Tftp | HP Distributed Cloud Networking instruction

Table 7: HP VSC UDP/TCP Outbound/Remote Ports (Continued)

Port	UDP/TCP	Required/	Protocol Notes
		Optional


69	UDP	Optional	TFTP

123	UDP	Required	NTP

161/162	UDP	Optional	SNMP ‐ required for SNMP management

179	TCP	Required	BGP ‐ required for federated HP VSCs

514	UDP	Optional	Syslog

6633	TCP	Required	OpenFlow

Post-install Security Tasks

41

Image 41

HP Distributed Cloud Networking manual Tftp

Contents

HP Distributed Cloud Networking 3.0.R2 Installation Guide Warranty Table of Contents HP VRS and VRS-G Software Installation Documentation feedback Appendix Emulated Ethernet NIC Notes Audience About This Guide HP DCN Overview HP DCN Overview and Infrastructure HP Virtualized Services Directory HP DCN Infrastructure Requirements and Recommendations HP DCN Installation Overview Installation Setup HP VSD Installation Overview HP DCN Software InstallationInstallation Types HP VSD Hardware and Software Requirements Reinstalling HP VSD Installation Methods To change the root password, on each node, run HP VSD Installation Using QCow2 ImageSet Up Appliance VMs Verify the appliance VMs are running Connect to Appliance VMs Ping the gateway in this example, 192.168.100.1. ping Configure NetworkingConfigure DNS Server Verify the DNS reverse named file records as follows Set up forward DNS records as follows Install HP VSD using qcow2 Configure NTP Server Install VSD on Node HP VSD Installation Using ISO Disc ImageSet Up VM for ISO Extract and Mount ISO Image Configure Networking, DNS, and NTPInstall HP VSD Using ISO Xmpp Import Certificates on the Servers Ldap Store Example of Load Balancer ConfigurationIf you are using an Ldap store, see Using an Ldap Store HP VSC Software Installation Procedure on KVM HP VSC Software InstallationHP VSC Installation Notes For legacy two disk deployment use Copy HP VSC disks for libvirt accessFor single disk deployment use Emulated Disks Notes Emulated Ethernet NIC Notes HP VSC Software Installation Procedure on VMware Installing HP VSC on Esxi Using OVA HP VSC Software Installation Procedure on VMware HP VSC Software Installation HP VSC Software Installation Procedure on VMware HP VSC Update HP VSC configuration and reboot HP VSC Boot Options File Configuration HP VSC Basic Configuration Sistency file .ndx which will preserve system Dns‐domain dns‐name no dns‐domain To check connectivity To enable index persistence, the command is System-level HP VSC Configuration HP VSC System and Protocol Configuration NTP Servers and Time Zone In-band and Loopback IP Interfaces HP VSC Software Installation Post-install Security Tasks TCP Tftp Preparing the Hypervisor HP VRS and VRS-G Software InstallationVRS and VRS-G Installation Overview Install dependencies for Rhel Installing the VRS or VRS-G SoftwareVRS on Rhel This section contains If you have modified /etc/default/openvswitch, restart Install the VRS package for Rhel Install dependencies RebootInstall the following packages using dpkg VRS on Ubuntu 12.04 LTS with Ubuntu 12.04 Cloud Packages Restart the VRS service Installing the VRS Kernel Module for Mpls over GREVRS-G on Rhel or Ubuntu This section contains the following subsections Install dependencies for Dkms Installing VRS Kernel Module On RhelReboot to pick up correct kernel To verify which kernel is currently running Installing VRS Kernel Module On Ubuntu Configuring and Running VRS or VRS-GTo customize, use scripts that you run after bootup Verify that the VRS processes restart correctly VMware VRS VM Deployment Creating the dVSwitchIntroduction Prerequisites VSphere vSwitch Configurations Verifying the Creation of the dVSwitchVSwitch0 VSwitch1 Verifying Deployment Deployment of dVRSInformation Needed Additional Verification Deployment of dVRS Clean Install on XenServer VRS Installation on Citrix XenServer Install in the following order Remove stock openvswitchEnsue, with the following error Introduction Block Verification InstallationReboot XenServer Gives hpManagedNetworks Uuid = HPNetUUID Upgrade Existing dVRS Installation on XenServerEnsure that the xenmon to OVS socket is up Verify HPManagedNetwork is created Ensure that all packages are installed Root 15072 0.0 0.0 4032 772 hvc0 + 1545 Specifying the Active and Standby HP VSCs Running and Configuring VRSActive Contoller Standby Controller VRS Installation on Citrix XenServer Software technical support and software updates How to contact HPSupport and Other Resources Gather information before contacting an authorized support Related information Related information Support and Other Resources Documentation feedback Appendix Emulated Ethernet NIC Notes Modify the eth0 configuration Edit or create the br0 configuration