Mounting and Wiring the Control
Keypad Notes
ARMED
READY
1 | OFF |
|
|
|
| |
4 |
|
| 2 | AWAY |
|
|
MAX |
| 3 |
| |||
| 5 |
| STAY | |||
7INST |
| TEST |
| |||
ANT | 8 | 6 |
| |||
|
|
| CODE |
| BYPASS | |
| READY | 0 |
| 9 | CHIME | |
|
|
|
|
| ||
|
|
|
|
| # |
|
Long Range Radio Connections
Set device addresses. Refer to the instructions included with the devices and set each address according to the Table of Devices Addresses.
See Keypad Programming Fields (fields
IMPORTANT: Each keypad must be assigned a unique, predefined address, from 16 to
23.The first keypad is address 16 (default = partition 1, all sounds enabled).
TOUCH SCREEN KEYPAD (AUI) NOTES:
•Use of up to 2 AUI devices (e.g., 6270, Symphony) is independent from standard keypads and does not affect the number of standard keypads the system can support.
•AUI devices must be set for either address 1 or address 2, depending on which unit is enabled in field *189.
•To ensure proper AUI device operation, connect only to controls having microprocessor version 3.0 or higher, and use AUI devices with the following rev levels: 6270 series use version 1.0.9 or higher; 8132/8142 (Symphony) series use version 1.1.175 or higher.
Connect the data in/data out terminals and voltage input terminals of the Long Range Radio to the control's keypad connection points.
Set the radio’s address to “03” following the instructions provided with the radio.
•Use compatible Long Range Radios (e.g., 7720PLUS, 7820, 7835C, or 7845C).
Wire Run Chart For Devices* Drawing Aux Power From The Control (12V+ &
Wire | TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED TO A SINGLE WIRE RUN | ||||
Size | 50 mA or less | 100 mA | 300 mA | 500 mA | 600 mA |
#22 | 900 ft (274m) | 450 ft (137m) | 150 ft (46m) | 90 ft (27m) | 75 ft (23m) |
#20 | 1400 ft (427m) | 700 ft (213m) | 240 ft (73m) | 140 ft (43m) | 120 ft (37m) |
#18 | 1500 ft (457m) | 1100 ft (335m) | 350 ft (107m) | 220 ft (67m) | 170 ft (52m) |
#16 | 1500 ft (457m) | 1500 ft (457m) | 550 ft (168m) | 350 ft (107m) | 270 ft (82m) |
*Includes Keypads, RF Receivers, Zone Expander/Relay Units, 4285/4286 Phone Module, and Long Range Radio.
Maximum wire lengths for any device that is homerun to the control can also be determined from the Wiring Run Chart, based on the current draw of that device alone.
The length of all wire runs for both partitions combined must not exceed 1500 feet (457m) when unshielded quad conductor cable is used (750 feet if shielded cable is used). This restriction is due to the capacitive effect on the data lines when quad cable is used.
Table of Device Addresses
This Device | Uses Address | Reports as†† | Enabled By… |
RF Receiver | 00 | 100 | *56 zone programming: input device type entry |
AUI 1 | 01 | 101 | automatic if AUI enable field *189 enabled for AUI 1 |
AUI 2 | 02 | 102 | automatic if AUI enable field *189 enabled for AUI 2 |
Long Range Radio | 03 | 103 | automatic if output to long range radio field *29 enabled |
4286 Voice Module | 04 | 104 | automatic if phone module access code field *28 enabled |
Zone Expanders (4219/4229): |
|
| *56 zone programming: input device type, entry 2, then: |
module 1 (for zones 09 - 16) | 07** | 107 | automatic if zone no. |
module 2 (for zones 17 - 24) | 08 | 108 | automatic if zone no. |
module 3 (for zones 25 - 32) | 09† | 109 | automatic if zone no. |
module 4 zones 33 - 40 | 10† | 110 | automatic if zone no. |
module 5 zones 41 - 48 | 11† | 111 | automatic if zone no. |
Relay Modules (4204): |
|
| *79 output device programming: device address prompt: |
module 1 | 12 | 112 | entered at device address prompt |
module 2 | 13 | 113 | entered at device address prompt |
module 3 | 14† | 114 | entered at device address prompt |
module 4 | † | 115 | entered at device address prompt |
| 15 |
|
|
Keypads: |
|
| data field programming as listed below: |
keypad 1 | 16 | n/a | always enabled for partition 1, all sounds enabled. |
keypad 2 | 17 | n/a | data field *190 |
keypad 3 | 18 | n/a | data field *191 |
keypad 4 | 19 | n/a | data field *192 |
keypad 5 | 20 | n/a | data field *193 |
keypad 6 | 21 | n/a | data field *194 |
keypad 7 | 22 | n/a | data field *195 |
keypad 8 | 23 | n/a | data field *196 |
5800TM Module | 28 | n/a | automatic |
** address 07 not available if
† 4219/4229 addresses
††Addressable devices are identified by “1” plus the device address when reporting. Enter a report code for zone 91 to enable addressable device reporting (default = reports enabled). See field *199 for addressable device (ECP)
