Menu 1 Functions, Removing the Menu from the Screen | InFocus 570

Using the LitePro

•In Menu 2 and the Audio Menu, you can also use select/enter to select/de-select a function or to increase the value of a function.

Removing the Menu from the Screen

Press the menu button to remove the menu from the screen.

Resetting Menu Functions to the Default Settings

To reset all menu settings to their factory default values, select Reset from Menu 2. Refer to page 30 for more information about Reset.

Menu 1 Functions

Brightness

Adjusting the brightness changes the color saturation. Adjusting the brightness has no effect if a computer source is not connected.

To adjust the brightness:

1.Press the menu button to display Menu 1.

2.Use the right or left arrow buttons to highlight “Brightness”.

3.Press the up arrow button to increase brightness. Press the down arrow button to decrease brightness.

Tint

The tint function adjusts the red-green color balance. Adjusting the tint has no effect if a computer is not connected.

To change the tint:

1.Press the menu button to display Menu 1.

2.Use the right or left arrow buttons to highlight “Tint”.

3.Press the up arrow button to increase the amount of green in the image. Press the down arrow to increase the amount of red in the image.

26	LitePro 560/570 User’s Guide

Image 34

InFocus 570 Menu 1 Functions, Removing the Menu from the Screen, Resetting Menu Functions to the Default Settings, Tint

Contents

LCD Projector Users Guide Fold and tear here Page Page Certifications Declaration of Conformity Contents Power Cord Safety SummaryPower Source Do not look into the lens Lamp GroundingFuse Hot Surfaces Introduction Not shown Compatibility Cables and Adapters Usage Guidelines Remote Control Programmer KitIf You Need Assistance Setting Up the LitePro Image Size measured diagonally Connecting the LCD end of the LitePro cable Connecting an IBM-compatible desktop computer Connecting a Macintosh desktop computer Connecting an IBM-compatible laptop computer Connecting a Macintosh PowerBook Connecting a Composite Video Cable Connecting an S-Video Cable Connecting the Audio from a Video Player Connecting an external speaker Connecting a microphone Setting Up the LitePro Using the Remote Control Using the LiteProBasic Image Adjustment Turning the LitePro Off Focusing the Image Adjusting the Height Switching to the Spare Lamp Switching to the Spare Lamp Using the Remote Control Buttons Menu Select/enter Arrow buttonsNext Mute VolumePrev Mic Prog Standby Using the Menus Menu Highlighting Menu Functions Audio MenuMaking Changes to Menu Functions Removing the Menu from the Screen Resetting Menu Functions to the Default SettingsMenu 1 Functions Brightness Up/Down SyncLeft/Right Rear Projection Menu 2 FunctionsSource Prompt RS-232 Test PatternAuto Standby Reset Ntsc Source Enable Palette Prog Button Language Tracking Text Mode and Pixel Slice Video Type Comp Sharpness Volume and Audio Lock Audio Menu Functions Treble BassBalance and Fade Loudness Maintenance Cleaning the Lens Replacing the Projection Lamps Opening the Lamp Door Replacing Batteries in the Remote Control Bulb Guard Installing New Batteries Replacing the Fuse Locating the Fuse Removing the Fuse Holder Troubleshooting Before You Call for Assistance Problem Nothing on screen Solutions to Common ProblemsProblem Color or VGA text not being projected Problem Image is too wide or narrow for screen Problem Image is not centered on the screenProblem Only the test pattern is displayed Problem Image is out of focus Problem Image is noisy or streaked Problem Image and menus are reversed left to rightProblem LitePro displays vertical lines, bleeding or spots Problem Projected colors don’t match the monitor’s colors Specifications Appendix Appendix Accessories Cable Connector Pin Assignments LCD Connector Monitor and VGA Connectors GND Laptop Display Activation Chart AST FN-F1 Appendix Index Assistance, see Technical Support audio Lite show button 22 LitePro Quadra, see Macintosh Index Limited Warranty 010-0060-05 USA