Honeywell VISTA-20PSIA Programming Installer and User Schedules, Schedule Number, Start Time

Menu Mode Programming

Programming Installer and User Schedules

The system provides schedules, which can be used to automatically control 11 types of system events at pre- defined times. Some events are reserved for the installer only.

VISTA-20P: Provides up to 32 schedules: 16 schedules for use by the end-user, 16 for use by the installer.

VISTA-15P: Provides up to 8 schedules: 4 schedules for use by the end user, 4 for use by the installer.

Start Scheduling mode by entering installer code + [#] + [6] [4] while in normal operating mode.

NOTE: The master code can only access schedules 01-16 (VISTA-15P = 01-04) and events 00-07.

E N T E R S C H E D N O .

0 0 = Q U I T 0 0

Schedule Number

VISTA-20P		VISTA-15P
01-16	= end-user schedules	01-04 = end-user schedules
17-32	= installer-only schedules	05-08- = installer-only schedules

[∗] to continue

Enter the desired schedule number.

	Enter Event
E N T E R E V E N T				= Forced Away Arming†
	00	= clear event	05
	01	= Relay On/Off	06	= Auto Disarm
	02	= User Access	07	= Display “Reminder”
	03	= Latch Key Report to Pager	10	= Display custom words ††
NOTE: Events 07 and
	04	= Forced Stay Arming†	11	= Periodic Test Report†††
10 cause the keypad to
	Press [∗] to continue
beep every 30 seconds
when messages are	Enter the desired event number for event you want to occur at a specified time.
displayed. Stop the	Events 10-11 are reserved for the installer only.
beeps by pressing any
	Latch key report (option 03) is sent to all pagers in the user’s partition and is active only
key.
	when the system is armed (message sent is 777-7777). User must be enabled for paging
	(see User Attributes in System Operation section).

†Forced bypass is automatically enabled regardless of setting in field *23.

††If selected, system displays custom words 8, 9, and 10 at defined time. Can be used as installer’s reminder message to the end user.

†††See key commands in Testing the System section to quickly set periodic test reporting intervals.

	Device Number (For event 01-relay on/off)
D E V I C E N U MB E R
	01-18 = device number; press [∗] to continue
X X
	Enter the physical device number as programmed in ∗79 Menu Mode, then press [*] to
	continue to the “Start” prompt.
	Device numbers 17 and 18 designate built-in triggers 1 and 2 respectively.
	Group Number (For event 02-user access)
G R O U P N U MB E R
	1-8 = group number; press [∗] to continue to the “Start” prompt
X
	Partition (For events 03-07, 10)
P A R T I T I O N
	0 = all partitions; 1 = partition 1; 2 = partition 2; 3 = common
X
	Press [*] to continue to the “Start” prompt.
	Start Time
S T A R T S MTW T F S
	01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM; Days = place “1” under days
H H M M A M 0 0 1 0 0 0 0
	Press [∗] to continue.
	Enter the event’s start time and days of the week to occur.
	To select days, position the cursor under the desired days using the [∗] key to move
	forward, then press “1” to select the day.

5-17