Honeywell VISTA-15P, VISTA-20P Touch Screen Keypad AUI Enable, Keypad Programming Fields

Touch Screen Keypad (AUI) Enable

The system supports up to two touch screen style keypads (e.g., Symphony Advanced User Interface (AUI), and 6270 Touch Screen keypad. NOTE: Use of touch screen devices does not affect the number of standard keypads supported.

*189 AUI Device 1 and 2 Enable

VISTA-20P:Enter each touch screen (AUI) device’s home partition.

0 = disabled; 1 = partition 1; 2 = partition 2; 3 = common

VISTA-15P:0 = disabled; 1 = enabled

Set AUI 1 address to 1. Set AUI 2 address to 2.

AUI Compatibility Note: To ensure proper AUI device operation, connect only to controls having microprocessor version 3.0 or higher, and use AUI devices with the following rev levels: 6270 series use version 1.0.9 or higher; 8132/8142 (Symphony) series use version 1.1.175 or higher.

Keypad Programming Fields

To enable keypads:

1.Set desired address at keypad (refer to keypad’s instructions for setting the address).

2.Use data field program mode to enable keypad addresses, assign a partition, enable sound options in fields *190-*196 as shown in the table above.

3.If desired, use data field *198 to turn on the display of the partition number.

4.Set the following keypad-related data fields as required by the installation:

*21 Quick Arm Enable, *23 Forced Bypass, *84 Auto STAY Arm

5.If using touch screen devices (AUI), enable each unit in field *189 and set AUI 1 to address 1, AUI 2 to address 2.

NOTE: Each keypad must be assigned a unique address, starting at address 16 (address 16 is reserved for keypad 1, which is automatically set to partition 1 with all sounds enabled). Keypads programmed with the same address will give unpredictable results.

*190 Keypad 2 Device Address 17

Entry 1 – Partition Assignment: 0 = keypad disabled

1= partition 1 (VISTA-20P)/keypad enabled (VISTA-15P)

2= partition 2; 3 = common

Entry 2 – Sound Option:

0 = no suppression

1 = suppress arm/disarm and E/E/ beeps

2 = suppress chime beeps only

3 = suppress arm/disarm, E/E/ beeps and chime beeps

Entry 1: For VISTA-20P, enter the partition in which the keypad is located; for VISTA-15P, enter 1 to enable, or 0 to disable the keypad.

Entry 2: Enter the desired sound option for this keypad.

*191 Keypad 3 Device Address 18

See field *190 for entries and explanation.

*192 Keypad 4 Device Address 19

See field *190 for entries and explanation.

*193 Keypad 5 Device Address 20

See field *190 for entries and explanation.

*194 Keypad 6 Device Address 21

See field *190 for entries and explanation.

*195 Keypad 7 Device Address 22

See field *190 for entries and explanation.

*196 Keypad 8 Device Address 23

See field *190 for entries and explanation.

*197 Exit Time Display Interval

0 = no display; 1-5 = seconds between display updates

If enabled, keypads display the exit time remaining after arming the system, updated at the interval selected (i.e. if the exit delay is 30 seconds and “2” is selected in this field, the keypad display refreshes every 2 seconds, displaying 30, 28, 26, 24, etc.).

An interval greater than “1” may be necessary for some older keypads to allow users time to enter key presses between display updates.

FIXED-WORD KEYPAD NOTE: If using 2-digit display keypads (e.g. 6150RF), do not use exit times greater than the 96-second delay option. Using a longer delay time may cause end-user confusion because 2-digit display keypads cannot display times greater than “99.” If longer exit time is required by the installation, it is recommended that the Exit Time Display option be disabled (“0”).

*198 Display Partition Number

VISTA-20P. 0 = no; 1 = yes

If selected, the partition number is displayed in the upper-left corner of the display. This is useful when using the GOTO partition function.

*199 ECP Fail Display

0= 3-digit display (“1” + device address)

1= 2-digit fixed-display as “91”

Select “0” if using Alpha keypads and/or 3-digit Fixed- Word Display keypads. ECP faults will display “1” plus the device address (00-30) of device causing the fault (e.g., faults on device 07 display as “107”).

Select “1” if using 2-digit Fixed-Word Display keypads (e.g., certain 6128 series keypads). If selected, ECP faults for all devices will display as “91” on 2-digit displays, and “191” on 3-digit or Alpha keypads.

4-11