Integra DTR-6.4/5.4 Connecting your AV components, Connecting your audio components

Connecting your AV components

Here is an explanation of typical ways to connect various components to the DTR-6.4/5.4. There are many ways that any one component can be connected, and it is up to you to decide which method best fits your situation. The directions given here are only one option and should only be thought of as such. It is best to fully understand the nature of each connector and terminal as well as those of your components and their features to ascertain which method of connection is best.

Digital audio output (coaxial)

1. CD player (CD)

L (white)

Analog audio output

R (red)

2. Turntable (PHONO)

(DTR-6.4 only)

Ground wire

(earth) L (white)

Analog audio output

R (red)

		ANTENNA		AM
COMPONENT VIDEO
INPUT 2	INPUT 1	OUTPUT
Y		12 V
		TRIGGER		IR OUT
		OUT
			56K	40K
PB		A		A

						B
PR			B
				ZONE 2
IN	DIGITAL		COAXIAL	VIDEO 3	VIDEO 2
		OUT		IN	OUT	IN
OPTICAL	1	OPTICAL
2
			IN
			COAXIAL
IN	IN	OUT	IN	IN	OUT	IN

GND

L

R

PHONO CD TAPE VIDEO 3 VIDEO 2

3.Cassette tape deck, MD recorder, DAT deck, or CD recorder (TAPE)

Digital audio

input (optical)

L (white)

	Analog audio
R (red)	output
	L (white)
	Analog audio input
R (red)

: Signal flow

Connecting your audio components

Below is an example of how you can connect your audio components to the DTR-6.4/5.4. Refer to the diagram above for the following connection examples.

1. Connecting a compact disc player (CD)

Using an RCA audio cable, connect the output jacks of the compact disc player to the CD audio jacks of the DTR-6.4/5.4. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the compact disc player has a digital output, connect it to either the DIGITAL IN COAXIAL jack or the DIGITAL IN OPTICAL jack of the DTR-6.4/5.4 depending on the type of connector on the compact disc player.

With the initial settings of the DTR-6.4/5.4, the CD input source is set for digital input at the COAXIAL jack.

If the digital connection is made to a different jack, this must be changed at “Input Setup” → “Digital Input” (see page 34).

2. Connecting a turntable (PHONO) (DTR-6.4 only)

Using an RCA audio cable, connect the output jacks of the turntable to the PHONO audio jacks of the DTR-6.4. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

Note:

The DTR-6.4 is designed for use with moving magnet cartridges. For proper operation, connect a ground (or earth) wire to the GND terminal. For some turntables, however, connecting the ground wire may cause increased noise, and in such a case, a ground wire is not necessary and should not be connected.

3.Connecting a cassette tape deck, MD recorder, DAT deck, or CD recorder (TAPE)

Using RCA audio cables, connect the output jacks (PLAY) of the device to the TAPE IN audio jacks of the DTR-6.4/5.4 and connect the input jacks (REC) of the device to the TAPE OUT audio jacks of the DTR-6.4/5.4. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL IN COAXIAL jack or the DIGITAL IN OPTICAL jack of the DTR- 6.4/5.4 depending on the type of connector on the device.

With the initial settings of the DTR-6.4/5.4, nothing is allocated as the digital input source for TAPE (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page 34).

If the device has a digital input, connect it to the DIGITAL OUT jack of the DTR-6.4/5.4 for digital recording of the signal from the digital input of the DTR-6.4/5.4.

Note:

The output from the DIGITAL OUT jack of the DTR-6.4/5.4 is only the digital signal input to the DIGITAL IN jack.

18