Manuals / IBM / Computer Equipment / Personal Computer

IBM 2283, 6274 manual Safety notices, To connect, To disconnect

Models: 2283 6274

1 96

Download 96 pages 60.4 Kb

Page 7

Safety notices

DANGER

Electrical current from power, telephone, and communication cables is hazardous.

To avoid a shock hazard:

•Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.

•Connect all power cords to a properly wired and grounded electrical outlet.

•Connect to properly wired outlets any equipment that will be attached to this product.

•When possible, use one hand only to connect or disconnect signal cables.

•Never turn on any equipment when there is evidence of fire, water, or structural damage.

•Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

•Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

	To connect:		To disconnect:
	1.	Turn everything OFF.	1.	Turn everything OFF.
	2.	First, attach all cables to devices.	2.	First, remove power cords from outlet.
	3.	Attach signal cables to connectors.	3.	Remove signal cables from
	4.	Attach power cords to outlet.		connectors.
	4.	Attach power cords to outlet.	4.	Remove all cables from devices.
	5.	Turn device ON.	4.	Remove all cables from devices.
	5.	Turn device ON.

DANGER

Le courant électrique provenant de l’alimentation, du téléphone et des câbles de transmission peut présenter un danger.

Pour éviter tout risque de choc électrique :

•Ne manipulez aucun câble et n’effectuez aucune opération d’installation, d’entretien ou de reconfiguration de ce produit au cours d’un orage.

© Copyright IBM Corp. 2001

vii

Image 7

IBM 2283, 6274 manual Safety notices, To connect, To disconnect

Contents

User Guide Type Type First Edition August Copyright IBM Corp Contentsiv User Guide Notices and Trademarks vi User Guide To connect Safety noticesTo disconnect Do not Lithium battery noticeNe pas Modem safety informationLaser compliance statement Page xii User Guide Conventions used in this book About this bookxiii Quick Reference Access IBMHardware Maintenance Manual Related informationIdentifying your computer Chapter 1. Product overviewInternal drives Hardware featuresMicroprocessor MemorySecurity features System management featuresKeyboard and mouse features PowerAdditional software IBM preinstalled softwareAccess IBM SoftwareSelecting a location for your computer Chapter 2. Setting up your computerComfort Arranging your workspaceGlare and lighting Electrical outlets and cable lengths Air circulationUSB connectors Connecting cablesOther connectors Audio connectors10 User Guide Starting the computerChapter 3. Operating and caring for your computer Controls and status indicators12 User Guide Starting your computerShutting down the computer Using the Rapid Access keyboard2. Click Shut Down... or Turn off computer in Windows XP Rapid Access Wireless keyboard and mouse Customizing a Rapid Access ButtonChapter 3. Operating and caring for your computer Using the IBM ScrollPoint mouse Chapter 3. Operating and caring for your computer Accessing the optical driveHandling a disc Using an optical driveInserting and removing a disc Video device drivers Using video featuresUsing audio features Controlling volumeRecording and playing back sound Using power-management featuresSetting power schemes Using the Windows Start menuUsing the Standby button on the keyboard Using the power buttonLocking the cover Using security featuresLocking the keyboard Monitor and screen Cleaning your computer and keyboardTaking care of your computer Basics1. Shut down the operating system and turn off the computer Moving your computer Starting and using the IBM Setup Utility program Chapter 4. Using the IBM Setup Utility programViewing and changing settings Using passwords Exiting from the IBM Setup Utility programUser password 3. Select Security Profile by Device and press Enter Administrator passwordSetting, changing, and deleting a password Using Security Profile by DeviceThe startup sequence Other settings in the IBM Setup Utility programChanging the startup sequence 32 User Guide Handling static-sensitive devices Chapter 5. Installing optionsAvailable options Backing up configuration settingsTools required System board Component locationsChapter 5. Installing options Disconnecting cables Removing the rear cover Installing an adapter Removing the hard disk drive 40 User Guide Installing memory6. Replace the hard disk drive 7. Replace the rear cover Chapter 5. Installing optionsNotches 4. Pull out the release latches 4 then slide out the optical drive Removing the optical drive3. Disconnect the power cable and signal cable from the optical drive To remove the optical drive, do the followingChapter 6. Troubleshooting Is an error message displayed? Troubleshooting procedureIs the error message in this table? POST error codes Power-on self-test POST46 User Guide CodeDescription ActionDescription CodeAction Device troubleshooting charts Go to Problem typee. Click Volume Control Audio problemsSymptom Select AccessoriesSymptom Optical drive problemsAction 52 User Guide DVD disc problemsSymptom ActionSymptom Display/monitor problemsGeneral problems Symptom54 User Guide Intermittent problemsSymptom ActionSymptom Rapid Access IIIe Keyboard problemsAction 56 User Guide Rapid Access Wireless Keyboard problemsSymptom ActionSymptom ScrollPoint III Mouse problemsAction 58 User Guide ScrollPoint Wireless Mouse problemsSymptom ActionSymptom Memory problemsAction 60 User Guide Modem problemsSymptom ActionAction SymptomAction Symptom62 User Guide Symptom Optional-device problemsAction 64 User Guide Software problemsUniversal Serial Bus USB problems IBM Enhanced DiagnosticsThe IBM Enhanced Diagnostics are available on Creating an IBM Enhanced Diagnostics diskette3. Select Downloadable files To run diagnostics from the Product Recovery CD or program Running the IBM Enhanced Diagnostics programReplacing the battery To run diagnostics from the IBM Enhanced Diagnostics diskette1. Turn off the computer and all attached devices To change the battery, do the following3. Remove the old battery 4. Install the new battery Chapter 6. Troubleshooting5. Replace the cover, and plug in the power cord Getting information by fax Chapter 7. Getting information, help, and serviceUsing the World Wide Web Getting informationUsing the documentation and diagnostic programs Getting help and serviceCalling for service Installation and maintenance of network operating systems NOS Country Other servicesTelephone number Purchasing additional services 74 User Guide Armonk, NY U.S.A Notices and TrademarksNotices General notices IBM Director of Licensing IBM Corporation North Castle DriveTrademarks Processing date dataPage Page Index volumewireless keyboard 8, 14 mouse 8, 14 receiver 880 User Guide Part Number 23P1170 23P117023P1170 IBM@