as follows if a module is disconnected from the control’s terminals, or if the module cover is removed and the tamper jumper is installed:

Alpha: CHECK xx Wire Expansion FAULT xx Wire Expansion ALARM xx Wire Expansion

Fixed-Glass: lxx (or 91 if field *199 set for 2-digit display) where “xx is the module’s address.

•If communication/tamper failure occurs on a device with zones wired to it, all zones on the device will be displayed in their respective partitions.

1.Install the powerline carrier devices according to the instructions included with each. VISTA-20P: Up to 16 devices (if no relays are used)

VISTA-15P: Up to 8 devices (if no relays are used)

2.Use Programming Mode to enter the device house ID in data field*27, and enter the unit code using *79 Output Device menu Mode.

3.See connections diagram in the AC Wiring section for connecting the 1361X10 transformer to the triggers.

•You must use a 1361X10 Transformer instead of the 1321 Transformer.

•The 1361X10 Transformer provides AC power to the control panel, and also supplies signals from the control panel through the premises AC wiring to the Powerline Carrier devices (which are plugged into AC outlets). You can then make devices that are plugged into Powerline Carrier devices perform various functions in response to commands you enter at the security system keypads.

Canada: Use the PSC04 Powerline Interface as shown below.

8-PIN TRIGGER CONNECTOR
1	KEY	3	4	5	6	7	8
(RED)		(ORANGE)	(YELLOW)	(GREEN)	(BLUE)	(PURPLE)	(BLACK)
OUTPUT 17		+12 AUX.	GND (-)	OUTPUT 18	DATA	COM	SYNC
							SA4120XM-1 CABLE
							SYNC
							BLK
							GRN
							COM
							RED
							DATA
							YEL

X-10 PSC04

POWERLINE INTERFACE

1 2 3 4

MODULAR PHONE CORD (not supplied)

1 - BLACK

2 - RED

3 - GREEN

4 - YELLOW

Figure 14. PSC04 Powerline Interface Connections

2-11