Honeywell VISTA-15PSIA Configurable Zone Type Charts, Zone Conditions Represented Entries

Installation and Setup Guide

Configurable Zone Type Charts

ENTRY 1				ENTRY 2
Response when system disarmed and zone is:						Auto
	Intact EOL		Open		Shorted	Restore	Vent Zone
RF zone normal			RF zone N/A	RF zn off-normal
0	= normal	0	= normal	0	= normal	0 = no	0 = no
1	= alarm	4	= alarm	1	= alarm	4 = yes	8 = yes
2	= trouble	8	= trouble	2	= trouble
3	= fault	12 = fault		3	= fault
		see note 5		see note 6
Entry 1 = EOL +		Open		Entry 2 = Short + auto restore + vent zone

ENTRY 3				ENTRY 4
Response when armed STAY and zone is:						Byp. when	Byp. when
	Intact EOL		Open		Shorted	disarmed	armed
RF zone normal			RF zone N/A	RF zn off-normal
0	= normal	0	= normal	0	= normal	0 = no	0 = no
1	= alarm	4	= alarm	1	= alarm	4 = yes	8 = yes
2	= trouble	8	= trouble	2	= trouble
3	= fault	12 = fault		3	= fault
		see note 5		see note 6
Entry 3 = EOL +		Open		Entry 4 = Short + byp. disarmed + byp. armed

ENTRY 5				ENTRY 6
Response when armed AWAY and zone is:						Dial Delay	Fault Delay
	Intact EOL		Open		Shorted	(see field *50)	(see field *87)
RF zone normal			RF zone N/A	RF zn off-normal
0	= normal	0	= normal	0	= normal	0 = no	0 = no
1	= alarm	4	= alarm	1	= alarm	4 = use delay	8 = use delay
2	= trouble	8	= trouble	2	= trouble
3	= fault	12 = fault		3	= fault		see note 1
		see note 5		see note 6
Entry 5 = EOL +		Open		Entry 6 = Short + dial delay + fault delay

ENTRY 7		ENTRY 8
Display Faults	Power Reset/	Use Entry	Use Exit	Respond as
	Verification	Delay 1/2	Delay	Interior Type
0 = show alarms	0 = no	0 = no	0 = no	0 = no
when armed	4 = power reset	1 = delay 1	4 = use exit	8 = yes
& disarmed	after fault	2 = delay 2	delay	see note 2
1 = don’t show	(with code +
alarms when	OFF)
armed (show	12 = verification
alarms, trbles,	(see zone
faults when	type 16)
disarmed)
3 = never show
any alarms,
trbles, faults
Entry 7 = fault display + power		Entry 8 = entry delay 1/entry delay 2 + exit delay +
reset/verification		interior zone type

ENTRY 9				ENTRY 10
Alarm Sounds		Use Bell	Respond as		Trouble	Chime when Chime
		Timeout	Fire Zone		Sounds	Mode On
0	= none	0 = no	0 = no	0	= none	0 = no
1	= steady	4 = yes	8 = yes	1	= periodic	4 = yes
	keypad				beep
2	= steady bell	see fields *32,	see zone type	2	= trouble
	and keypad	*33	09; see note 4		beeps
3	= pulsing bell
	and keypad
Entry 9 = alarm		sounds + bell timeout + fire zone		Entry 10 = trouble sounds + chime

INTACT	OPEN	SHORTED
EOL
		ZONE-003-V0

Zone Conditions Represented

in Entries 1-6

Configurable Zone Type Notes

1.Do not use the “fault delay” option with a configurable zone type if it is set for an entry or exit delay, otherwise unpredictable results may occur.

2.To create an interior type zone, select “respond as interior zone type” (entry 8, interior type = yes), and set zone response to “fault” in entries 3-4 to ensure fault displays; do not set as “normal,” “alarm,” or “trouble.”

3.Do not set fire zones to respond as

a“fault” (entries 1-6), otherwise

faults will not display unless the [∗] key is pressed.

4.4219/4229 modules must use EOLRs or unpredictable results may occur.

5.RF Zones: The “open” options in entries 1, 3, and 5 are not applicable for RF zones. Use the “intact EOL” option for normal RF zone conditions and “shorted” for off-normal RF zone conditions.

6.a. Zone-Doubling/Double- Balanced: A short on either zone of a zone-doubled pair or on a double-balanced zone causes a tamper condition.

b.For double-balanced zones, this entry must be “0”.

c.For zone-doubled zones, both zones of the doubled pair must be assigned the same response to a short.

4-10