Integra DTR-6.4/5.4 instruction manual Selecting a listening mode DTR-5.4, Listening Modes

Listening Modes

DTR-5.4

Listening mode buttons

	RC-517M
RCVR
Mode
CH			VOL
Disc
Audio Sel			Muting
A	Angle		Subtitle M
TV / VCR		Level
Random			Audio Adjust
	Rec
	Input Selector
DVD			CD
V 1	V 2	TAP	TUN
V 3	V 4	V 5	PH
	1	2	3
Pure A		Direct	Stereo
	4	5	6
SURR		THX	All ST
	7	8	9
SP A		SP B	CINE FLTR
+10		0	Search
Display		Dimmer	Zone 2
-- / ---			Enter

Listening mode buttons

CINE FLTR

Selecting a listening mode (DTR-5.4)

•Refer to pages 44 and 45 for more details of listening modes.

•Refer to page 45 for sources and listening modes.

•When playing Dolby Digital or DTS software, the listening mode will automatically change to Dolby Digital or DTS.

Tip:

You can set in advance a different listening mode for each input source. For more details, see page 57.

When using the remote controller, first press the RCVR Mode button before preceding to the step below.

Press one of the listening mode buttons to select the listening mode.

DTR-5.4

Remote controller

123

Pure A	Direct	Stereo
4	5	6
SURR	All ST	DSP
		9
		CINE FLTR

Direct: Changes the listening mode for the signal type that is currently being input from the selected input source to the Direct listening mode. If pressed, the corresponding settings in the “Input Setup” menu for the selected input source is also changed (see page 57).

Stereo: Changes the listening mode for the signal type that is currently being input from the selected input source to the Stereo listening mode. If pressed, the corresponding settings in the “Input Setup” menu for the selected input source is also changed (see page 57).

Surround (SURR): Changes the listening mode for the signal type that is currently being input from the selected input source to the surround mode that matches the signal type (e.g., Dolby Pro Logic II, Dolby Digital, DTS, or DTS Neo:6). If pressed, the corresponding settings in the “Input Setup” menu for the selected input source is also changed (see page 57).

All ST (remote controller only): Changes the listening mode for the signal type that is currently being input from the selected input source to the All Ch Stereo listening mode. If pressed, the corresponding settings in the “Input Setup” menu for the selected input source is also changed (see page 57).

DSP: Changes the listening mode for the signal type that is currently being input from the selected input source as shown below.

Orchestra → Unplugged → Studio-Mix → TV Logic → All Ch Stereo → Mono → T-D → Mono Movie → Enhance → Orchestra.

If pressed, the corresponding settings in the “Input Setup” menu for the selected input source is also changed (see page 57).

Original filter (CinemaFILTER) loading for movies (DTR-5.4 only)

The CinemaFILTER function gently decreases the level of the extreme high frequencies, compensating for overly-bright sounding motion picture soundtracks. Select this function if the sound from the front speakers is too bright.

This function only works in the Dolby Digital, Dolby Digital EX, Dolby Pro Logic II Movie, DTS, DTS-ES Discrete 6.1, DTS-ES Matrix 6.1, DTS Neo:6 Cinema, All Ch Stereo, Mono listening modes.

Press the CINE FLTR button on the remote controller.

The current setting is displayed. Press the button again to change the setting.

On: The CinemaFILTER function is used during playback.

Off: The CinemaFILTER function is not used during playback.

Note:

Dolby Pro Logic II Movie, DTS Neo:6 Cinema, Dolby Digital, and DTS are only enabled for multichannel playback.

47