Test x external | Intel SBCEFCSW guide

4.Choose one of the two types of port loopback tests to run:

•To run an internal loopback test, type the following command: test x internal

•To run an external loopback test, type the following command. A loopback plug must be installed for this test to pass.

test x external

✏NOTE

The external loopback test can be performed only on external switch module ports.

After the test type has been chosen and the command executed, a message on the screen will appear detailing the test results.

5.After the test is run, put the port back into online state by typing the following command (x = port number):

set port x state online

6.To verify the port is back online, type the following command. The contents of the AdminState field should be Online.

show port x

The online node-to-node test can test only one port at a time, and that port must be online and connected to an external device or a blade server Fibre Channel expansion card. To run the online node-to-node test, complete the following steps:

1.To start an admin session, type the following command: admin start

2.To run the online node-to-node test, type the following command: test x online

A series of test parameters are displayed on the screen.

3.Press the Enter key to accept each default parameter value, or type a new value for each parameter and press the Enter key. The TestLength parameter is the number of frames sent, the FrameSize (256 byte maximum in some cases) parameter is the number of bytes in each frame, and the DataPattern parameter is the pattern in the payload. Before running the test, make sure that the device attached to the port can handle the test parameters.

FCSM (admin) : user1> test x online

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the default value. If you wish to terminate this process before reaching the end of the list press 'q'

or 'Q' and the ENTER key to do so.

TestLength	(decimal value, 1-4294967295)	[100	]
FrameSize	(decimal value, 36-2148)	[256	]
DataPattern	(32-bit hex value or 'Default')	[Default]
StopOnError	(True/False)	[False	]

Do you want to start the test? (y/n) [n]

4.After all parameter values are defined, press the Y key to start the test.

60Intel Blade Server Switch Module SBCEFCSW Management and User’s Guide

Image 74

Intel SBCEFCSW manual test x external

Contents

Order Number C39671-003 Intel Blade Server Switch ModuleSBCEFCSW Management and User’s Guide Disclaimer Contents Page Contents 4 Switch management utility functions Safety and regulatory information General Safety Electrical Safety Handling electrostatic discharge-sensitivedevices Regulatory specifications and disclaimers Safety compliance Electromagnetic compatibility EMC Electromagnetic compatibility notice USA Japan EMC Compatibility RRL Korea xiii English translation of the previous noticePage 1 Introduction Related publications •QLogic SAN Configuration Guide: CLARiiON Storage QLogic SAN Solutions Guide•QLogic Switch Interoperability Guide •QLogic SAN Configuration Guide: LSI Storage Notices used in this book Page 2 Command line interface CLI Logging on to a switch command Command syntaxCommands Admin authority command Table 1. Commands listed by authority levelUser authority commands Admin session commands cancel Admin commandadmin Authority add alias members Alias commandalias copy alias_source alias_destination remove alias members rename alias old alias new activate config Config commandconfig backup FCSM admin : user1> config edit save configFCSM: user1> admin start FCSM admin-config :user1> config cancel MMDDhhmmCCYY Date commanddate Authority Authority Fallback commandfallback Syntax help Help commandcommand keyword FCSM: user1> help set beacon set beacon On | Off Authority History commandhistory Syntax image Image commandcleanup unpack file Authority Lip command for external ports onlyport number Syntax account_name Passwd commandpasswd Authority Syntax Ps commandAuthority Examples Authority Quit commandquit, exit, or logout Syntax config config name Reset commandreset switch Default Table 2. Switch configuration defaultsTable 3. Port configuration defaults External port 0,15 default External port 0,15 default Table 3. Port configuration defaults continuedTable 4. Threshold configuration defaults Internal port 1-14default Default Table 5. SNMP configuration defaultsTable 6. System configuration defaults Default config option Set commandalarm clear setup option Online switch stateDiagnostics Offline port port number Set Config commandset config ports port number Table 8. Set Config switch parameters switchTable 7. Set Config port parameters continued Parameter Table 9. Set Config threshold parameters thresholdTable 8. Set Config switch parameters continued zoning Default Table 10. Set Config zoning parametersOn or to RAM volatile Off. The default is On Examples FCSM user1 admin start LoginMonitoringEnabled archive Set Log commandset log clear Port SwitchOther Zoning set port port number Set Port commandenable alpa bypass alpa Prepares the port for testing DownDiagnostics Disables the port Table 11. SNMP configuration settings Set Setup commandset setup Authority Table 12. System configuration settings Examples Trap2Address show Show commandalarm about fabric domainsdonor interface Description Table 13. Show Port parametersEntry support post logsteering domain_id setup option version topologyusers switch FCSM: user1> show topology Class2FramesIn switch Show Config commandshow config Authority MFS TOV MSEnable True NoClose False FCSM: user1> show config zoning LogoutMonitoringEnabled True RisingTrigger5LOSMonitoringEnabledTrue RisingTrigger100 Configuration Name: default show log Show Log commandsettings component FCSM: user1> show log options show perf Show Perf commanderrors port_number byte Examples FCSM: user1>: show perf Authority Show Setup commandshow setup Syntax FCSM: user1> show setup snmp Authority Shutdown commandshutdown Syntax port port_number test_type Test commandtest Internal for internal and external ports test x external Authority Uptime commanduptime Syntax accounts User commanduser delete account_name admin@OB-session1- in admin mode FCSM admin user1 user del user3FCSM admin : user1> user list admin@OB-session2 user1@OB-session3 Authority Whoami commandwhoami Syntax add zone members Zone commandzone copy zone_source zone_destination rename zone old zone new members zoneremove zone members type zone zone_type wwn_0160ed zone_set_1 wwn_c001b0 zone_set_1 activate zone_set Zoneset commandzoneset active zones zone_set remove zone_set zone_listrename zone_set_old zone_set_new Notes limits Zoning commandedit cancel Examples save wwn_23bd31 50:06:04:82:bf:d2:18:c2 wwn wwn_b0241f 50:06:04:82:bf:d2:18:c250:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:23:bd:31 3 Using the SAN Utility SAN Utility user interface Figure 1. Topology window Figure 2. Faceplate window Table 14. Menu shortcut keys Menu barFigure 3. Menu bar selection examples Toolbar button ToolbarTable 15. Toolbar buttons Toolbar button name Data window and tabs Fabric treeGraphic window Figure 4. Fabric tree Figure 5. Topology window Using the Topology windowWorking status indicator Switch module icon color Fibre Channel switch module and link statusWorking with switch modules and links Status Arranging switch modules in the window Selecting switch modules and links Figure 7. Faceplate window Using the Faceplate windowTopology data window tabs Working with ports Opening the Faceplate window and pop-upmenusPort views and status Selecting ports Faceplate data window tabs Setting up securityManaging fabrics Opening pop-upmenus Removing a fabric Managing the fabric databaseAdding a fabric 5.Click Add fabric Saving a fabric view file Adding a new switch module to a fabricOpening a fabric view file Rediscovering a fabric 2.Click Switch / Delete Replacing a failed switch module in a fabric4.Click Switch / Restore Displaying fabric information Switch module icon Description Figure 9. Active Zonesets window Zoning a fabricActive Zoneset Data window Zones Zoning conceptsAccess control list zones Soft zoning Zone sets Zoning configurationAliases Zoning database Merging fabrics and zoning Using the Zoning Config windowRestoring default zoning Zone merge failure Figure 11. Edit Zoning window Using the Edit Zoning windowZone merge failure recovery Managing zone sets Table 18. Edit Zoning window toolbar buttons Copying a zone to a zone set Creating a zone setActivating and deactivating a zone set Removing all zoning definitions Managing zonesRemoving a zone set Creating a zone in a zone set Removing a zone member Adding zone membersRenaming a zone or a zone set Removing a zone from a zone set Changing zone types Managing aliasesRemoving a zone from all zone sets Creating an alias Removing an alias from all zones Managing switch modulesAdding a member to an alias •Click View ” Refresh Displaying switch module informationName Server data window Figure 12. Faceplate data window Table 19. Name server data window entries Switch Data windowTable 20. Switch data window entries Entry Entry Link data windowTable 20. Switch data window entries continued Description Port Statistics Data window Configured Zonesets Data windowFabric view port graphing application Port Information Data window Configuring alarms Managing alarmsAlarm Log Data window Resetting a switch module Paging a switch moduleSetting the date and time Exporting alarm log information to a file Figure 15. Switch Properties window Configuring a switch moduleSwitch module properties Table 21. Switch module administrative states In-bandmanagement Domain ID and Domain ID LockBroadcast support Table 22. Timeout values Timeout valuesNetwork properties Figure 16. Network Properties window Remote logging Archiving a switch moduleIP configuration Table 23. IP configuration parameters Loading firmware Managing portsManaging firmware Activating the fallback firmware Figure 17. Faceplate Display Data window Displaying port informationMonitoring port status Table 24. Port mode descriptions Table 24. Port mode descriptions continued Displaying port operational statesDisplaying port speeds Table 25. Port operational states Displaying SFP module media status Port graphing and Fabric View applicationPort Statistics Data window Table 27. SFP module media view Total LIP received EntryDescription Port Information data window Table 29. Port Information Data window entries Figure 18. External Port Properties window Configuring portsName Server Data window Figure 19. Internal Port Properties window Changing port administrative states2.Click Port / Port Properties Table 30. Port administrative states Changing port speeds external ports onlyChanging port modes external ports only 2.Click Port / Port Properties 2.Click Port / Port Properties I/O stream guardExtending port credits Table 32. Port modes continued Figure 20. Extended Credits window Resetting a port 2.Click Port ” Reset Port 4 Switch management utility functions LED diagnostics Normal all pass LED flash pattern Fatal error LED flash patternHeartbeat LED patterns Internal firmware failure LED flash pattern Configuration file system error LED flash pattern Switch module fault LED flash patternSwitch module OK LED Port logged-inLED flash patterns Table 33. E-portisolation causes and fixes Port testingPort fault LED flash patterns Figure 22. Port Loopback Test window Fibre Channel switch module monitoring using SNMPSNMP configuration Table 35. SNMP trap configuration parameters SNMP trap configurationTable 34. SNMP configuration parameters Parameter Restoring the factory default configuration Configuration backupConfiguration restore Table 36. Factory default configuration settings Restoring a switch module Using the Fabric View applicationReinitializing the configuration file system Arranging and sizing port performance graphs Starting the Fabric View applicationDisplaying port performance graphs Figure 23. Fabric View graphs Customizing port performance graphs Figure 24. Modify Graph Display window Table 37. Port mapping AMapping port locations and software numberingPort mapping Page B Getting help and technical assistance Using the documentationHardware/Software service and support Before you callPage C Notices Important notes Declaration of the Manufacturer or Importer Regulatory Specifications and DisclaimersSafety Compliance Electromagnetic Compatibility EMC Index Page Page Page