Message | Meaning | Action |
|
|
|
** (324) NSINIT: NRV | Internal consistency check failed | Rerun NSINIT. If the error |
Table Corrupt. Aborting | on the Nodal Routing Vector. | persists, reboot your system |
Startup. ** |
| and try again. If rebooting does |
|
| not solve the problem, this error |
|
| requires HP notification. |
|
|
|
** (325) Link: Error | An RTE error (errornum) | Refer to the appropriate RTE |
errornum accessing LU lu | occurred when NSINIT | reference manual for more |
(XLUEX). | attempted to determine the | information on the RTE error |
| status of a link (link LU lu). | code. Correct the link problem |
|
| and rerun NSINIT. |
|
|
|
** (350) NS Warning: No | The user requested DS/1000IV | This is an informational |
services, but then did not | message only. No action is | |
specified. ** | instruct NSINIT to initialize either | required. However, if |
| DS/1000IV to DS/1000IV or | DS/1000IV services are desired, |
| DS/1000IV to DS/3000 services. | rerun NSINIT. |
|
|
|
** (351) NSINIT: Invalid | An invalid monitor name was | The following monitor names are |
Monitor Name. ** | entered for DS/1000IV services. | valid for DS/1000IV services: |
|
| CNSLM, DLIST, EXECM, |
|
| EXECW, OPERM, PROGL, |
|
| PTOPM, RDBAM, RFAM, TRFAS, |
|
| and VCPMN. |
|
|
|
** (352) NSINIT: | The LU entered was previously | This is an informational |
Duplicate LU. Entry | entered as a BISYNC LU. | message only. No action is |
ignored. ** |
| required. |
|
|
|
** (353) NS: Error: | The DS/1000IV to DS/3000 | Rerun NSINIT with a correct LU. |
Wrong type or can’t read | driver type is invalid or NSINIT |
|
device type for LU: lu. | could not read the driver type |
|
** | from the specified LU (lu). |
|
|
|
|
** (354) NS: WARNING: No | DS/1000IV to DS/3000 services | This is an informational |
were requested, but no pool LUs | message only. No action is | |
links were specified. ** | or BISYNC LUs were specified. | required. However, if |
|
| DS/1000IV services are desired, |
|
| rerun NSINIT. |
|
|
|
** (355) NS: Error: | NSINIT could not initialize LU | This is an informational |
errornum initializing | lunum. errornum is an EXEC | message only. No action is |
Bisync LU lunum. ** | error code. | required. However, if you need |
|
| the LU, fix the card and rerun |
|
| NSINIT. |
|
|
|
** (356) NS: Invalid 802 | The least significant bit (LSB) of | If you are using NSINIT |
mcast addr. LSB of the | the first octet must be set for | interactively, enter a valid |
1st octet must be set. | multicast addresses. | address to subsequent prompts. |
|
| If not, correct your answer file |
|
| and try again. |
|
|
|
** (357) NS: Invalid | An invalid IEEE 802.3 address | If you are using NSINIT |
was entered. | interactively, enter a valid | |
is: |
| address to subsequent prompts. |
** |
| If not, correct your answer file |
|
| and try again. |
|
|
|
446 Program Specific Error Messages