Integra DTR-6.4/5.4 instruction manual Connecting your AV components, Connecting a DVD player DVD

Connecting your AV components

Connecting a DVD Player with 2-Channel (L/R) Audio Output

		ANTENNA		AM	FM 75
COMPONENT VIDEO
INPUT 2	INPUT 1	OUTPUT
Y		12 V					ZONE 2
		TRIGGER		IR OUT
		OUT	56K	40K	ZONE 2	DC IN	LINE OUT	RS232
					OUT	24V 1A
PB		A			A		L
					B
PR		B					R	REMOTE
			ZONE 2					CONTROL

	DIGITAL			VIDEO 3	VIDEO 2		VIDEO 1		DVD	MONITOR	IR
IN		OUT	COAXIAL	IN	OUT	IN	OUT	IN	IN	OUT	OUT
OPTICAL	1	OPTICAL									V
2
											IN
											S
			IN
			COAXIAL
IN	IN	OUT	IN	IN	OUT	IN	OUT	IN	FRONT	SURR	CENTER
GND										L
L
R										R
											SUB
PHONO	CD	TAPE		VIDEO 3	VIDEO 2		VIDEO 1
											WOOFER

DVD

Component video output

Video output

*

S video output

5. DVD player (DVD)

L (white)

Analog audio output

R (red)	Digital audio output
	(optical)

: Signal flow

*You do not have to make all the connection shown on the illustration above. For appropriate connection for your components, see “The flow of the video signals” on page 19.

5. Connecting a DVD player (DVD)

Connecting a DVD Player with 5.1-Channel Output

Using an RCA video cable, connect the video output jack (composite) of the DVD player to the DVD V IN jack of the DTR- 6.4/5.4. Or if the DVD player has an S video output jack, connect it to the DVD S IN jack with an S video cable. Or if the device has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the DTR-6.4/5.4.

With the initial settings of the DTR-6.4/5.4, the DVD input source is set for the COMPONENT VIDEO INPUT 1 jacks.

If you connect the DVD player to the COMPONENT VIDEO INPUT 2 jacks, this must be changed at “Input Setup” → “Component Video” (see page 34).

Using an RCA audio connection cable, connect the audio output jacks of the DVD player to the DVD FRONT L/R jacks of the DTR-

T	IN	FRONT SURR CENTER
		L
		R
VIDEO 1		SUB
		WOOFER

DVD

SUB

WOOFER

5. DVD player (DVD)

Analog audio output (center)

	Analog audio output
	(subwoofer)
L (white)	Analog audio output
R (red)	(surround L/R)
L (white)	Analog audio output
	(front L/R)

6.4/5.4. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has a 5.1-channel output, connect the DVD FRONT L/ R, SURR L/R, CENTER, and SUBWOOFER (5.1-channel input) jacks of the DTR-6.4/5.4 to the 5.1-channel output jacks of the DVD player (refer to right diagram for the connection examples). Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL IN COAXIAL jack or the DIGITAL IN OPTICAL jack of the DTR- 6.4/5.4 depending on the type of connector on the DVD player.

With the initial settings of the DTR-6.4/5.4, the DVD input source is set for digital input at the OPTICAL 1 jack (OPT 1). If the digital connection is made at a different jack, this must be changed at “Input Setup” → “Digital Input” (see page 34).

Note:

If the DVD player has both 5.1-channel audio outputs and 2- channel audio outputs, and you want to connect the DVD player only using the FRONT L/R jacks on the DTR-6.4/5.4, use the 2- channel audio output jacks on the DVD player.

R (red)

20